Eizo Flexscan S2431w Users Manual

							
39Chapter 5  Reference

sRGB (Standard RGB)
International standard for “color reproduction and color space” among peripheral devices (such as monitors, printers, 
digital cameras, scanners). sRGB allows Internet users to closely match colors as a simple color matching means for 
the Internet use.
Temperature Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin.  The screen 
becomes reddish at a low temperature, and bluish at a high temperature, like the fl ame temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling) A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling) VESA provides the standardization of signals from PC (graphics board) for power saving of PC monitors. DPMS 
defines the signal status between PC and monitor.
 
						

							
40Chapter 5  Reference

5-5  Preset Timing
The following table shows factory preset video timing (for analog signal only).
ModeDot clock
Frequency
PolarityHorizontal: kHz
Vertical: Hz
VGA 640×480@60Hz
25.2 MHzHorizontal31.47Negative
Vertical
59.94Negative
VGA 720×400@70Hz
28.3 MHzHorizontal31.47Negative
Vertical
70.09Positive
Macintosh 640×[email protected] MHzHorizontal35.00Negative
Vertical
66.67Negative
Macintosh 832×[email protected] MHzHorizontal49.72Negative
Vertical
74.55Negative
Macintosh 1152×
[email protected] MHzHorizontal68.68Negative
Vertical
75.06Negative
Macintosh 1280×[email protected] MHzHorizontal74.76Positive
Vertical
74.76Positive
VESA 640×480@72Hz
31.5 MHzHorizontal37.86Negative
Vertical
72.81Negative
VESA 640×480@75Hz
31.5 MHzHorizontal37.50Negative
Vertical
75.00Negative
VESA 640×480@85Hz
36.0 MHzHorizontal43.27Negative
Vertical
85.01Negative
VESA 800×600@56Hz
36.0 MHzHorizontal35.16Positive
Vertical
56.25Positive
VESA 800×600@60Hz
40.0 MHzHorizontal37.88Positive
Vertical
60.32Positive
VESA 800×600@72Hz
50.0 MHzHorizontal48.08Positive
Vertical
72.19Positive
VESA 800×600@75Hz
49.5 MHzHorizontal46.88Positive
Vertical
75.00Positive
VESA 800×600@85Hz
56.3 MHzHorizontal53.67Positive
Vertical
85.06Positive
VESA 1024×768@60Hz
65.0 MHzHorizontal48.36Negative
Vertical
60.00Negative
VESA 1024×768@70Hz
75.0 MHzHorizontal56.48Negative
Vertical
70.07Negative
VESA 1024×768@75Hz
78.8 MHzHorizontal60.02Positive
Vertical
75.03Positive
VESA 1024×768@85Hz
94.5 MHzHorizontal68.68Positive
Vertical
85.00Positive
VESA 1152×864@75Hz
108.0 MHzHorizontal67.50Positive
Vertical
75.00Positive
VESA 1280×960@60Hz
108.0 MHzHorizontal60.00Positive
Vertical
60.00Positive
VESA 1280×1024@60Hz
108.0 MHzHorizontal63.98Positive
Vertical
60.02Positive
VESA 1280×1024@75Hz
135.0 MHzHorizontal79.98Positive
Vertical
75.03Positive
VESA 1280×1024@85Hz 
(S2431W)157.5 MHzHorizontal91.15Positive
Vertical
85.03Positive
VESA 1600×1200@60Hz 
(S2431W)162.0 MHzHorizontal75.00Positive
Vertical
60.00Positive
VESA 1600×1200@65Hz 
(S2431W)175.0 MHzHorizontal81.30Positive
Vertical
65.00Positive
VESA 1600×1200@70Hz 
(S2431W)189.0 MHzHorizontal87.50Positive
Vertical
70.00Positive
VESA 1600×1200@75Hz 
(S2431W)202.5 MHzHorizontal93.80Positive
Vertical
75.00Positive
Attention
•  Display position may be deviated 
depending on the PC connected, 
which may require screen adjustment 
using Adjustment menu.
•  If a signal other than those listed in 
the table is input, adjust the screen 
using the Adjustment menu. However, 
screen display may still be incorrect 
even after the adjustment.
•  When interlace signals are used, the 
screen cannot be displayed correctly 
even after screen adjustment using the 
Adjustment menu.
 
						

							
41Chapter 5  Reference

ModeDot clock
Frequency
PolarityHorizontal: kHz
Vertical: Hz
VESA CVT 
 1680×[email protected] MHzHorizontal65.29Negative
Vertical
59.95Positive
VESA CVT RB 
 1680×1050@60Hz 119.0 MHz
Horizontal64.67Positive
Vertical
59.88Negative
VESA CVT (S2431W) 
1920×[email protected] MHzHorizontal74.56Negative
Vertical
59.89Positive
VESA CVT RB (S2431W) 
1920×[email protected] MHzHorizontal74.04Positive
Vertical
59.95Negative
 
						

							
42Chapter 5  Reference

Congratulations!
The display you have just purchased carries the TCO’03 Displays label. This 
means that your display is designed, manufactured and tested according to 
some of the strictest quality and environmental requirements in the world. 
This makes for a high performance product, designed with the user in focus 
that also minimizes the Impact on our natural environment.
Some of the features of the TCO’03 Display requirements: Ergonomics
●  Good visual ergonomics and image quality in order to improve the working environment for the user 
and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, 
reflectance, colour rendition and image stability.
Energy
●   Energy-saving mode after a certain time - beneficial both for the user and environment
●  Electrical safety
Emissions
●  Electromagnetic fields
●  Noise emissions
Ecology
●  The products must be prepared for recycling and the manufacturer must have a certified environmental 
management system such as EMAS or ISO 14000
●  Restrictions on
●  chlorinated and brominated flame retardants and polymers
●  heavy metals such as cadmium, mercury and lead.
The requirements includes in this label have been developed by TCO Development in co-operation with scientists, 
experts, users as well as manufacturers all over the world. Since the end of the 1980s  TCO has been involved in 
influencing the development of IT equipment in a more user-friendly direction. Our labeling system with displays 
in 1992 and is now requested by users and IT-manufacturers all over the world.
For more information, please visit www.tcodevelopment.com
 
						

							
43

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible PartyEIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone:  (562) 431-5011
declare that the product Trade name:  EIZO
Model:  FlexScan S2031W/S2431W
is in conformity with Part 15 of the FCC Rules. Operation of this pr oduct is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a 
residential installation.  This equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications.  However , 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment of f and on, the user 
is encouraged to try to correct the interference by one or more of the following measures.
*  Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user ’s 
authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the 
limits of a Class B digital device.
-  AC Cord
-  Shielded Signal Cable (enclosed)
-  Stereo mini-jack Cable
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
 
						

							
44
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät  und  des  spezifizierten  Zubehörs  besitzen.  Das  Gewicht  des  Bildschirmgerätes  und  des  Zubehörs  sind  in  der 
zugehörenden Bedienungsanleitung angegeben.
b) Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher  als die Augenhöhe eines Benutzers in sitzender Position ist.
c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der 
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d) Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach 
hinten ≥ 5°).
e) Der  Standfuß  muß  die  Möglichkeit  zur  Drehung  des  Bildschirmgerätes  besitzen  (max.  ±180°).  Der  maximale 
Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g) Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h) Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position 
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1680 × 
1050 (S2031W)/1920 × 1200 (S2431W), Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non 
interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem 
Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.
Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.
Kopfhörerausgang und damit auch den Schalldruckpegel.
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
[Begrenzung des maximalen Schalldruckpegels am Ohr]
Bildschirmgeräten: Größte Ausgangsspannung 150 mV