Electrolux Ewf 12270 W User Manual

							Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with ace-
tone
1), lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits.
Treat any residual marks with bleach.
Red wine: soak in water and detergent,
rinse and treat with acetic or citric acid, then
rinse. Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten
the fabric first with acetone
1), then with acetic
acid; treat any residual marks on white fab-
rics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, me-
thylated spirits or benzine, then rub with de-
tergent paste.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the en-
vironment.
Although biodegradable, detergents contain
substances which, in large quantities, can
upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine de-
tergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics
(60°C max) and woollens
• liquid detergents, preferably for low tem-
perature wash programmes (60°C max)
for all types of fabric, or special for wool-
lens only.The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
If using liquid detergents, a programme
without prewash must be selected.
Your appliance incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Follow the product manufacturer’s recom-
mendations on quantities to use and do not
exceed the «MAX» mark in the detergent
dispenser drawer .
Quantity of detergent to be used
The type and quantity of detergent will de-
pend on the type of fabric, load size, degree
of soiling and hardness of the water used.
Follow the product manufacturers’ instruc-
tions on quantities to use.
Use less detergent if:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during wash-
ing.
Degrees of water hardness
Water hardness is classified in so-called “de-
grees” of hardness. Information on hardness
of the water in your area can be obtained
from the relevant water supply company, or
from your local authority. If the water hard-
ness degree is medium or high we suggest
you to add a water softener following always
the manufacturer’s instructions. When the
degree of hardness is soft, readjust the quan-
tity of the detergent.
1) do not use acetone on artificial silkelectrolux  11
 
						

							Washing programmes
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
COTTON 95°-30°
Main wash - Rinses
Maximum spin speed 1200 rpm
Max. load 6 kg - Red. load 3 kg 
1)
For white and coloured cotton (normally soiled
items).
SPIN, RINSE HOLD,
NIGHT CYCLE, DAI-
LY, LIGHT, QUICK,
EXTRA RINSE
COTTON ECONOMY  60°
Main wash - Rinses
Maximum spin speed 1200 rpm
Max. load 6 kg
White and fast coloured cottons .
This programme can be selected for slightly or normally
soiled cotton items. The temperature will decrease and
the washing time will be extended. This allows to obtain
a good washing efficiency so saving energy.
SPIN, RINSE HOLD,
NIGHT CYCLE, EX-
TRA RINSE
COTTON ECONOMY  40°
Main wash - Rinses
Maximum spin speed 1200 rpm
Max. load 6 kg
White and coloured cottons .
This programme can be selected for slightly soiled cot-
ton items. The temperature will decrease and the wash-
ing time will be extended. This allows to obtain a good
washing efficiency so saving energy.
SPIN, RINSE HOLD,
NIGHT CYCLE, EX-
TRA RINSE
COTTON WITH PREWASH  + 95°
Prewash - Main wash - Rinses
Maximum spin speed 1200 rpm
Max. load 6 kg - Red. load 3 kg 
1)
For white cottons with prewash phase.
SPIN, RINSE HOLD,
NIGHT CYCLE, DAI-
LY, LIGHT, QUICK,
EXTRA RINSE 2)
COTTON WITH PREWASH   + 60°
Prewash - Main wash - Rinses
Maximum spin speed 1200 rpm
Max. load 6 kg - Red. load 3 kg 
1)
For white or coloured cottons with prewash phase
(heavily soiled items).
SPIN, RINSE HOLD,
NIGHT CYCLE, DAI-
LY, LIGHT, QUICK,
EXTRA RINSE 2)
SYNTHETIC 60°-30°
Main wash - Rinses
Maximum spin speed 900 rpm
Max. load 3 kg - Red. load 1,5 kg 
1)
Synthetic or mixed fabrics: underwear, coloured gar-
ments, non-shrink shirts, blouses.
SPIN, RINSE HOLD,
NIGHT CYCLE, DAI-
LY, LIGHT, QUICK,
EXTRA RINSE
12  electrolux
 
						

							Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
DELICATE 40°-30°
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load kg 3 - Red. load kg 1,5
1)
Delicate fabrics: acrylics, viscose, polyester.
RINSE HOLD, NIGHT
CYCLE, DAILY,
LIGHT, QUICK, EX-
TRA RINSE
WOOL 40°
Main wash - Rinses
Maximum spin speed 900 rpm
Max. load 1 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate fabrics.
Note  : A single or bulky item may cause imbalance. If
the appliance doesn’t perform the final spin phase, add
more items, redistribute the load manually and then se-
lect the spinning programme.
SPIN, RINSE HOLD,
NIGHT CYCLE
HANDWASH 30°- Cold
Main wash - Rinses
Maximum spin speed 900 rpm
Max. load 1 kg
Special programme for delicate fabrics with «hand
washing» care symbol.
SPIN, RINSE HOLD,
NIGHT CYCLE
RINSES Rinses
Maximum spin speed 1200 rpm
Max. load 6 kg
With this programme it is possible to rinse and spin cot-
ton garments which have been washed by hand. The
machine performs 3 rinses, followed by a final long spin.
The spin speed can be reduced by pressing the relevant
button.
SPIN, RINSE HOLD,
NIGHT CYCLE, EX-
TRA RINSE
DRAIN Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in pro-
grammes with the Rinse Hold and Night Cycle option
selected.
  
SPIN Drain and long spin
Maximum spin speed 1200 rpm
Max. load 6 kg
Separate spin for hand washed garments and after pro-
grammes with the Rinse Hold and Night Cycle option
selected. You can choose the spin speed by pressing
the relevant button to adapt it to the fabrics to be spun.
SPIN 
electrolux  13
 
						

							Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
 (=OFF)
For cancelling the programme which is running or to
switch the machine off .  
1) If you select the Quick option by pressing button 3 , we recommend that you reduce the maximum
load as indicated. (Red. load = reduced load). Full loading is possible however with somewhat reduced
cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
Care and cleaning
Warning! You must disconnect the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder manufac-
turers instructions. This will help to prevent
the formation of lime deposits.
After each wash
Leave the door open for a while. This helps
to prevent mould and stagnant smells form-
ing inside the appliance. Keeping the door
open after a wash will also help to preserve
the door seal.
Maintenance wash
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash pro-
gramme.
• Use a normal measure of detergent, must
be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance
with soap and water only, and then dry thor-
oughly.Important! Do not use methylated spirits,
solvents or similar products to clean the
cabinet.
Cleaning the dispenser drawer
The detergent dispenser drawer should be
cleaned regularly.
1. Remove the detergent dispenser drawer
by pulling it firmly. Remove any traces of
accumulated powder. To aid cleaning,
the top part of the additive compartment
should be removed.
2. Remove the conditioner insert from the
appropriate compartment.
14  electrolux
 
						

							3. Clean all parts with water.
4. Put the conditioner insert in as far as it will
go, so that it is firmly in place
5. Clean all parts of the machine, especially
the nozzles in the top of the washing-in
chamber, with a brush.
6. Insert the detergent dispenser drawer in
the guide rails and push it in.
Washing drum
Rust deposits in the drum may occur due to
rusting foreign bodies in the washing or tap
water containing iron.
Important! Do not clean the drum with
acidic descaling agents, scouring agents
containing chlorine or iron or steel wool.
1. Remove any rust deposits on the drum
with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing
to clean off any cleaning agent residues.Programme: Short Cotton Programme at
maximum temperature and add approx.
1/4 measuring cup of detergent.
Door seal
Check from time to time the door seal and
eliminate eventual possible objects that
could be trapped in the fold.
Drain pump
The pump should be inspected regularly and
particularly if:
• the machine does not empty and/or spin
• the machine makes an unusual noise dur-
ing draining due to objects such as safety
pins, coins etc. blocking the pump.
Proceed as follows:
1. Disconnect the appliance.
2. If necessary wait until the water has
cooled down.
3. Open the pump door.
4. Place a container close to the pump to
collect any spillage.
electrolux  15
 
						

							5. Release the emergency emptying hose,
place it in the container and remove its
cap cover.
6. When no more water comes out, un-
screw the pump and remove it. Always
keep a rag nearby to dry up spillage of
water when removing the pump.
7. Remove any objects from the pump im-
peller by rotating it.
8. Refit the cap on the emergency empty-
ing hose and place the latter back in its
seat.
9. Screw the pump fully in.
10. Close the pump door.
Warning!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump. Never remove the pump
cover during a wash cycle, always wait until
the appliance has finished the cycle, and is
empty. When replacing the cover, ensure it
is securely retightened so as to stop leaks
and young children being able to remove it.
Cleaning the water inlet filters
If you notice that the machine is taking longer
to fill, check that the filter in the water inlet
hose is not blocked.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter in the hose using a hard
bristle brush.
4. Screw the hose back onto the tap.
16  electrolux
 
						

							5. Unscrew the hose from the machine.
Keep a rug nearby because some water
may flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4. open the pump door;
5. place a bowl on the floor and place the
end of the emergency emptying hose into
the bowl. Remove its cap. The water
should drain by gravity into the bowl.
When the bowl is full, put the cap backon the hose. Empty the bowl. Repeat the
procedure until water stops flowing out;
6. clean the pump if necessary as previously
described;
7. replace the emergency emptying hose in
its seat after having plugged it;
8. screw the pump again and close the
door.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed
as follows:
1. close the water tap and unscrew the wa-
ter inlet hose from the tap;
2. place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain
out;
3. screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
By doing this, any water remaining in the ma-
chine is removed, avoiding ice forming and
consequently damage to the appliance.
When you use the machine again, make sure
that the ambient temperature is above 0°C.
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main wash
compartment of the detergent drawer and
then run the drain programme. This will
activate the ECO Valve device avoiding that
part of the detergent remains unused at next
washing.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that
the red pilot light of button 6 blinks, one of
the following alarm codes appears on the
display to indicate that the machine is not
working:• : problem with the water supply.
•
 : problem with the water draining.
•
 : door open.
Once the problem has been eliminated,
press the button 6 to restart the programme.
If after all checks, the problem persists, con-
tact your local Service Centre.
electrolux  17
 
						

							ProblemPossible cause/Solution
The washing machine does
not start:
The door has not been closed. •Close firmly the door.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button 6 has not
been depressed.
• Please turn the selector dial and press the button 6 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The machine does not fill:
The water tap is closed. •Open the water tap.
The inlet hose is squashed or kinked. 
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked. 
• Clean the water inlet filters (See Cleaning the water inlet filters
for more details).
The door is not properly closed. 
•Close firmly the door.
The machine does not emp-
ty and/or does not spin:
The drain hose is squashed or kinked. • Check the drain hose connection.
The drain filter is clogged. 
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or
a that eliminates all the spinning phases has been selected.
• Disable the option.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings.
It is not always easy to see this as the water runs down the hose;
check to see if it is damp.
• Check the water inlet hose connection.
The drain hose is damaged.
• Change it with a new one.
The cap on the emergency emptying hose has not been replaced
or the filter has not been properly screwed in after cleaning action.
• Refit the cap on the emergency emptying hose or screw the filter
fully in.
Unsatisfactory washing re-
sults:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
18  electrolux
 
						

							ProblemPossible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the pilot light 8.2 has gone out.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The machine makes an un-
usual noise:The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor en-
sures a softer start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of the machine.
No water is visible in the
drum:Machines based on modern technology operate very economically
using very little water without affecting performance.
If you are unable to identify or solve the prob-
lem, contact our service centre. Before tele-
phoning, make a note of the model, serial
number and purchase date of your machine:
the Service Centre will require this informa-
tion.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Mod. ..
. ... ...
Prod. No.
 ..
. ... ..
         
      
         
 Ser. N
o. .
.. ...
 ...
Technical data
DimensionsWidth
Height
Depth60 cm
85 cm
63 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating plate,
on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin SpeedMaximum1200 rpm
electrolux  19
 
						

							Consumption values
ProgrammeEnergy consumption
(KWh)Water consumption
(litres)Programme duration
(Minutes)
White Cottons 95°2.061
For the duration of
the programmes,
please refer to the
display on the con-
trol panel.Cottons 60°1.358
Cotton ECO 60° 1)1.0254
Cottons 40°0.758
Synthetics 40°0.550
Delicates 40°0.5560
Handwash 30°0.2553
1) «Cotton ECO» at 60°C with a load of 6 kg is the reference programme for the data entered in the
energy label, in compliance with EEC 92/75 standards.
The consumption data shown on this
chart is to be considered purely indica-
tive, as it may vary depending on thequantity and type of laundry, on the inlet
water temperature and on the ambient
temperature.
Installation
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
3. Unscrew the three bolts.
20  electrolux