Electrolux Esf 45010 S User Manual

							something not working electrolux  31
Malfunction Possible cause and solution
The programme does not startThe dishwasher’s door has not been
properly closed.
Close the door.
The main plug is not plugged in.
Insert the main plug.
Delay start has been set.
If dishes are to be washed immediately,
cancel the delay start.
The fuse has blown out in the household
fuse box.
Replace the fuse.
Once these checks have been carried
out switch on the appliance. 
The programme will continue from the
point at which it was interrupted. 
If the malfunction or fault code
reappears contact the Service Force
Centre. 
For other fault codes not described in
the above chart, please contact your
Service Force Centre.
Contact your local Service Force
Centre, quoting the model (Mod.),
product number (PNC) and serial
number (S.N.). 
This information can be found on the
rating plate located on the side of the
dishwasher door.
So that you always have these
numbers at hand, we recommend you
to make a note of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . 
PNC :. . . . . . . . . . . . . . . . . . . . . . . . 
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . 
117997 87/1en  2-05-2007  11:32  Pagina 31
 
						

							32electroluxsomething not working
If after all these checks, the problem
persists, contact your local Service
Force Centre.
The wash results are not satisfactory
The dishes are not cleanThe wrong washing programme has been selected.
The dishes are arranged in such a way as to stop water
reaching all parts of the surface. The baskets must not
be overloaded.
The spray arms do not rotate freely due to incorrect
arrangement of the load.
The filters in the base of the washing compartment are
dirty or incorrectly positioned.
Too little or no detergent has been used.
Where there are limescales deposits on the dishes; the
salt container is empty or the incorrect level of the water
softener has been set.
The drain hose connection is not correct.
The salt container cap is not properly closed.
The dishes are wet and
dullRinse aid was not used.
The rinse aid dispenser is empty.
There are streaks, milky
spots or a bluish coating
on glasses and dishesDecrease rinse aid dosing.
Water drops have dries
onto glasses and dishesIncrease rinse aid dosing.
The detergent may be the cause. Contact the detergent
manufacturer’s consumer care line.
117997 87/1en  2-05-2007  11:32  Pagina 32
 
						

							technical dataelectrolux  33
Technical data
Dimensions Width 45 cm
85 cm
63 cm Height
Depth
Water supply pressure Minimum 0.05 MPa
0.8 MPa Maximum
Capacity9 place settings
Max. weight37 kg
Electrical connection
Voltage - Overall power -
FuseInformation on the electrical connection is given
on the rating plate on the inner edge of the
dishwasher’s door
Subject to change without notice
117997 87/1en  2-05-2007  11:32  Pagina 33
 
						

							34electroluxtechnical data
The consumption values are intended
as a guide and depends on the
pressure and the temperature of the
water and also by the variations of the
power supply and the amount of
dishes.
Consumption values
Programme
duration 
(in minutes)Programme Energy
consumption 
(in kWh)Water
consumption 
(in litres)
105 - 115Intensive1.6 - 1.819 - 21
80 - 105Auto0.8 - 1.212 - 21
25 - 30Quick0.7 - 0.87 - 8
160Eco
(Test programme
for test institutes)0.813
55 - 65Glass0.6 - 0.711 - 12
117997 87/1en  2-05-2007  11:32  Pagina 34
 
						

							hints for test institutes electrolux  35
Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance
fully loaded and using the test
programme (see Consumption
values).Test in accordance with EN 50242
must be carried out when the salt
container and rinse aid dispenser
have been filled with salt and rinse aid
respectively and using the test
programme (see Consumption
values).
Full load: 9 standard place settings
Amount of detergent required:5 g + 20 g (Type B)
Rinse aid setting:position 4 (Type III)
Arrangement upper basket
Cup racks: position AArrangement cutlery
basketArrangement lower
basket
117997 87/1en  2-05-2007  11:32  Pagina 35
 
						

							36electroluxinstallation
Installation
Any electrical and/or plumbing
work required to install this
appliance should be carried out by
a qualified electrician and/or
plumber or competent person.
Remove all packaging before
positioning the machine.
If possible, position the machine next
to a water tap and a drain.
Fitting under a counter 
(kitchen worktop or sink)
By removing the machine’s worktop,
you can install it under a close fitting
sink unit or a pre-existing top,
providing the dimensions of the
recess correspond to those shown in
the picture.
Proceed as follows:
Remove the machine’s worktop by
unscrewing the two rear retaining
screws, pull the worktop from the
back of the machine and slide out
the front slots, lifting the worktop.
Insert the machine after adjusting the
levelling with the adjustable feet.
When inserting the machine, ensure
that the water inlet and drain hoses
are not kinked or squashed.
During all operations that involve
accessibility to internal components
the dishwasher has to be unplugged.
Be sure that once the appliance has
been installed, it is easily accessible
for the service engineer in the event
that a repair is required.
If the dishwasher is later used as a
free-standing appliance, the original
worktop must be re-mounted.
The plinth on free-standing appliances
is not adjustable.
Levelling
Good levelling is essential for correct
closure and sealing of the door.
When the appliance is correctly
levelled, the door will not catch on
either side of the cabinet.
If the door does not close correctly,
loosen or tighten the adjustable feet
until the machine is perfectly level.
117997 87/1en  2-05-2007  11:32  Pagina 36
 
						

							installation electrolux  37
This appliance has been fitted with
safety features which will prevent the
water used in the appliance from
returning back into the drinking water
system. This appliance complies with
the applicable plumbing regulations.
Water supply connections 
This dishwasher may be fed with
either hot (max. 60°) or cold water.
Nevertheless we advise you a cold
water supply.
A hot water supply is not always
efficient with very soiled crockery as it
shortens the washing programmes a
lot.
For making the connection itself, the
coupling nut fitted to the machine’s
supply hose is designed to screw onto
a 3/4 gas thread spout or to a
purpose made quick-coupling tap
such as the Press-block.
The water pressure must be within
the limits given in the Technical
specifications. Your local Water
Authority will advise you on the
average mains pressure in your area. 
The water inlet hose must not be
kinked, crushed, or entangled when it
is being connected. 
The dishwasher features fill and drain
hoses which can be turned either to
the left or the right to suit the
installation by means of the locknut.
The locknut must be correctly fitted
to avoid water leaks.
(Attention! NOT all models of
dishwashers have fill and drain hoses
provided with locknut. In this case,
this kind of facility is not possible).
If the machine is connected to new
pipes or pipes which have not been
used for a long time, you should run
the water for a few minutes before
connecting the inlet hose. 
DO NOT use connection hoses
which have previously been used
for an old appliance.
117997 87/1en  2-05-2007  11:32  Pagina 37
 
						

							38electroluxinstallation
Water inlet hose with safety valve
After connecting the double-walled
water inlet hose, the safety valve is
next to the tap. Therefore the water
inlet hose is only under pressure
while the water is running. If the water
inlet hose starts to leak during this
operation, the safety valve cuts off the
running water.
Please take care when installing the
water inlet hose:
The electrical cable for the safety
valve is in the double-walled water
inlet hose. Do not immerse the
water inlet hose or the safety valve
in water.
If water inlet hose or the safety
valve is damaged, remove the
mains plug immediately.
A water inlet hose with safety valve
must only be replaced by the
Service Force Centre.
Place the water inlet hose in such
a way that it is never higher than
the bottom edge of the safety
valve.
Warning!
Dangerous voltage
117997 87/1en  2-05-2007  11:32  Pagina 38
 
						

							installation electrolux  39
Water outlet hose connection
The end of the drain hose can be
connected in the following ways: 
1. To the sink outlet spigot, securing
it to the underside of the work
surface. This will prevent waste
water from the sink running into
the machine. 
2. To a stand pipe provided with vent-
hole, minimum internal diameter 4
cm. 
The waste connection must be at a
height of between 30 cm (minimum)
and 100 cm (maximum) from the
bottom of the dishwasher. 
The drain hose can face either to the
right or left of the dishwasher 
Ensure the hose is not bent or
squashed as this could prevent or
slow down the discharge of water. 
The sink plug must not be in place
when the machine is draining as this
could cause the water to syphon back
into the machine. 
If you use a drain hose extension it
must be no longer than 2 metres and
its internal diameter must be no
smaller than the diameter of the hose
provided. 
Likewise the internal diameter of the
couplings used for connections to the
waste outlet must be no smaller than
the diameter of the hose provided. 
Our appliances are supplied with a
security device to protect against the
return of dirty water back into the
machine. 
If the spigot of your sink has a no
return valve incorporated this can
prevent the correct draining of your
dishwasher. We therefore advise you
to remove it.
When connecting the drain hose to an
under sink trap spigot, the entire
plastic membrane (A) must be
removed. Failure to remove all the
membrane will result in food particles
building up over time eventually
blocking the dishwasher drain hose
spigot
117997 87/1en  2-05-2007  11:32  Pagina 39
 
						

							40electroluxinstallation
Electrical connection
Safety standards require the
appliance to be earthed. 
Prior to using the appliance for the
first time, ensure that the rated
voltage and type of supply on the
rating plate match that of the
supply where the appliance is to be
installed. The fuse rating is also to
be found on the rating plate.
Always plug the mains plug into a
correctly installed shockproof
socket.
Multi-way plugs, connectors and
extension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic
wiring system socket replaced. In
case that the electrical cable has to
be replaced, contact your local
Service Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by
pulling on the cable. Always pull
the plug.
The manufacturer accepts no
liability for failure to observe the
above safety precautions.
117997 87/1en  2-05-2007  11:32  Pagina 40