Eizo Foris Fs2332 Users Manual

31Chapter3SettingMonitor
3-6. Setting the EIZO Logo Display “Logo”
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to display or not to 
display the EIZO logo.Procedure
1.
 
C
 hoose “Monitor Settings” in the Setting menu, and press 
.
2.
 
C

hoose “Logo” in the “Monitor Settings” menu, and press 
.
The “Logo” menu appears.
3. Select “On” or “Off ” with  or .
4.
 
P

ress 
 to exit the adjustment.
3-7. Setting Language “Language”
This function allows you to select a...

32Chapter3SettingMonitor
3-9. Resetting the Monitor to the Default Settings
There are two different Resets: Color Reset for only resetting the color adjustments to the default settings and 
Full Reset for resetting all settings to the defaults.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings” (page 45).
 ●To reset the color adjustments “Color Reset”
This function only resets the color adjustments for the currently selected...

33Chapter4PowerSavingFunctions
Chapter 4 Power Saving Functions
4-1. Setting Power Saving “Power Save”
 ●Monitor
This function allows you to specify whether to set the monitor into the power saving mode, depending on the 
state of an external device connected to it. When the monitor has shifted to the power saving mode, the 
images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
•
 
P
 ower...

34Chapter4PowerSavingFunctions
Attention
• When all the conditions below are met, the monitor does not change to the power saving mode even if “Power Save” is set to “Enable”:
-
 
“
 Power Save” for Sound is set to “Sound On” ( “Audio Output” (page 34))
-
 
I
 n the mute state ( “To mute the sound temporarily” (page 29) )
In these cases, reset the mute.
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display 
mode....

35Chapter4PowerSavingFunctions
4-3. Enabling/Disabling Automatic Brightness Adjustment “Auto EcoView”
The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness 
automatically and comfortably by using the Auto EcoView function.
Attention
• Be careful not to block the sensor on the lower side of the monitor when using the Auto EcoView function.
Procedure
1.
 
P
 ress 
 on the remote control.
The “EcoView Menu” appears.
2. Select “On” or “Off ” with...

36Chapter4PowerSavingFunctions
Cancelling procedure
1. 
P
 ress 
 until “Disable” appears.
Checking the remaining time
1.
 
P

ress 
 when the Off Timer is set.
The time to turn off the power appears.
Time extension procedure
1.  
P
 ress 
 while the remaining time is displayed.
Each time you press , the time is extended.
  

37Chapter5ConnectingCables
Chapter 5 Connecting Cables
5-1. Connecting Multiple External Devices
The product has multiple connections to external devices and allows you to switch to one of the connections for 
display.
Attention
• Do not use dual link cables.
Connection examples
DVI-HDMIconvertercable
( Commercially  available  product) D-Sub
 mini
15 -pin  connector
DVI  connector
Signal  cable
(supplied  FD-C39)
Signal  cable
(MD-C87  option)
HDMI  cable
(Commercially  available ...

38Chapter6Troubleshooting
Chapter 6 T roubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
No picture
Problem Possible cause and remedy
1. No picture
• 
P
 ower  indicator  does  not  light.•
C heck  whether  the  power  cord  is  connected  properly.
• 
T
 urn  the  main  power  switch  on.
•

T
 urn  off  the  main  power,  and  then  turn  it  on  again  a 
f

ew  minutes  later.
•

P
 ower  indicator  is ...

39Chapter6Troubleshooting
Imaging problems (for both digital and analog)
Problem Possible cause and remedy
3. The screen is too bright or too dark. • U se  “Brightness”  or  “Contrast”  in  the  Setting  menu  to 
a

djust  it.  (The  LCD  monitor  backlight  has  a  limited  life 
s

pan.  When  the  screen  becomes  dark  or  begins  to 
fl

icker,  contact  your  local  dealer.)
•

T
 urn  on  the  Auto  EcoView  function.  The  monitor 
d

etects  the ...

40Chapter6Troubleshooting
Imaging problems (for analog only)
Problem Possible cause and remedy
12. Display position is incorrect.•Use “Position”  in  the  Setting  menu  to  correct  the 
i

mage  position  (see  “To  correct  the  screen  position 
“

Position””  (page  26)).
•

I
 f  the  problem  persists,  use  the  graphics  board’s  utility 
i

f  available  to  change  the  display  position.
13.
 
V

ertical bars appear on the screen or a 
part of the image...