Electrolux Ewf 147540 User Manual

EWF 147540 W................................................ .............................................
ENWASHING MACHINE USER MANUAL
 

Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information   2
Product description   4
Control panel   5
First use   7
Personalisation  8
Daily use   8
Helpful hints and tips   11
Washing programmes   12Care and cleaning   15
What to do if…   19
Technical data   21
Consumption values   22
Installation  22
Electrical connection   25
Environment concerns   25
Subject to change without notice.
 SAFETY INFORMATION
Important! Read carefully & keep for future...

INSTALLATION
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check
that it is not damaged. If in doubt, do not
use it and contact the Service Centre.
• All packing and transit bolts must be re-
moved before use. Serious damage can
occur to the product and to property if
this is not adhered to. See relevant sec-
tion in the user manual.
• After having installed the appliance,
check that it is not standing on the inlet
and drain hose and the worktop is not...

PRODUCT DESCRIPTION
Your new appliance meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption. Its new washing system allows to-
tal use of detergent and reduces water consumption so saving energy.
4
5
12
3
6
1Detergent dispenser drawer
2Control panel
3Door opening handle
4Rating Plate
5Drain pump
6Adjustable feet
DETERGENT DISPENSER DRAWER
 Compartment for detergent used for
prewash and soak phase or for stain re-
mover used during the stain...

CONTROL PANEL
Below is a picture of the control panel. It shows the programme selector dial as well as
the buttons, pilot lights and the display. These are presented by relevant numbers on
the following pages.
123456789
1Programme selector dial
2Display
3TEMPERATURE button
4SPIN reduction button
5PREWASH button
6EXTRA RINSE button
7DELAY START button
8START/PAUSE button
9TIME MANAGER buttons
PROGRAMME SELECTOR DIAL
It allows you to switch the appliance on/off
and/or to select a programme.
TEMPERATURE...

DISPLAY
2.12.22.32.42.52.62.72.82.9
2.122.112.10
The display shows the following informa-
tion:
2.1:Temperature value
2.2: Temperature icons 
 , Cold  .
During the washing cycle the display shows
the temperature icon animated to indicate
that the appliance has started the heating
phase of the water in the tub.
2.3: Spin value
2.4: Spin speed icons.
•
No spin 
•
Rinse Hold 
•
Night Cycle 
During the spinning phase the spiral is ani-
mated.
No spin option eliminates all the spin pha-
ses and increases the...

In the event of operating problems, some
alarm codes can be displayed, for exam-
ple 
 (see paragraph «What to do
if...»).
•Delay Time value
2.10: Soil degree icons
•
Intensive 
•
Normal 
•
Daily 
•
Light 
•
Quick 
•
Super Quick 
•
Refresh 
•
Super Refresh 
(see paragraph «Select Time Manager op-
tion»).
2.11: Clock icon 
After the programme has started, the dura-
tion is displayed and the clock icon is ani-
mated.
2.12: Washing programme phase icons
By selecting the wash programme, the
washing programme...

PERSONALISATION
ACOUSTIC SIGNALS
The machine is provided with an acoustic
device, which sounds in the following ca-
ses:
• at the end of the cycle
• if there is a fault.
By pressing the 5 and 6 buttons simultane-
ously for about 6 seconds, the acoustic
signal is deactivated (except if there is a
fault). By pressing these 2 buttons again,
the acoustic signal is reactivated.
CHILD SAFETY LOCK
This device permits you to leave the appli-
ance unattended and not to worry that chil-dren might be injured by or...

SELECT THE REQUIRED PROGRAMME
BY TURNING THE PROGRAMME
SELECTOR DIAL (1)
Turn the programme selector dial to the re-
quired programme. The washing machine
will propose a temperature and automati-
cally select the maximum spin value provi-
ded for the programme you have chosen.
You can change these values by operating
the corresponding buttons. The green pilot
light of the button 8 starts to flash.
The selector dial can be turned either clock-
wise or counterclockwise. Turn to position
 to reset...

START THE PROGRAMME BY
PRESSING BUTTON 8
To start the selected programme, press the
button 8, the green pilot light of the button
8 stops blinking. The icon 2.8 appears on
the display to indicate that the appliance
starts operating and the door is locked.
To interrupt a programme which is running,
press the button 8: the green pilot light
starts to blink.
To restart the programme from the point at
which it was interrupted, press the button 8
again. If you have chosen a delayed start,
the machine will...