Electrolux Esf 66840 User Manual

							Arrangement upper basket
Arrangement lower basket
Arrangement cutlery basket
Installation
Warning! Any electrical and/or
plumbing work required to install
this appliance should be carried out
by a qualified electrician and/or
plumber or competent person.
Fitting under a counter (kitchen worktop
or sink)
Remove all packaging before positioning the
machine.
If possible, position the machine next to a
water tap and a drain.
By removing the machines worktop, you can
install it under a close fitting sink unit or a pre-
existing top, providing the dimensions of therecess correspond to those shown in the
picture.
electrolux  21
 
						

							Proceed as follows:
• Remove the machine’s worktop by un-
screwing the two rear retaining screws (1),
pull the worktop from the back of the ma-
chine (2) and slide out the front slots, lifting
the worktop (3).Insert the machine after adjusting the level-
ling with the adjustable feet. When inserting
the machine, ensure that the water inlet and
drain hoses are not kinked or squashed.
During all operations that involve accessibility
to internal components the dishwasher has
to be unplugged.
Be sure that once the appliance has been in-
stalled, it is easily accessible for the service
engineer in the event that a repair is required.
If the dishwasher is later used as a free-
standing appliance, the original worktop
must be re-mounted.
The plinth on free-standing appliances is not
adjustable.
Levelling
Good levelling is essential for correct closure
and sealing of the door.
When the appliance is correctly levelled, the
door will not catch on either side of the cab-
inet .
If the door does not close correctly, loosen
or tighten the adjustable feet until the ma-
chine is perfectly level.
Water connection
Water inlet connection
This appliance can be connected to either a
hot (max. 60°) or cold water supply.
With a hot water supply you can have a sig-
nificant reduction of energy consumption.
This however, depends on how the hot water
is produced. (We suggest alternative sources
of energy that are more environmentally
friendly as e.g. solar or photovoltaic panels
and aeolian).
For making the connection itself, the cou-
pling nut fitted to the appliance water inlet
hose is designed to screw onto a 3/4 thread
spout or to a purpose made quick-coupling
tap such as the Press-block.
The water pressure must be within the limits
given in the Technical data. Your local Wa-
ter Authority will advise you on the average
mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being con-
nected.
The locknut must be correctly fitted to avoid
water leaks.
If the appliance is connected to new pipes or
pipes which have not been used for a longtime, you should run the water for a few mi-
nutes before connecting the inlet hose.
Do not use connection hoses which
have previously been used on an old ap-
pliance.
This appliance has been fitted with safe-
ty features which will prevent the water
used in the appliance from returning
back into the drinking water system. This
appliance complies with the applicable
plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water in-
let hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the wa-
ter inlet hose starts to leak during this oper-
ation, the safety valve cuts off the running
water.
Please take care when installing the water
inlet hose:
22  electrolux
 
						

							• The electrical cable for the safety valve is
in the double-walled water inlet hose. Do
not immerse the water inlet hose or the
safety valve in water.
• If water inlet hose or the safety valve is
damaged, remove the mains plug imme-
diately.
• A water inlet hose with safety valve must
only be replaced by the Service Force
Centre.
Warning! Dangerous voltage
Water drain connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink run-
ning into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
max 85 cm
min 40 cm
max 400 cm
The drain hose can face either to the right or
left of the dishwasher
Ensure the drain hose is not bent or squash-
ed as this could prevent or slow down the
discharge of water.
The sink plug must not be in place when the
machine is draining as this could cause the
water to syphon back into the machine.
If you use a drain hose extension, its internal
diameter must be no smaller than the diam-
eter of the hose provided.
Likewise the internal diameter of the cou-
plings used for connections to the waste out-
let must be no smaller than the diameter of
the hose provided.
When connecting the drain hose to an under
sink trap spigot, the entire plastic mem-
brane (A) must be removed. Failure to re-
move all the membrane will result in food
particles building up over time eventually
blocking the dishwasher drain hose spigot
Our appliances are supplied with a se-
curity device to protect against the re-
turn of dirty water back into the machine.
If the spigot of your sink has a no return
valve incorporated this can prevent the
correct draining of your dishwasher. We
therefore advise you to remove it.
To avoid water leakage after installation
make sure that the water couplings are
tight.
Electrical connection
Warning! Safety standards require
the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated volt-
age and type of supply on the rating
plate match that of the supply where
the appliance is to be installed. The
f u s e  ra t i n g i s a l so  t o  be  f o u n d o n  t h e
rating plate.Always plug the mains plug into a
correctly installed shockproof sock-
et.
Multi-way plugs, connectors and ex-
tension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic wir-
ing system socket replaced. In case
that the electrical cable has to be
electrolux  23
 
						

							replaced, contact your local Service
Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by pull-
ing on the cable. Always pull the
plug.The manufacturer accepts no liabil-
ity for failure to observe the above
safety precautions.
Environment concerns
The symbol    on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PEPS
						

							electrolux  25
 
						

							26  electrolux
 
						

							electrolux  27
 
						

							117956290 - 00 - 122008
www.electrolux.com