Electrolux Esf 66030 User Manual

							care and cleaning electrolux  31
Prolonged periods of non-
operation 
If you are not using the machine for
any period of time you are advised to: 
1. Unplug the appliance and then
turn off the water. 
2. Leave the door ajar to prevent the
formation of any unpleasant
smells. 
3. Leave the inside of the machine
clean. 
Frost precautions 
Avoid placing the machine in a
location where the temperature is
below 0°C. If this is unavoidable,
empty the machine, close the
appliance door, disconnect the water
inlet pipe and empty it. 
Moving the machine 
If you have to move the machine
(moving house etc....): 
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and
discharge hoses.
4. Pull the machine out together with
the hoses. 
Avoid over tilting the machine during
transportation. 
NEVER try to remove the upper
spray arm.
If residues of soil have clogged the
holes in the upper spray arm, remove
them with a cocktail stick.
External cleaning
Clean the external surfaces of the
machine and control panel with a
damp soft cloth. If necessary use only
neutral detergents. Never use
abrasive products, scouring pads or
solvent (acetone, trichloroethylene
etc....). 
Ensure that the seals around the
door, the detergent and rinse aid
dispensers are cleaned regularly with
a damp cloth.
We recommend every 3 months to
run a 65°C wash programme without
dishes using detergent.
117998 54/0en  1-06-2006  11:01  Pagina 31
 
						

							The dishwasher will not start or stops during operation. 
Certain problems are due to the lack of simple maintenance or oversights,
which can be solved with the help of the indications described in the chart,
without calling out an engineer.
Switch off the dishwasher, open the door and carry out the following suggested
corrective actions.
Something not working
Fault codeMalfunction Possible cause Solution
continuous flashing
of the light of the
running
programme
appears in
the digital display
The dishwasher
does not fill with
waterThe water tap is
blocked or furred
with limescale
The water inlet
hose has not been
correctly laid or it
is bent or
squashed
The filter (where
present) in the
threaded hose
fitting at the water
inlet valve is
blocked
The water tap is
turned off
Check the water
drain hose
connection
Turn the water tap
on
Clean the filter in
the threaded hose
Clean the water
tap
continuous flashing
of the light of the
running
programme
appears in
the digital display
The dishwasher will
not drainThe sink spigot is
blocked
The water drain
hose has not been
correctly laid or it
is bent or
squashed
Clean out the sink
spigot
Check the water
drain hose
connection
continuous flashing
of the light of the
running
programme
appears in
the digital display
Anti-flood device is
activatedClose the water
tap and contact
your local Service
Force Centre
32electroluxcare and cleaning
117998 54/0en  1-06-2006  11:01  Pagina 32
 
						

							something not working electrolux  33
Fault codeMalfunction Possible cause Solution
The programme
does not startThe dishwasher’s
door has not been
properly closed
The main plug is
not plugged in
Delay start has
been set
The fuse has
blown out in the
household fuse
box
Close the door
Replace the fuse
Insert the main
plug
If dishes are to be
washed
immediately,
cancel the delay
start
Once these checks have been carried
out; close the dishwasher’s door and
switch on the appliance. Press the
button of the programme that was
running before the intervention of the
alarm. The programme will continue
from the point at which it was
interrupted. 
If the malfunction or fault code
reappears contact the Service Force
Centre. 
For other  fault codes not described in
the above chart, please contact your
Service Force Centre.Contact your local Service Force
Centre, quoting the model (Mod.),
product number (PNC) and serial
number (S.N.). 
This information can be found on the
rating plate located on the side of the
dishwasher door.
So that you always have these
numbers at hand, we recommend you
to make a note of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . 
PNC :. . . . . . . . . . . . . . . . . . . . . . . . 
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . 
117998 54/0en  1-06-2006  11:01  Pagina 33
 
						

							34electroluxsomething not working
If after all these checks, the problem
persists, contact your local Service
Force Centre.The wash results are not satisfactory
The dishes are not
clean
The wrong washing programme has been
selected.
The dishes are arranged in such a way as to stop
water reaching all parts of the surface. The
baskets must not be overloaded.
The spray arms do not rotate freely due to
incorrect arrangement of the load.
The filters in the base of the washing compartment
are dirty or incorrectly positioned.
Too little or no detergent has been used.
Where there are limescales deposits on the
dishes; the salt container is empty or the incorrect
level of the water softener has been set.
The drain hose connection is not correct.
The salt container cap is not properly closed.
The dishes are wet and
dullRinse aid was not used.
The rinse aid dispenser is empty.
There are streaks,
milky spots or a bluish
coating on glasses and
dishesDecrease rinse aid dosing.
Water drops have dries
onto glasses and
dishesIncrease rinse aid dosing.
The detergent may be the cause. Contact the
detergent manufacturer’s consumer care line.
117998 54/0en  1-06-2006  11:01  Pagina 34
 
						

							technical data electrolux  35
Technical data
Dimensions Width 60 cm
85 cm
63.5 cm Height
Depth
Water supply pressure Minimum 0,05 MPa
0,8 MPa Maximum
Capacity12 place settings
Max. weight42 kg
Noise level45 dB (A)
Electrical connection
Voltage - Overall power -
FuseInformation on the electrical connection is given
on the rating plate on the inner edge of the
dishwasher’s door
Subject to change without notice
117998 54/0en  1-06-2006  11:01  Pagina 35
 
						

							36electroluxtechnical data
The consumption values are intended
as a guide and depends on the
pressure and the temperature of the
water and also by the variations of the
power supply and the amount of
dishes.
Consumption values
Programme
duration 
(in minutes)Programme Energy
consumption 
(in kWh)Water
consumption 
(in litres)
*Intensive1,7 - 1,923 - 25
*Auto1,1 - 1,512 - 25
*Quick0,89
*
Eco
(Test programme
for test institutes)1,0515
*Glass0,8 - 0,914 - 16
*The programme duration is visible
in the digital display when the
washing programme is selected.
117998 54/0en  1-06-2006  11:01  Pagina 36
 
						

							hints for test institutes electrolux  37
Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance
fully loaded and using the test
programme (see Consumption
values).Test in accordance with EN 50242
must be carried out when the salt
container and rinse aid dispenser
have been filled with salt and rinse aid
respectively and using the test
programme (see Consumption
values).
Arrangement upper basket
(take of the glass holder)
Arrangement lower basket
Arrangement cutlery
basket
Full load:
12 standard place settings
Amount of detergent required:5 g + 25 g (Type B)
Rinse aid setting:position 4 (Type III)
117998 54/0en  1-06-2006  11:01  Pagina 37
 
						

							38electroluxinstallation
Any electrical and/or plumbing
work required to install this
appliance should be carried out by
a qualified electrician and/or
plumber or competent person.
Remove all packaging before
positioning the machine.
If possible, position the machine next
to a water tap and a drain.
Fitting under a counter 
(kitchen worktop or sink)
By removing the machine’s worktop,
you can install it under a close fitting
sink unit or a pre-existing top,
providing the dimensions of the
recess correspond to those shown in
the picture.
Installation
Proceed as follows:
Remove the machine’s worktop by
unscrewing the two rear retaining
screws, pull the worktop from the
back of the machine and slide out
the front slots, lifting the worktop.
Insert the machine after adjusting the
levelling with the adjustable feet.
When inserting the machine, ensure
that the water inlet and drain hoses
are not kinked or squashed.
During all operations that involve
accessibility to internal components
the dishwasher has to be unplugged.
Be sure that once the appliance has
been installed, it is easily accessible
for the service engineer in the event
that a repair is required.
If the dishwasher is later used as a
free-standing appliance, the original
worktop must be re-mounted.
The plinth on free-standing appliances
is not adjustable.
117998 54/0en  1-06-2006  11:01  Pagina 38
 
						

							installation electrolux  39
Levelling
Good levelling is essential for correct
closure and sealing of the door.
When the appliance is correctly
levelled, the door will not catch on
either side of the cabinet.
If the door does not close correctly,
loosen or tighten the adjustable feet
until the machine is perfectly level.
Water supply connections 
This dishwasher may be fed with
either hot (max. 60°) or cold water.
Nevertheless we advise you a cold
water supply.
A hot water supply is not always
efficient with very soiled crockery as it
shortens the washing programmes a
lot.
For making the connection itself, the
coupling nut fitted to the machine’s
supply hose is designed to screw onto
a 3/4 gas thread spout or to a
purpose made quick-coupling tap
such as the Press-block.
The water pressure must be within
the limits given in the Technical
specifications. Your local Water
Authority will advise you on the
average mains pressure in your area. 
The water inlet hose must not be
kinked, crushed, or entangled when it
is being connected. 
The dishwasher features fill and drain
hoses which can be turned either to
the left or the right to suit the
installation by means of the locknut.
The locknut must be correctly fitted
to avoid water leaks.
(Attention! NOT all models of
dishwashers have fill and drain hoses
provided with locknut. In this case,
this kind of facility is not possible).If the machine is connected to new
pipes or pipes which have not been
used for a long time, you should run
the water for a few minutes before
connecting the inlet hose. 
DO NOT use connection hoses
which have previously been used
for an old appliance.
This appliance has been fitted with
safety features which will prevent the
water used in the appliance from
returning back into the drinking water
system. This appliance complies with
the applicable plumbing regulations.
117998 54/0en  1-06-2006  11:01  Pagina 39
 
						

							Water inlet hose with safety valve
After connecting the double-walled
water inlet hose, the safety valve is
next to the tap. Therefore the water
inlet hose is only under pressure
while the water is running. If the water
inlet hose starts to leak during this
operation, the safety valve cuts off the
running water.
Please take care when installing the
water inlet hose:
The electrical cable for the safety
valve is in the double-walled water
inlet hose. Do not immerse the
water inlet hose or the safety valve
in water.
If water inlet hose or the safety
valve is damaged, remove the
mains plug immediately.
A water inlet hose with safety valve
must only be replaced by a
specialist or by the Service Force
Centre.
Place the water inlet hose in such
a way that it is never higher than
the bottom edge of the safety
valve.
40electroluxinstallation
Warning!
Dangerous voltage
117998 54/0en  1-06-2006  11:01  Pagina 40