Electrolux Esf 2440 Instruction Book

							- 11 -
This appliance complies with the following E.E.C. directives:
Ð 73/23/EEC, dated 19.02.1973 Ð low-voltage directive.
Ð 89/336/EEC, dated 03.05.1989 (incl. amendment
Ð 92/31/EEC) Ð directive on electromagnetic compatibility.
Indicator for the selected programme
ßashes:
The display shows error code   , 10.
(Problems with the water supply).¥ Is the water tap turned on?
¥ Is the Þlter inside the inlet hose blocked?
¥ Is the water inlet hose kinked or squashed?
¥ Are the Þlters clogged?
Fault Check
Indicator for the selected programme
ßashes:
The display shows error code   , 20.
(Problems with water drainage).¥ Is the spigot blocked?
¥ Is the water drain hose kinked or squashed?
¥ Are the Þlters clogged?
In the event of a fault
With help of the error code on the display, itÕs possible that you can solve the problem yourself. When the problem is
solved, press in the button for the disrupted programme and the programme continues. 
For other error codes on the display (  , followed by a numbers):
¥ Interruptthe dishwashing cycle.
¥ Switch the dishwasher off.
¥ Select the relevant programme again.
If the problem occurs again, contact your local service centre, stating the error code. 
 
						

							- 12 -
Service
Service and spare parts
Servicing and repairs must be carried out by a service
company authorised by the supplier. Use only spare
parts supplied by these. 
Before calling service, use the trouble shooting table 
ÓIn  the event of a faultÓ to try to attend to the fault yourself.
Note that electrical faults shall always be rectiÞed by a
certiÞed electrician.
State the applianceÕs model designation, product- and
serial numbers according to the data plate afÞxed to the
rear of the dishwasher.
You can record these details here:
TYPE. ............................................................
MOD. ............................................................
PROD.NO. ............................................................
SER.NO. ............................................................
Purchase date ............................................................
Under what circumstances does the fault occur?
Never attempt to repair the dishwasher yourself. 
Repairs carried out by unauthorised or inexperienced
persons can cause injury or serious malfunctioning.
The salt container and rinse aid dispenser shall be Þlled in accordance with this instruction manual. 
Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using
detergent and a clean load.
Test standard: EN 50242 and EN 60704
Rated capacity: 6 place settings accordance EN 50242
Loading of basket: see chapter ÓLoading the dishesÓ
Test program: energy saving 55¡ C
Detergent (IEC type B): 9 gram in the dispenser + 5 gram in the pre-wash dispenser
Rinse aid (type III): setting 3
Feed water pressure: minimum 0,8 bar, maximum 10 bar
Waste water outlet: install according to Þgure below
Information for test centres
 
						

							- 13 -
Installation instructions
Any electrical work required to install this appliance,
should be carried out by a qualiÞed electrician or
competent person.
Any plumbing work required to install this appliance,
should be carried out by a qualiÞed plumber or
competent person.
Technical speciÞcations
Capacity:6 place settings accordance EN 50242
Dimensions:Height 447 mm
Width 546 mm
Depth (to the edge of the door) 480 mm
Depth (to the middle of the door) 507 mm
Weight:Net 22 kg
Water pressures:Minimum 80 kPa (0,8 bar)
Maximum 1000 kPa (10 bar)
Water temperature:Maximum 65¡ C
Electrical data:Power supply 230 V - 50 Hz
Fuse 10 A
Heating element 1100 W
Power rating 1180 W
 
						

							- 14 -
Unpacking
Damages
If the dishwasher has been damaged during transport,
you should immediately notify the company responsible
for delivering it.
Check that the dishwasher is undamaged. If you discover
any damage, faults or that anything is missing, you should
notify the dealer immediately.
Never leave packaging material in a place
where children may play with it.
Check that the following accessories are supplied with the
dishwasher when you unpack it:
Ð Elbow for discharge hose
Use
This dishwasher is designed solely for washing household
utensils suitable for washing in a dishwasher.Using it for
other purposes may damage it and invalidatethe guarantee.
Positioning
The dishwasher is intended to be installed on a kitchen
drainer, worktop or built-in. To function properly, make
sure that the appliance is level. Its height can be adjusted
with the adjustable feets (5 mm each). See the illustration
for built-in measurements.
Protecting the dishwasher against
freezing
If the dishwasher is placed in an environment
where the temperature sometimes fall below 
0¡ C, there is a risk that the small amount of
water which remains inside the parts of the
dishwasher will freeze and damage it. 
To prevent this you should:
1. Turn off the water supply to the dishwasher.
2. Remove the water inlet and discharge hoses.
The appliance is only to be used and stored indoors
at normal room temperature. The manufacture is
not responsible for any frost damage.
 
						

							- 15 -
Installation
Water inlet
The dishwasher is equipped with safety features
which are to prevent the water from going back 
to the fresh water system. These features are ac-
cording to current water technical safety regulations.
The temperature of the water supply should not exceed 65¡ C
and the pressure should be between 80-1000 kPa (0,8 - 10 bar). 
It is important to have a tap or stopcock, positioned close to
the dishwasher and with easy access. Special mixer taps with
dishwasher connections are available, as well as adaptors
for older mixer taps. Connect the inlet hose  to a tap with a
3/4 pipe thread. If necessary, use the restrictor (1/2Ó) supplied.
The inlet hose must not be joined onto any form of extension
hose. If it is too short, the entire hose must be replaced with
a longer high-pressure hose, specially designed for the
purpose. The end of the hose, which is connected to the
dishwasher can be turned in any direction. Loosen the
retaining nut, turn the hose, then retighten the nut.
Check that the nut and all other connections are
tight before the machine is moved into position.
Use only the inlet hose supplied to the dish-
washer, do not reuse the old inlet hose.
Water drainage
To protect the dishwasher against water damage it is
equipped with a water safety system. In the event of
a fault the drain-pump starts automatically and the
remaining water inside the dishwasher is pumped out.
The water safety system also works when the
dishwasher is switched off. However the dish-
washer must be connected electrically. 
Place the discharge hose over the sink as illustrated.
It must not at any point be higher up than 75 cm over the
surface which the dishwasher is standing on. If it runs
higher, operation of the dishwasher might be impaired. 
It is also important to ensure that the inside diameter of the
hose is not less than 13 mm at any point. If the discharge
hose is too long, it can easily be cut to the right length.
1. Cut the hose to a suitable length, using a sharp 
knife.
2. Fit the elbow supplied onto the end of the hose.
Electrical connection
The dishwasher is supplied with a lead and electrical plug
for connection to a 230 V earthed wall socket, which should
be easily accessible and protected by a 10 A fuse.
Before any work is carried out on the dishwasher,
it must be isolated from the electric mains supply,
for example by removing the plug from the wall
socket.
Permanent electrical installation must be carried
out by an authorised electrician or competent
person.
 
						

							Technical changes possible