Electrolux Esl 67050 User Manual

							Test in accordance with EN 50242  must be
carried out when the salt container and rinse
aid dispenser have been filled with salt andrinse aid respectively and using the test pro-
gramme (refer to Washing programmes).
Full load: 12 standard place settings
Amount of detergent required:5 g + 25 g (Type B)
Rinse aid settingposition 4 (Type III)
Testing MUST be carried out with:
•NO glass holder,
• NO soft spikes
• NO mini cutlery basket.
REMOVE these items from the upper
basket.
Arrangement upper basket
Arrangement lower basket
Arrangement cutlery basket
Installation
Warning! Any electrical and/or
plumbing work required to install
this appliance should be carried out
by a qualified electrician and/or
plumber or competent person.Remove all packaging before positioning the
machine.
If possible, position the machine next to a
water tap and a drain.
This dishwasher is designed to be fitted un-
der a kitchen counter or work surface.
electrolux  21
 
						

							Attention! Carefully follow the instructions
on the enclosed template for building in the
dishwasher and fitting the furniture panel.
No further openings for the venting of the
dishwasher are required, but only to let the
water fill and drain hose and power supply
cable pass through.
The dishwasher incorporates adjustable feet
to allow the adjustment of the height.
During all operations that involve accessibility
to internal components the dishwasher has
to be unplugged.
When inserting the machine, ensure that the
water inlet hose, the drain hose and the sup-
ply cable are not kinked or squashed.
Fixing to the adjacent units
The dishwasher must be secured against tilt-
ing.Therefore make sure that the counter it is
fixed under, is suitably secured to a fixed
structure (adjacent kitchen unit cabinets,
wall).
Levelling
Good levelling is essential for correct closure
and sealing of the door.
When the appliance is correctly levelled, the
door will not catch on either side of the cab-
inet .
If the door does not close correctly, loosen
or tighten the adjustable feet until the ma-
chine is perfectly level.
Water connection
Water inlet connection
This appliance can be connected to either a
hot (max. 60°) or cold water supply.
With a hot water supply you can have a sig-
nificant reduction of energy consumption.
This however, depends on how the hot water
is produced. (We suggest alternative sources
of energy that are more environmentally
friendly as e.g. solar or photovoltaic panels
and aeolian).
For making the connection itself, the cou-
pling nut fitted to the appliance water inlet
hose is designed to screw onto a 3/4 thread
spout or to a purpose made quick-coupling
tap such as the Press-block.
The water pressure must be within the limits
given in the Technical data. Your local Wa-
ter Authority will advise you on the average
mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being con-
nected.
The appliance features inlet and drain hoses
which can be turned either to the left or the
right to suit the installation by means of the
locknut. The locknut must be correctly
fitted to avoid water leaks.
Attention! NOT all dishwasher models of
have inlet and drain hoses provided with
a locknut. In this case, this facility is not
available.If the appliance is connected to new pipes or
pipes which have not been used for a long
time, you should run the water for a few mi-
nutes before connecting the inlet hose.
DO NOT use connection hoses which
have previously been used on an old ap-
pliance.
This appliance has been fitted with safe-
ty features which will prevent the water
used in the appliance from returning
back into the drinking water system. This
appliance complies with the applicable
plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water in-
let hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the wa-
ter inlet hose starts to leak during this oper-
ation, the safety valve cuts off the running
water.
Please take care when installing the water
inlet hose:
• The electrical cable for the safety valve is
in the double-walled water inlet hose. Do
not immerse the water inlet hose or the
safety valve in water.
• If water inlet hose or the safety valve is
damaged, remove the mains plug imme-
diately.
22  electrolux
 
						

							• A water inlet hose with safety valve must
only be replaced by the Service Force
Centre.
Warning! Dangerous voltage
Water drain connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink run-
ning into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
The waste connection must be at a maxi-
mum height of 60 cm from the bottom of the
dishwasher.
The drain hose can face either to the right or
left of the dishwasher
Ensure the drain hose is not bent or squash-
ed as this could prevent or slow down the
discharge of water.
The sink plug must not be in place when the
machine is draining as this could cause the
water to syphon back into the machine.
The total length of the drain hose, including
any extension you might add, must be no
longer than 4 metres. The internal diameter
of the extension hose must be no smaller
than the diameter of the hose provided.
Likewise the internal diameter of the cou-
plings used for connections to the waste out-
let must be no smaller than the diameter of
the hose provided.
When connecting the drain hose to an under
sink trap spigot, the entire plastic mem-
brane (A) must be removed. Failure to re-
move all the membrane will result in food
particles building up over time eventually
blocking the dishwasher drain hose spigot
Our appliances are supplied with a se-
curity device to protect against the re-
turn of dirty water back into the machine.
If the spigot of your sink has a no return
valve incorporated this can prevent the
correct draining of your dishwasher. We
therefore advise you to remove it.
To avoid water leakage after installation
make sure that the water couplings are
tight.
Electrical connection
Warning! Safety standards require
the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated volt-
age and type of supply on the ratingplate match that of the supply where
the appliance is to be installed. The
f u se  r a t in g  i s a l so  t o b e  f o un d  o n t h e
rating plate.
electrolux  23
 
						

							Always plug the mains plug into a
correctly installed shockproof sock-
et.
Multi-way plugs, connectors and ex-
tension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic wir-
ing system socket replaced. In case
that the electrical cable has to bereplaced, contact your local Service
Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by pull-
ing on the cable. Always pull the
plug.
The manufacturer accepts no liabil-
ity for failure to observe the above
safety precautions.
Environment concerns
The symbol    on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PEPS
						

							electrolux  25
 
						

							26  electrolux
 
						

							electrolux  27
 
						

							117958370 - 00 - 112008
www.electrolux.com