Electrolux Ewg 12740 W User Manual
Here you can view all the pages of manual Electrolux Ewg 12740 W User Manual. The Electrolux manuals for Washing Machine are available online for free. You can easily download all the documents as PDF.
Page 31
columns and margins electrolux 31 If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. \b \b \f \f \f \f Spinning starts late or the machine does not spin:●The electronic unbalance detection device has cut in...
Page 32
32electrolux technical data Technical data Dimensions Width 60 cm 82 cm 54 cm Height Depth Water supply pressure Minimum 0,05 MPa 0,8 MPa Maximum Cotton Synthetics Delicates Wool/Handwash Silk/LingerieMaximum Load 5 kg 2.5 kg 2.5 kg 1kg 1kg Maximum Spin Speed 1200 rpm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate on the inner edge of the appliance door 132969690_GB.qxd 13/09/2007 11.38 Pagina 32
Page 33
consumption values electrolux 33 Consumption values Water consump tion (in litres)Programme Energy consumption (in kWh)Programmeduration (in minutes) Cottons Normal 90° 1.9 50 Cottons + Pr ewash 90° 2.0560 Synthetics 60° 0.9 53Synthetics Normal+Prewash 60° 0.55 55Delicates 40° Cottons Eco 60°(*) 0.85 47 Cottons Eco + Prewash 60° 1.05 57 0.8 42 For the duration of the programmes, please refer to the display on the control panel. Handwash 40° 0.4 50 Silk 30° 0.4 50 Wool 40° 0.247 Lingerie 40°...
Page 34
34electrolux installation Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. Using a spanner unscrew and remove the rear right bolt. Lay the machine gently on its back, making sure that the hoses are not squashed. 2. Remove the polystyrene base and take off the bottom panel by unscrewing the central screw.. 3. Carefully slide out the...
Page 35
installationelectrolux 35 7. Plug the open holes with the plugs supplied with the instruction booklet. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Level the washing machine by raising or lowering the feet. The feet may be tight to adjust as they incorporate a self locking nut, but the machine MUST be level and stable. \f ...
Page 36
36electrolux installation If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use . Note ! Installation should comply with local water authority and building regulations’ requirements. The appliance must be connected to a cold water supply. A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may...
Page 37
installationelectrolux 37 Electrical connection This machine is designed to operate on a 220-230 V, single-phase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2.2 kW), also taking into account any other appliances in use. Connect the machine to an earthed socket. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced,...
Page 38
38electrolux installation Building-in This appliance has been designed to be built into the kitchen furniture. The recess should have the dimensions shown in picture A. When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped. Picture AB. \f \f \f\f \f ...
Page 39
installationelectrolux 39 b) Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door. The distance between the holes hobs fixing centres must be 416 mm. The distance (B) from upper edge of the door to the centre of the hole depends on the adjacent furnitures dimensions. The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B)...
Page 40
40electrolux building-in With the appliance installed adjust all four feet ensuring the machine is stable, and a clearance of approximately 5 mm is left between the top of the machine and the underside of the worktop. A final check for stability should be car- ried out with the machine on spin with a load, this will identify the need for any further fine adjustment to the feet. A strip of beading approximately 605 mm W, x 5 mm H, x 25 mm D must be screwed down into the base directly in front of the...