Electrolux Ewg 12450 W User Manual

Installation
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit
devices so that they can be refitted if the
machine ever has to be transported
again.
1. After removing all the packaging,carefully lay machine on it’s back to
remove the polystyrene base from the
bottom.
2. Remove the power supply cable and the draining hose from the hose
holders on the rear of the appliance.
3. With the supplied spanner unscrew and remove the central...

32electrolux installation
6. Fill the smaller upper hole and the two
large ones with the corresponding
plastic plug caps supplied in the bag
containing the instruction booklet that
you will find inside the drum.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets,
rugs etc. Check that the machine does
not touch the wall or other kitchen units.
Carefully level by screwing the
adjustable feet in or out.  The machine
MUST be...

3. Set the hose correctly by looseningthe ring nut. 
After positioning the inlet hose, be
sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4” thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened.
If it is too short and you do not wish to
move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
Water-stop device
The inlet hose is provided with a water
stop device, which protects...

Place the drain hose into your stand-
pipe, which should have an internal
diameter of approximately 38mm thus
ensuring there is an air break between
the drain hose and standpipe.
When discharging into a standpipe
ensure that the top of the standpipe is
no more than 90cm (35.4) and no
less than 60cm (23.6) above floor
level.
The drain hose may be extended to a
maximum of 4 metres. An additional
drain hose and joining piece is available
from your local Service Force Centre. 
The joining piece must have an...

installationelectrolux  35
If you intend to drain the hose from the
machine into a sink, make sure that the
sink is empty and the plug hole is not
blocked. Use the plastic “U -Piece”
supplied.
Important!
Before connecting up the machine to
new pipework or to pipework that has
not been used for some time, run off a
reasonable amount of water to flush
out any debris that may have collected
in the pipes.
Special conditions
If the floor is carpeted or covered with
crumbly or soft material, insert a rigid...

36electrolux installation
Electrical connection
Any electrical work required to install
this appliance should be carried out by
a qualified electrician or competent
person.
Warning!
THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any lia-
bility should this safety measure
not be observed.
Before switching on, make sure the
electricity supply voltage is the same
as that indicated on the appliance’s
rating plate. 
Important!
Information on the electrical
connection is given on the rating
plate...

installation electrolux  37
ance power supply cable neeed to
be replaced, this must be carried
out by our Service Force Centre.
Note
When the appliance is installed the
power supply cable must be accessi-
ble.
Permanent connection
In the case of permanent connection it
is necessary that you install a double
pole switch between the appliance and
the electricity supply (mains), with a
minimum gap of 3mm between the
switch contacts and of a type suitable
for the required load in compliance with
the current...

38electrolux  installation
b) Hinges
To mount the hinges it is necessary to
drill two holes (dia. 35 mm, depth
12.5-14 mm depending on the depth
of door furniture) on the inner side of
the door. The distance between the
holes hobs fixing centres must be 416
mm.
The distance (B) from upper edge of
the door to the centre of the hole
depends on the adjacent furnitures
dimensions.
The required dimensions are given in
the picture C.
The hinges will be fixed to the door by
means of screws for wood (2-Fig. B)...

installationelectrolux  39
to construct the base should have a
non slip surface, be water repellent and
if possible be one solid piece.
If it is not possible to use one solid
piece, due to the additional height
required, ensure that any additional
strips of timber are glued and screwed
to the underside of the base (see Fig.
F).
Drill four fixing holes see Fig. G.
Position the base into the recess with
its front edge as far forward as the
adjoining plinth line will allow. 
The reason for placing the base...

40electrolux   environment concerns
Environment concerns
Packaging materials
The materials marked with the symbol
are recyclable.
>PEPSPP