Eizo Flexscan S1921 Users Manual

19Chapter 3  Connecting Cables

3-1 Connecting Two PCs to the Monitor
Two	PCs	can	be	connected	to	the	monitor	through	the	DVI-D	and	the	D-Sub	
mini 15 pin connector on the back of the monitor.
Connection examples
Chapter 3  Connecting Cables
Selecting input signal
Input Signal Selection button
Switch	the	input	signal	with	. Input signal switches each time  is pressed. 
When	the	signal	is	switched,	the	active	signal	type	(Analog	or	Digital)	appears	
at the top right corner of the screen for two seconds....

20Chapter 4  Troubleshooting

Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer .
•  No-picture problems → See No.1 - No.2.
•  Imaging problems → See No.3 - No.11.
•  Other problems → See No.12.
ProblemsPossible cause and remedy
1.	No picture
•  Power indicator does not light. • 
Check whether the power cord is connected correctly. If 
the problem persists, turn off the monitor, and then turn it 
on again a few minutes later.
•  Power...

21Chapter 4  Troubleshooting
ProblemsPossible cause and remedy
8.  Green/red/blue/white dots or defective dots remain 
on the screen. • 
This is due to LCD panel characteristics and is not a failure.
9.  Interference patterns or fingerprints remain on the 
screen. • 
Leave the monitor with a white screen. The symptom may disappear.
10.  The Main menu of Adjustment menu does not start. • Check for Adjustment Lock function.
11.  The auto-adjustment function does not work 
correctly. • 
This function does...

22Chapter 5  Reference 

5-1 Attaching an Arm (Option)
The	stand	can	be	removed	and	replaced	with	an	arm	(or	another	stand)	to	be	
attached to the monitor. Use an arm or stand of EIZO option.
[Attaching]
1 Lay the LCD monitor on a soft cloth spread over on a stable 
surface with the panel surface facing down.
2 Remove the stand. (Prepare a screwdriver.)
Unscrew	the	four	screws	securing	the	unit	and	the	stand	with	the	
screwdriver.
3  Attach the monitor to the arm or stand.
Secure the monitor to the arm...

23Chapter 5  Reference 

5-2 Power Saving Mode
 Analog input
This monitor complies with the VESA DPMS standard.
[Power Saving System]
PCMonitorPower
Indicator
OperatingOperatingBlue
PowersavingSTAND-BYSUSPENDED OFFPower savingOrange
[Resumption Procedure]
(1) Operate the mouse or keyboard to resume the normal screen.
 Digital input
This monitor complies with the DVI DMPM standard.
[Power Saving System]
The monitor enters the power saving mode in fi ve seconds in connection with
the PC setting....

24Chapter 5  Reference 
5-4 Glossary
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in 
use, when the analog input signal is converted to a digital signal for image display . 
This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’ s digital data without loss.
This...

25Chapter 5  Reference 

5-5 Preset Timing
The following table shows factory preset video timing.
ModeDot clock
Frequency
PolarityHorizontal: kHz
Vertical: Hz
VGA 640×[email protected] MHzHorizontal31.47Negative
Vertical59.94Negative
VGA 720×[email protected] MHzHorizontal31.47Negative
Vertical70.09Positive
Macintosh 640×[email protected] MHzHorizontal35Negative
Vertical66.67Negative
Macintosh 832×[email protected] MHzHorizontal49.73Negative
Vertical74.55Negative
Macintosh 1152×[email protected] MHzHorizontal68.68Negative...

2Chapter 5  Reference 

Congratulations!
The display you have just purchased carries the TCO’03 Displays label. This 
means that your display is designed, manufactured and tested according t\
o 
some of the strictest quality and environmental requirements in the world. 
This makes for a high performance product, designed with the user in foc\
us 
that also minimizes the Impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
● Good visual ergonomics...

27 

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible PartyEIZO NANAO TECHNOLOGIES INC.
5710	Warland	Drive,	Cypress,	CA 	90630
Phone:		(562)	431-5011
declare that the product Trade	name:		EIZO
Model:		FlexScan	S1701,	S1721,	S1731,	S1901,	S1911,	
S1921,	S1931
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must...

28 

Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:Der	Standfuß	muß	den	nachfolgenden	 Anforderungen	entsprechen:
a)  Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes...