Electrolux Esl 66010 User Manual

something not working electrolux  31
Malfunction Possible cause and solution
The programme does not startThe dishwasher’s door has not been
properly closed. 
Close the door.
The main plug is not plugged in. 
Insert the main plug.
Delay start has been set. 
If dishes are to be washed immediately,
cancel the delay start.
The fuse has blown out in the household
fuse box. 
Replace the fuse.
Once these checks have been carried
out; switch on the appliance, press
the button of the programme that was...

32electroluxsomething not working
If after all these checks, the problem
persists, contact your local Service
Force Centre.The wash results are not satisfactory
The dishes are not
cleanThe wrong washing programme has been selected.
The dishes are arranged in such a way as to stop water
reaching all parts of the surface. The baskets must not
be overloaded.
The spray arms do not rotate freely due to incorrect
arrangement of the load.
The filters in the base of the washing compartment are
dirty or...

technical data electrolux  33
Technical data
Dimensions Width 59.6 cm
81.8 - 87.8 cm
55.5 cm Height
Depth
Water supply pressure Minimum 0.05 MPa (0.5 bar)
0.8 MPa (8 bar) Maximum
Capacity12 place settings
Max. weight38.5 kg
Noise level45 dB (A)
Electrical connection
Voltage - Overall power -
FuseInformation on the electrical connection is given
on the rating plate on the inner edge of the
dishwasher’s door
Subject to change without notice
117989 83/0en  20-02-2007  17:34  Pagina 33
 

34electroluxtechnical data
Consumption values
Programme
duration 
(in minutes)Programme Energy
consumption 
(in kWh)Water
consumption 
(in litres)
*Intensive1.8 - 2.023 - 25
*Auto1.1 - 1.512 - 23
*Quick0.99
*
Eco
(Test programme
for test institutes)1.0515
*Rinse and
Hold0.14
The consumption values are intended
as a guide and depends on the
pressure and the temperature of the
water and also by the variations of the
power supply and the amount of
dishes.
*The programme duration is visible
in the digital...

hints for test instituteselectrolux  35
Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance
fully loaded and using the test
programme (see Consumption
values).Test in accordance with EN 50242
must be carried out when the salt
container and rinse aid dispenser
have been filled with salt and rinse aid
respectively and using the test
programme (see Consumption
values).
Arrangement upper basket
Arrangement lower basket
Arrangement cutlery
basket
Full load:
12...

36electroluxinstallation
Any electrical and/or plumbing
work required to install this
appliance should be carried out by
a qualified electrician and/or
plumber or competent person.
Remove all packaging before
positioning the machine.
If possible, position the machine next
to a water tap and a drain.
This dishwasher is designed to be
fitted under a kitchen counter or
worksurface.
Attention! Carefully follow the
instructions on the enclosed template
for building in the dishwasher and
fitting the furniture...

installation electrolux  37
Water supply connections 
This dishwasher may be fed with
either hot (max. 60°) or cold water.
Nevertheless we advise you a cold
water supply.
A hot water supply is not always
efficient with very soiled crockery as it
shortens the washing programmes a
lot.
For making the connection itself, the
coupling nut fitted to the machine’s
supply hose is designed to screw onto
a 3/4 gas thread spout or to a
purpose made quick-coupling tap
such as the Press-block.
The water pressure must...

38electroluxinstallation
Water inlet hose with safety valve
After connecting the double-walled
water inlet hose, the safety valve is
next to the tap. Therefore the water
inlet hose is only under pressure
while the water is running. If the water
inlet hose starts to leak during this
operation, the safety valve cuts off the
running water.
Please take care when installing the
water inlet hose:
The electrical cable for the safety
valve is in the double-walled water
inlet hose. Do not immerse the
water inlet...

installation electrolux  39
Water outlet hose connection
The end of the drain hose can be
connected in the following ways: 
1. To the sink outlet spigot, securing
it to the underside of the work
surface. This will prevent waste
water from the sink running into
the machine. 
2. To a stand pipe provided with vent-
hole, minimum internal diameter 4
cm. 
The waste connection must be at a
maximum height of 60 cm from the
bottom of the dishwasher. 
The drain hose can face either to the
right or left of the...

40electroluxinstallation
Electrical connection
Safety standards require the
appliance to be earthed. 
Prior to using the appliance for the
first time, ensure that the rated
voltage and type of supply on the
rating plate match that of the
supply where the appliance is to be
installed. The fuse rating is also to
be found on the rating plate.
Always plug the mains plug into a
correctly installed shockproof
socket.
Multi-way plugs, connectors and
extension cables must not be used.
This could constitute a...