Electrolux Ewm 147410 W User Manual

5. Pull out the emergency emptying cap
from the filter cover, using pliers.
6. When no more water comes out, un-
screw the pump cover by turning it anti-
clockwise, using pliers, and remove the
filter. Always keep a rag nearby to dry
up any water spillages when removing
the cover.
Clean the filter under a tap, to remove
any traces of fluff.
12
7. Remove foreign bodies and fluff from
the pump seat and from the pump im-
peller.
8. Check carefully whether the pump im-
peller rotates (it rotates jerkily). If...

10. Replace the emergency emptying cap
into the filter cover and fix it firmly.
11. Close the pump door.
Warning! When the appliance is in use
and depending on the programme
selected there can be hot water in the
pump. Never remove the pump cover
during a wash cycle, always wait until
the appliance has finished the cycle,
and is empty. When refitting the pump
cover , ensure it is securely re-tightened so as to stop leaks and
young children being able to remove it.
Cleaning the water inlet filters
If you...

Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4. open the pump door;
5. place a bowl on the floor. Remove the
emergency emptying cap from the filter.
The water should drain by gravity into
the bowl. When the bowl is full, refit the
cap into the filter. Empty the bowl. Re-
peat the procedure until water stops flow-
ing out;
6....

ProblemPossible cause/Solution
The machine does not start:
The drying board is on.
• Switch the drying board off.
The door has not been closed. E40
•Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button 8 has
not been pressed.
• Please turn the...

ProblemPossible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the pilot light 9  goes off.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance....

If you are unable to identify or solve the prob-
lem, contact our service centre. Before tele-
phoning, make a note of the model, serial
number and purchase date of your ma-
chine: the Service Centre will require this in-
formation.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Mod. ..
. ... ...
Prod. No.
 ..
. ... ..
         
      
         
 Ser.  N
o. ... ...
 ...
TECHNICAL DATA
DimensionsWidth
Height
Depth
Depth with shelf open60 cm
85 cm
60 cm
92 cm
Electrical connection...

INSTALLATION
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices
so that they can be refitted if the machine
ever has to be transported again.
1. After removing all the packaging, careful-
ly lay machine on it’s back to remove
the polystyrene base from the bottom.
2. Remove the power supply cable and the
draining hose from the hose holders on
the rear of the appliance.
3. Unscrew the three bolts.4. Slide out the relevant...

6. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag contain-
ing the instruction booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the ma-
chine is not impeded by carpets, rugs etc.
Check that the machine does not touch the
wall or other kitchen units. Level the wash-
ing machine by raising or lowering the feet.
The feet may be tight to adjust as they incor-
porate a self locking nut, but...

3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
Water-stop device
The inlet hose is provided with a water stop
device, which protects...

The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local Service Centre.
ELECTRICAL CONNECTION
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
Check that your domestic electrical installa-
tion can take the maximum load required, al-
so taking into account any other appliances
in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept
any...