Electrolux Ewf 14680 User Manual

• Place a containfer close to the pump
to collect any spillage. 
• When no more water comes out,
unscrew the pump cover and remove
it. Always keep a rag nearby to dry up
spillage of water when removing the
cover.
• Remove any objects from the pump
impeller by rotating it.
• Screw the pump cover fully in.
• Close the pump door.
Warning!
When the appliance is in use and
depending on the programme selected
there can be hot water in the pump.
Never remove the pump cover during a
wash cycle, always wait until...

22electrolux
Emergency emptying out
If the water is not discharged, proceed
as follows to empty out the machine:
• pull out the plug from the power
socket; 
• close the water tap; 
• if necessary, wait until the water has
cooled down;
• open the pump door;
• place a bowl on the floor the water
should drain by gravity into the bowl.
When the bowl is full, empty the bowl.
Repeat the procedure until water
stops flowing out;
• clean the pump if necessary as
previously described;
• screw the pump cover again...

Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be
solved easily without calling out an engineer. Before contacting your local Service
Centre, please carry out the checks listed below.
During machine operation it is possible that the redStart/Pause pilot light flashes to
indicate that the machine is not working.
Once the problem has been eliminated, press the Start/Pausebutton to restart the
programme. If after all checks, the problem persists,...

24electrolux
MalfunctionPossible causeSolution
The machine does not empty
and/or does not spin:●The drain hose is squashed
or kinked. (Red Start/
Pause pilot light flashes)
●The drain pump is clogged.
(Red Start/Pause pilot
light flashes)
●The option or has
been selected.
●The laundry is not evenly
distributed in the drum.
●Check the drain hose
connection.
●Clean the drain pump.
●Select the Drain or Spin
programmes
●Redistribute the laundry.
There is water on the floor:●Too much detergent or
unsuitable...

MalfunctionPossible causeSolution
The machine vibrates or is
noisy:●The transit bolts and
packing have not been
removed.
●The support feet have not
been adjusted.
●The laundry is not evenly
distributed in the drum.
●Maybe there is very little
laundry in the drum.
●Check the correct
installation of the appliance.
●Check the correct levelling
of the appliance.
●Redistribute the laundry.
●Load more laundry.
Spinning starts late or the
machine does not spin:●The electronic unbalance
detection device has cut...

26electrolux 
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the
model, serial number and purchase date
of your machine: the Service Centre will
require this information.
Technical data
Dimensions Width 60 cm
85 cm
64 cm Height
Depth (inclunding the porthole)
Water supply pressure Minimum 0,05 MPa
0,8 MPa Maximum
Cotton
Synthetics
Delicates
Woollens and handwashMaximum Load 7  kg
3,5 kg
3,5 kg
2 kg
MaximumSpin Speed01200 rpm (EWF...

electrolux  27
Consumption values
Programme
duration 
(in minutes)Programme Energy
consumption 
(in kWh)Water
consumption 
(in litres)
140Cottons 90°2.363
155Cottons 60°+ (*)1.1959
120Cottons 60°1.563
90Synthetics 60°0.951
65Delicates 40°0.555
60Wool 40°0.455
55Handwash 40°0.2555
45 Rinses 0.1 42
2 Drain - -
10 Spin - -
(*) The “Cottons 60° and option Eco 
selected
” is the reference programme
for the data entered in the energy
label, in compliance with EEC 92/75
standards.
The consumption data shown on...

Installation
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit
devices so that they can be refitted if the
machine ever has to be transported
again.
1. Unscrew and remove the three rear
screws by means of a key.
2. .Open the porthole and remove the
polystirene block fitted on the doos
seal.
3. Place the machine in an upright
position and remove the three plastic
bolts.
4. Plug the 3 holes with the plastic plugs
which you can find in...

electrolux 29
IMPORTANT:The distance from the
floor to the highest part of the hose
should be between 60 to 90 cm. (It is
advised to be between 60 and 70 cm).
The hose must not be bent nor twisted
to avoid clogging. Should a prolonga-
tion of the discharging hose be
unavoidable this must never surpass
1.5 m and must be of the same diame-
ter as the original hose. Make sure the
hoses are not too tense. 
Levelling
Level the washing machine by loosening
or tightening the feet. Once in the right
position fix...

Environment concerns
Packaging materials
The materials marked with the symbol
are recyclable.
>PEPSPP