Electrolux Ewf 107410 User Manual

The appliance does not drain the wa-
ter.
Change a function
You can change only some functions be-
fore they operate.
1. Press the Start/Pause button.
2. Change the function set.
Set the delay start
1. Press the delay start button again and
again until the display shows the num-
ber hours.
2. Press the start/pause button, the appli-
ance starts the countdown of the delay
start. The symbol h flashes in the dis-
play and the indicator of the start/
pause is off.
When the countdown is completed, the...

Caution! Do not use alcohol, solvents
or chemical products.
Descaling
The water we use contains limescale. If it
becomes necessary, use a water softener
to remove limescales.
Use a special product made for washing
machines. Obey the instructions that you
find on the packaging of the manufacturer.
Do this separately from the laundry wash.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the
drum. Make regularly a maintenance wash.
To do this:
• Empty the...

• The drum cannot turn.
• The appliance makes an unusual noise
because of the blockage of the drain
pump.
Warning!
1. Disconnect the mains plug from
the mains socket.
2. Do not remove the filter while the
appliance operates. Do not clean
the drain pump if the water in the
appliance is hot. The water must
be cold before you clean the drain
pump.
1. Open the pump door.
2. Put a container below the recess of the
drain pump to collect the water that
flows out.
3. Unscrew the filter to let the water flow...

• The appliance does not fill with water.
• The appliance fills with the water for a
long time.
Warning! Disconnect the mains plug
from the mains socket.
To clean the filter:
1. Close the water tap.
2. Remove the inlet hose behind the appli-
ance.
3. Clean the filter in the valve with a stiff
brush or a towel.
       
4. Install again the inlet hose. Make sure
that the couplings are tight to prevent
leakages.
5. Open the water tap.
Emergency drain
Because of a malfunction, the appliance
cannot drain the...

ProblemPossible causePossible solution
The appliance does not
start.The mains plug is not connec-
ted in the mains socket.Put in the mains plug.
 The fuse in the box fuse is
damage.Replace the fuse.
 The appliance door is open.Close the door firmly.
 You do not press the start but-
tonPress the start button.
 The programme knob is not in
the correct position.Turn the programme knob in the correct
position.
 The delay start is set.
It is available only for models
with the Delay start.To start immediately...

ProblemPossible causePossible solution
 There is water in the drum.Set the drain or the spin programme.
The appliance makes
an unusual noise.Incorrect level of the appli-
ance.Adjust the level of the appliance. Refer
to Installation.
 You did not remove the pack-
aging and/or the transit bolts.Remove the packaging and/or the trans-
it bolts. Refer to Installation.
 The load is very small.Add more laundry in the drum.
The appliance fills with
water and drain imme-
diately.The end of the drain hose is
too...

3. Remove the internal film.
4. Open the door and remove all the items
from the drum.
5. Put the front piece on the floor behind
the appliance. Carefully put down the
appliance with the rear side on it. Make
sure not to damage the hoses.
6. Remove the polystyrene protection
from the bottom.
1
2
7. Install the plastic cover (A), removed
from the top of the packaging, to the
bottom of the appliance. Remove the
adhesive strip and close the bottom of
the appliance. Attach permanently the
plastic cover to the...

10. Replace the plastic spacers with the
large plastic caps. You can find these
large caps in the user manual bag.
Warning! Remove all the packaging
and the transit bolts before you install
the appliance.
We recommend that you keep the
packaging and the transit bolts for
when you move the appliance.
Positioning and levelling
• Install the appliance on a flat hard floor.
• Make sure that carpets do not stop the
air circulation below the appliance.
• Make sure that the appliance does not
touch the wall or...

With the plastic hose guide.
•
• On the edge of a sink.
Make sure that the plastic guide cannot
move when the appliance drains. Attach
the guide to the water tap or the wall.
• To a stand pipe with vent-hole.
Refer to the illustration. Directly into a
drain pipe at a height of not less than 60
cm and not more than 90 cm. The end of
the drain hose must always be ventila-
ted , i.e. the inner diameter of the drain-
pipe must be larger than the external di-
ameter of the drain hose.
Without the plastic hose...

155219070-A-182011
 www.electrolux.com/shop