Eizo Flexscan S2201w Users Manual

							
29Chapter 4  Troubleshooting

ProblemsPossible cause and remedy
18.  The monitor connected with the USB cable is 
detected. / USB devices connected to the monitor 
does not work. •  Check whether the USB cable is connected correctly.
•  Change the USB port to another one. If the PC or peripheral devices works correctly by changing the USB 
port, contact your local dealer. (Refer to the manual of 
the PC for details.)
•  Please perform the followings to check the status.
 
•  Reboot the PC.
 
•  Connect the PC and peripheral devices directly.
•  If the PC or peripheral devices works correctly without  connecting each other via the monitor (working as a USB 
hub), please contact your local dealer. 
•  Check whether the PC and OS are USB compliant. (For 
USB compliance of the respective devices, consult their 
manufacturers.)
•  Check the PC’s BIOS setting for USB when using 
Windows. (Refer to the manual of the PC for details.)
 
						

							
30Chapter 5  Reference

Chapter 5  Reference
5-1  Attaching an Arm
The stand can be removed and replaced with an arm (or another stand) to be 
attached to the monitor. Use an arm or stand of EIZO option.
[Attaching]
1  Lay the LCD monitor on a soft cloth spread over on a stable 
surface with the panel surface facing down.
2  Remove the stand. (Prepare a screwdriver.)
Unscrew the four screws securing the unit and the stand with the 
screwdriver.
3  Attach the monitor to the arm or stand.Secure the monitor to the arm or stand using the screws specified in the 
user’s manual of the arm or stand.
Attention
•  When attaching an arm or stand, follow the instructions of their user’s 
manual.
•  When using another manufacturer’ s arm or stand, confirm the following 
in advance and select one conforming 
to the VESA standard. Use the M4 
× 12 mm screws supplied with this 
monitor.
– Clearance between the screw holes: 
100 mm × 100 mm
– Thickness of plate: 2.6 mm
– Strong enough to support weight of 
the monitor unit (except the stand) 
and attachments such as cables.
•  When using an arm or stand, attach it  to meet the following tilt angles of the 
monitor.
– Height adjustable stand:
 
Up 40 degrees, down 0 degrees 
(vertical display, 90 degrees 
clockwise)
– EZ-UP stand:
 
Up 25 degrees, down 0 degrees 
(vertical display, 90 degrees 
clockwise)
•  Connect the cables after attaching an 
arm.
•  If you need to remove the EZ-UP 
stand, turn the panel on the monitor 
to the left and right a little to appear 
the four screws positioned under the 
stand. Then unscrew the four screws. 
 
						

							
31Chapter 5  Reference

Attention
•  Never use any solvents or chemicals, such as thinner, benzene, wax, 
alcohol, and abrasive cleaner, which 
may damage the cabinet or LCD 
panel.
NOTE
•  Optional ScreenCleaner is 
recommended for cleaning the LCD 
panel surface.
5-2  Cleaning
Clean the monitor periodically to keep the monitor clean and extend its life.
Cabinet
Clean the cabinet with a soft cloth dampened with little mild deter gent.
LCD Panel
•  Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning 
paper. 
•  Remove persistent stains gently with a cloth dampened with little water, and  then clean the LCD panel again with a dry cloth for better finishing.
 
						

							
32Chapter 5  Reference

5-3  Specifications
S2001W
LCD Panel20.1-inch (510 mm) TFT color LCD with anti-glare hard coating
Viewing angle*
: Horizontal 170°, Vertical 170°  (CR:10 or more)
Dot Pitch0.258mm
Horizontal Scan FrequencyAnalog: 24-82kHzDigital: 31-65kHz
Vertical Scan Frequency
Analog: 49-86Hz (Non-interlace) (1280 × 1024: 49-76Hz)(1680 × 1050: 49-61Hz)Digital: 59-61Hz (Non-interlace)
(VGA TEXT: 69-71Hz)
Resolution1680 dots × 1050 lines
Max. Dot ClockAnalog: 150MHzDigital: 120MHz
Max. Display Color Approx. 16.77 million colors: Applicable to 8 bit (1048.77 million colors)
Display Area (H × V)
433.4mm × 270.9mm
Power Supply 100-120 VAC ±10%, 50/60Hz 1.0A
200-240 VAC ±10%, 50/60Hz 0.6A
Power ConsumptionScreen Display On60W or less (with USB load, when stereo mini jack is connected)50W or less (without USB load, when stereo mini jack is not connected)
Power saving mode1W or less (for single signal input, without USB load, when stereo mini jack is not connected)
Power button Off
0.7W or less (without USB load, when stereo mini jack is not connected)
Input Signal ConnectorDVI-I connector (Applicable to HDCP), D-Sub mini 15-pin
Analog Input Signal (Sync) Separate, TTL, positive/ negative
Composite, TTL, positive/ negative
Analog Input Signal (Video)
Analog, Positive (0.7Vp-p/75Ω)
Digital Signal Transmission System
TMDS (Single Link)
Video Signal Memory
Analog signal: 45 (preset: 24)
Digital signal: 10 (preset: 0)
Audio Output Speaker output: 0.5W + 0.5W (8Ω, THD: 10% or less)Headphone output: 2mW + 2mW
Line inputInput impedance : 47 kΩ (typ.)
Input level :1.0 Vrms (Max.)
Plug & PlayVESA DDC 2B / EDID structure 1.3
Dimensions (Width) × (Height) × (Depth) mm (inch)
Main unit (including Height adjustable stand)
469mm(18.5) × 427 - 509mm(16.8 - 20.0) × 208.5mm(8.2)
Main unit (including 
EZ-UP stand)469mm(18.5) × 339.5 - 504.5mm(13.4 - 19.9) × 279.9 - 291.9mm(11.0 - 
11.5)
Main unit (without stand)469mm(18.5) × 309mm(12.2) × 69.5mm(2.7)
Mass Main unit (including Height adjustable stand)
8.7 kg (19.2 lbs.)
Main unit (including 
EZ-UP stand)10.5 kg (23.1 lbs.)
Main unit (without stand)5.7 kg (12.6 lbs.)
* LCD Module characteristics only