Electrolux Ewf 12470 W User Manual

							MalfunctionPossible causeSolution
The machine vibrates or is
noisy:●The transit bolts and
packing have not been
removed.
●The support feet have not
been adjusted.
●The laundry is not evenly
distributed in the drum.
●Maybe there is very little
laundry in the drum.
●Check the correct
installation of the appliance.
●Check the correct levelling
of the appliance.
●Redistribute the laundry.
●Load more laundry.
Spinning starts late or the
machine does not spin:●The electronic unbalance
detection device has cut in
because the laundry is not
evenly distributed  in the
drum. The laundry is
redistributed by reverse
rotation of the drum. This
may happen several times
before the unbalance
disappears and normal
spinning can resume. If,
after 10 minutes, the
laundry is still not evenly
distributed in the drum, the
machine will not spin. In this
case, redistribute the load
manually and select the
spin programme.●Redistribute the laundry.
The door will not open:●The programme is still
running.
●The door lock has not been
released.
●There is water in the drum.
●Wait the end of washing
cycle.
●Wait for the Door icon 
desappearing.
●Select drain or spin
programme to empty out
the water.
something not working electrolux  31
132979220.qxd  30/08/2006  12:04  Pagina  31
 
						

							MalfunctionPossible causeSolution
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the
model, serial number and purchase date
of your machine: the Service Centre will
require this information.

	

	






The machine makes an
unusual noise●The machine is fitted with a
type of motor which makes
an unusual noise compared
with other traditional
motors. This new motor
ensures a softer start and
more even distribution of
the laundry in the drum
when spinning, as well as
increased stability of the
machine.
No water is visible in the
drum●Machines based on modern
technology operate very
economically using very little
water  without affecting
performance.
32electroluxsomething not working
132979220.qxd  30/08/2006  12:04  Pagina  32
 
						

							Technical data
Dimensions Width 60 cm
85 cm
63 cm Height
Depth
Water supply pressure Minimum 0,05 MPa
0,8 MPa Maximum
Cotton
Synthetics
Delicates
Woollens and handwash
Jeans
Lingerie/SilkMaximum Load6     kg
2.5 kg
2.5 kg
2 kg
3kg
1kg
MaximumSpin Speed1000 rpm (EWF 10470W)
1200 rpm (EWF 12470W)
1400 rpm (EWF 14470W) 
Electrical connection Voltage
- Overall power - FuseInformation on the electrical connection is given on
the rating plate on the inner edge of the appliance
door
technical data  electrolux33
132979220.qxd  30/08/2006  12:04  Pagina  33
 
						

							34electroluxconsumption value
Consumption values
Water
consumption 
(in litres)Programme Energy
consumption 
(in kWh)Programme
duration 
(in minutes)
Cottons Normal 95° 2.162
Cottons  Eco 60° (*)1.02 54
Cottons + Prewash 2.374
Cottons  Eco + Prewash1.4 72
Synthetics 60°
0.85 52
For the duration of the programmes, please refer to the display on the
control panel.
Handwash 40° 0.145
Lingerie 40° --
Silk 30° -- Synthetics Eco
0.5 60
Synthetics Eco +Prewash0.4 58
Delicates 40° 0.458
Wool 40° 0.2550 Synthetics + Prewash 0.549
Spin --
Delicate Spin -- Jeans 40° 0.458
Soak 0.3555
Rinses -- Delicates + Prewash 0.458
132979220.qxd  30/08/2006  12:04  Pagina  34
 
						

							The consumption data shown on this
chart is to be considered purely
indicative, as it may vary depending on
the quantity and type of laundry, on the
inlet water temperature and on the
ambient temperature. It refers to the
highest temperature for each wash
programme.(*) The programme “Cottons Eco  ” at
60°C is the reference programme for
the data entered in the energy label,
in compliance with EEC 92/75
standards.
consumption value  electrolux 35
132979220.qxd  30/08/2006  12:04  Pagina  35
 
						

							36electrolux installation
Installation
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit
devices so that they can be refitted if the
machine ever has to be transported
again.
1. After removing all the packaging,
carefully lay machine on it’s back to
remove the polystyrene base from the
bottom.
2. Remove the power supply cable and
the draining hose from the hose
holders on the rear of the appliance.
3. With a suitable spanner unscrew and
remove the central rear bolt A. Slide
out the relevant plastic spacer.
	
	
4. Unscrew and remove the two large
rear bolts Band the six smaller bolts
C.
5. Remove the bracket Dand tighten up
the six smaller bolts C.


	
	

	



	

132979220.qxd  30/08/2006  12:04  Pagina  36
 
						

							6. Open the porthole, take out the inlet
hose from the drum and remove the
polystyrene block fitted with the
adhesive tape on the door seal.
7. Fill the smaller upper hole and the two
large ones with the corresponding
plastic plug caps supplied in the bag
containing the instruction booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets,
rugs etc. Check that the machine does
not touch the wall or other kitchen units.
Level the washing machine by raising or
lowering the feet. The feet may be tight
to adjust as they incorporate a self
locking nut, but the machine MUST be
level and stable.
If necessary, check the setting with a
spirit level.
Any necessary adjustment can be made
with a spanner. 
	
	
Accurate levelling prevents vibration,
noise and displacement of the machine
during operation.Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
Water inlet
An inlet hose is supplied and can been
found inside the machine drum. Do not
use the hose from your previous
machine to connect to the water supply.
1. Open the porthole and extract the
inlet hose.
2. Connect the hose with the angled
connection to the machine.
Do not place the inlet hose
downwards. Angle the hose to the
left or right depending on the
position of your water tap.
3. Set the hose correctly by loosening
the ring nut. 
	
	
installationelectrolux  37
132979220.qxd  30/08/2006  12:04  Pagina  37
 
						

							38electroluxinstallation
After positioning the inlet hose, be
sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance. 
The inlet hose must not be lengthened. If
it is too short and you do not wish to
move the tap, you will have to purchase
a new, longer hose specially designed
for this type of use.
Water drainage
The end of the drain hose can be
positioned in three ways:
Hooked over the edge of a sink
using the plastic hose guide
supplied with the machine.In this
case, make sure the end cannot come
unhooked when the machine is
emptying. This could be done by tying it
to the tap with a piece of string or
attaching it to the wall.





In a sink drain pipe branch.This
branch must be above the trap so that
the bend is at least 60 cm above the
ground. 
Directly into a drain pipe at a
heightof not less than 60 cm and not
more than 90 cm. The end of the drain
hose must always be ventilated, i.e.
the inside diameter of the drain pipe
must be larger than the outside diameter
of the drain hose.
The drain hose must not be kinked.
The drain hose may be extended to a
maximum of 4 metres. An additional
drain hose and joining piece is available
from your local Service Centre.

132979220.qxd  30/08/2006  12:04  Pagina  38
 
						

							Electrical connection
This machine is designed to operate on
a 220-230 V, single-phase, 50 Hz
supply.
Check that your domestic electrical
installation can take the maximum load
required (2.2 kW), also taking into
account any other appliances in use.
Connect the machine to an earthed
socket. 
The manufacturer declines any
responsibility for damage or injury
through failure to comply with the above
safety precaution. Should the appliance
power supply cable need to be
replaced, this should be carried out by
our Service Centre.
Please ensure that when the appliance is
installed the power supply cable is easily
accessible.
installationelectrolux  39
132979220.qxd  30/08/2006  12:04  Pagina  39
 
						

							Environment concerns
Packaging materials
The materials marked with the symbol
are recyclable.
>PEPSPP