Eizo Flexscan S1902sh Users Manual

							21Chapter 3  Connecting Cables
Chapter	3	 Connecting	Cables
3-1	Connecting	Multiple	PCs	to	the	Monitor	
Multiple PCs can be connected to the DVI-D, D-Sub mini 15 pin connector on 
the back of the monitor to switch the display.
Connection	examples
DVI-D connectorD-sub mini 
 
15-pin Connector
To PC 1 To PC 2
DVI connector
Signal cable (Digital) 
FD-C39 (supplied) D-sub mini 15-pin 
Connector
Signal cable (Analog)   
MD-C87 (supplied)
●	 To	switch	the	input	signal
Input Signal Selection button
Switch the input signal with . Input signal switches each time  is pressed. 
When the signal is switched, the active signal type (Analog or Digital) appears 
at the top right corner of the screen for three seconds.
●	 To	set	input	signal	selection	[Input	Signal]
Setting Function
Auto When a PC is turned off or enters the powersaving 
mode, the monitor automatically displays another signal.
Manual The monitor detects only the PC’s signals currently 
displaying automatically. Select an active input signal 
with 
.
[Procedure]
(1) Choose  from the Adjustment menu, and press 
.
(2)  Choose  from the  menu, and press 
.
The  menu appears.
(3) Select “Auto” or “Manual” with  or , and press .
The setting is completed.
NOTE
• When “Auto” is selected for , the monitor’s power-saving 
function works only when the two 
PCs are in the power-saving mode.
   
						

							22Chapter 4  Troubleshooting
Chapter	4	 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
•  No-picture problems → See No.1 - No.2.
•  Imaging problems (digital input) → See No.6 - No.11.
•  Imaging problems (analog input) → See No.3 - No.11.
•  Other problems → See No.12 - No.14.
Problems Possible	cause	and	remedy
1.  
No	picture
•  Power indicator does not light. • 
Check whether the power cord is connected correctly. If 
the problem persists, turn off the monitor, and then turn it 
on again a few minutes later.
•  Press 
.
•  Power indicator is lighting blue. • Set each adjusting value in ,  
and  to higher level. ( page 17)
•  Power indicator is lighting orange. • Switch the input signal with 
.
•  Operate the mouse or keyboard.
•  Turn on the PC. 
2.	 The	message	below	appears. This message appears when the signal is not input 
correctly even when the monitor functions properly.
•  This message appears when no signal is input.
  Example:
• The message shown left may appear, because some 
PCs do not output the signal soon after power-on.
•  Check whether the PC is turned on.
•  Check whether the signal cable is connected properly. 
•  Switch the input signal with 
.
•  When inputting a sync-on-green signal, the [SoG] setting 
for the monitor must be changed in advance (for analog 
signal). (page 10 )
•  The message below shows that the input signal is 
out of the specified frequency range. (Such signal 
frequency is displayed in red.)
  Example:
• Check whether the signal setting of your PC matches 
the resolution and the vertical frequency settings for the 
monitor. (page 10 )
•  Reboot the PC.
•  Select an appropriate display mode using the graphics 
board’s utility software. Refer to the manual of the 
graphics board for details.
 fD  : Dot Clock
(Displayed only when the digital signal inputs)
  fH  : Horizontal Frequency
  fV  : Vertical Frequency
3.	 	Display	position	is	incorrect.
• Adjust image position so that it is displayed properly 
within the display area using the  and 
 adjustment.
•  If the problem persists, use the graphics board’s utility 
software if available to change the display position.
4.	 Vertical	bars	appear	on	the	screen	or	a	part	of	the	 image	is	flickering.
• Adjust using .  (page 14)
5.	 Whole	screen	is	flickering	or	blurring.
•  Adjust using .  (page 14)
   
						

							23Chapter 4  Troubleshooting
ProblemsPossible	cause	and	remedy
6.	 Characters	are	blurred. • Check whether the signal setting of your PC matches 
the resolution and the vertical frequency settings for the 
monitor. (page 10 )
•  Adjust using . ( page 15)
7.	 The	screen	is	too	bright	or	too	dark. • Adjust using  or . (The LCD 
monitor backlight has a fixed life span. When the screen 
becomes dark or begins to flicker, contact your local 
dealer.)
•  Turn on the Auto EcoView function. ( page 19) The monitor 
detects the environmental brightness to adjust the 
screen brightness automatically.
8.	 Afterimages	appear. • Afterimages are particular to LCD monitors. Avoid 
displaying the same image for a long time.
•  Use the screen saver or power save function to avoid 
displaying the same image for extended periods of time.
9.	 Green/red/blue/white	dots	or	defective	dots	remain	 on	the	screen. • 
This is due to LCD panel characteristics and is not a 
failure.
10.	 Interference	patterns	or	pressure	marks	remain	on	 the	screen. • 
Leave the monitor with a white or black screen. The 
symptom may disappear.
11.	 The	display	image	is	appeared	in	lengthwise. • Check whether the kind of cables connected with the 
monitor and the PC. (Re-connect the monitor and cables 
correctly by referring to the Setup Guide.)
12.	 The	adjustment	menu	does	not	appear. • Check whether the operation lock function works. ( page 19)
13.	 The	auto-adjustment	function	does	not	work	 correctly. • 
This function does not work when digital signal is input.
•  This function works correctly when an image is fully 
displayed over the display area.  
It does not work properly when an image is displayed 
only on a part of the screen (DOS prompt window, for 
example) or when a black background (wallpaper, etc.) is 
in use. 
This function does not work correctly with some graphics 
boards.
14.	 No	audio	output • Check whether the mini jack cable is correctly.
•  Check whether volume is set to “0”.
•  Check the settings of the PC and the audio playback 
software.
  
						

							24Chapter 5  Reference
Chapter	5	 Reference
5-1	How	to	Attach	the	Optional	 Arm
An optional arm (or an optional stand) can be attached by removing the stand 
section.  Please refer to our web site for the corresponding optional arm (or 
optional stand).
http://www.eizo.com
[Attaching]
1	 Lay	the	LCD	monitor	on	a	soft	cloth	spread	over	on	a	stable	
surface	with	the	panel	surface	facing	down.
2	 Remove	the	stand.	(Prepare	a	screwdriver.)Unscrew the four screws securing the unit and the stand with the 
screwdriver.
3	 Attach	the	monitor	to	the	arm	or	stand.Secure the monitor to the arm or stand using the screws specified in the 
user’s manual of the arm or stand.
Attention
• When attaching an arm or stand, 
follow the instructions of their user’s 
manual.
•  When using another manufacturer’s 
arm or stand, confirm the following in 
advance and select one conforming to 
the VESA standard. Use M4 × 12 mm 
screws supplied with the monitor.
– Clearance between the screw holes:   
100 mm × 100 mm
–  Thickness of plate: 2.6 mm
–  Strong enough to support weight of 
the monitor unit (except the stand) 
and attachments such as cables.
•  When using an arm or stand, attach it 
to meet the following tilt angles of the 
monitor.
– Up 60 degrees, down 45 degrees 
(horizontal display)
– Up 45 degrees, down 45 degrees  (vertical display, 90 degrees 
clockwise)
•  Connect the cables after attaching an 
arm or a stand.
•  If you need to remove the EZ-UP 
stand, turn the panel on the monitor 
to the left and right a little to appear 
the four screws positioned under the 
stand. Then unscrew the four screws.
   
						

							25Chapter 5  Reference
5-2	Power	Saving	Mode
	 Analog	input
This monitor complies with the VESA DPMS standard.
[Power	Saving	System]
PC MonitorPower
Indicator
Operating OperatingBlue
Power saving STAND-BY
SUSPENDED 
OFF Power saving
Orange
	 Digital	input
This monitor complies with the DVI DMPM standard.
[Power	Saving	System]
The monitor enters the power saving mode in five seconds in connection with
the PC setting.
PC MonitorPower	Indicator
Operating Operating Blue
Power saving Power saving Orange
Attention
• Unplugging the power cord 
completely shuts off power supply to 
the monitor.
•  Power consumption varies even 
when the stereo mini jack cable is 
connected.
   
						

							26Chapter 5  Reference
5-3	Specifications
S1701-X
LCD Panel17-inch (43 cm) TFT color LCD with hard coating
Viewing angle: Horizontal 160°, Vertical 160° (CR: 10 or more)
Dot Pitch 0.264 mm 
Horizontal Scan Frequency Analog: 31 - 80 kHz
Digital: 31 - 64 kHz
Vertical Scan Frequency Analog: 50 - 75 Hz (Non-interlace)
Digital: 59 - 61 Hz (VGA Text: 69 - 71 Hz) (Non-interlace)
Resolution 1280 dots × 1024 lines
Max. Dot Clock Analog: 135 MHz
Digital: 108 MHz
Max. Display Colors Approx. 16.77 million colors (1064.33 million colors/10bit LUT)
Display Area (H × V)  337.9 mm × 270.3 mm
Power Supply 100 - 120 VAC ±10% 50/60 Hz, 0.65 A
200 - 240 VAC ±10% 50/60 Hz, 0.4 A
Power 
Consumption Screen Display On
38W or less (Speaker working)
35W or less (Speaker not working)
Power saving mode 0.6W or less (0.5W typ.)
(for single signal input, when stereo mini jack cable is not connected, [Input 
Signal] : “Auto”, [SoG] : “Off”)
Power button Off 0.5W or less (when stereo mini jack cable is not connected)
Input Signal Connectors DVI-D connector, D-sub mini 15-pin connector
Analog Input Signal (Sync) Separate, TTL, Positive/Negative
Sync on Green, 0.3Vp-p, Negative
Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω)
Digital Signal Transmission System  TMDS (Single Link)
Video Signal Memory Analog Signal: 26
Audio output Speaker output: 0.5 W + 0.5 W (8 Ω, THD+N: 10% or less)
Headphone output: 2mW + 2mW (32 Ω, THD+N: 3% or less)
Line input Input impedance 47 kΩ (typ.)
Input level: 1.0 Vrms (Max.)
Plug & Play  VESA DDC 2B/EDID structure 1.3
Dimensions
(Width) ×
(Height) ×
(Depth) Main unit  
(including Tilt Stand)
363 mm (14.3 inch) × 382 mm (15 inch) × 188 mm (7.4 inch)
Main unit  
(including Height 
adjustable Stand) 363 mm (14.3 inch) × 389.5 - 489.5 mm (15.3 - 19.3 inch) × 205 mm (8.1 inch)
Main unit  
(without stand) 363mm (14.3 inch) × 300 mm (11.8 inch) × 59 mm (2.32 inch)
Mass Main unit  
(including Tilt Stand) Approx. 4.7 kg (10.4 lbs)
Main unit  
(including Height 
adjustable Stand) Approx. 5.9 kg (13 lbs)
Main unit  
(without stand) Approx. 3.9 kg (8.6 lbs)
Movable range Tilt Stand Tilt: 30° Up, 5° Down
Height adjustable 
Stand Tilt: 30° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 100 mm (3.9 inch)
Rotation: 90° (clockwise)
  
						

							27Chapter 5  Reference
Environmental 
ConditionsTemperature
Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Storage temperature: –20 °C - 60 °C (-4 °F - 140 °F)
Humidity Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa
S1721-X
LCD Panel 17-inch (43 cm) TFT color LCD with hard coating
Viewing angle: Horizontal 178°, Vertical 178° (CR: 10 or more)
Dot Pitch 0.264 mm 
Horizontal Scan Frequency Analog: 31 - 80 kHz
Digital: 31 - 64 kHz
Vertical Scan Frequency Analog: 50 - 75 Hz (Non-interlace)
Digital: 59 - 61 Hz (VGA Text: 69 - 71 Hz) (Non-interlace)
Resolution 1280 dots × 1024 lines
Max. Dot Clock Analog: 135 MHz
Digital: 108 MHz
Max. Display Colors Approx. 16.77 million colors (1064.33 million colors/10bit LUT)
Display Area (H × V)  337.9 mm × 270.3 mm
Power Supply 100 - 120 VAC ±10% 50/60 Hz, 0.65 A
200 - 240 VAC ±10% 50/60 Hz, 0.4 A
Power 
Consumption Screen Display On
38W or less (Speaker working)
35W or less (Speaker not working)
Power saving mode 0.6W or less (0.5W typ.)
(for single signal input, when stereo mini jack cable is not connected, [Input 
Signal] : “Auto”, [SoG] : “Off”)
Power button Off 0.5W or less (when stereo mini jack cable is not connected)
Input Signal Connectors DVI-D connector, D-sub mini 15-pin connector
Analog Input Signal (Sync) Separate, TTL, Positive/Negative
Sync on Green, 0.3Vp-p, Negative
Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω)
Digital Signal Transmission System  TMDS (Single Link)
Video Signal Memory Analog Signal: 26
Audio output Speaker output: 0.5 W + 0.5 W (8 Ω, THD+N: 10% or less)
Headphone output: 2mW + 2mW (32 Ω, THD+N: 3% or less)
Line input Input impedance 47 kΩ (typ.)
Input level: 1.0 Vrms (Max.)
Plug & Play  VESA DDC 2B/EDID structure 1.3
Dimensions
(Width) ×
(Height) ×
(Depth) Main unit 
(including Height 
adjustable Stand)
363 mm (14.3 inch) × 389.5 - 489.5 mm (15.3 - 19.3 inch) × 205 mm (8.1 inch)
Main unit  
(without stand) 363mm (14.3 inch) × 300 mm (11.8 inch) × 59 mm (2.32 inch)
Mass Main unit
(including Height 
adjustable Stand) Approx. 5.9 kg (13 lbs)
Main unit  
(without stand) Approx. 3.9 kg (8.6 lbs)
Movable range Height adjustable 
Stand Tilt: 30° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 100 mm (3.9 inch)
Rotation: 90° (clockwise)
  
						

							28Chapter 5  Reference
Environmental 
ConditionsTemperature
Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Storage temperature: –20 °C - 60 °C (-4 °F - 140 °F)
Humidity Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa
S1902
LCD Panel 19-inch (48 cm) TFT color LCD with anti-glare hard coating
Viewing angle: Horizontal 170°, Vertical 160° (CR: 10 or more)
Dot Pitch 0.294 mm 
Horizontal Scan Frequency Analog: 31 - 80 kHz
Digital: 31 - 64 kHz
Vertical Scan Frequency Analog: 50 - 75 Hz (Non-interlace)
Digital: 59 - 61 Hz (VGA Text: 69 - 71 Hz) (Non-interlace)
Resolution 1280 dots × 1024 lines
Max. Dot Clock Analog: 135 MHz
Digital: 108 MHz
Max. Display Colors Approx. 16.77 million colors (1064.33 million colors/10bit LUT)
Display Area (H × V)  376.3 mm × 301.0 mm
Power Supply 100 - 120 VAC ±10% 50/60 Hz, 0.55 A
200 - 240 VAC ±10% 50/60 Hz, 0.35 A
Power 
Consumption Screen Display On
30W or less (Speaker working)
27W or less (Speaker not working)
Power saving mode 0.6W or less (0.5W typ.)
(for single signal input, when stereo mini jack cable is not connected, [Input 
Signal] : “Auto”, [SoG] : “Off”)
Power button Off 0.5W or less (when stereo mini jack cable is not connected)
Input Signal Connectors DVI-D connector, D-sub mini 15-pin connector
Analog Input Signal (Sync) Separate, TTL, Positive/Negative
Sync on Green, 0.3Vp-p, Negative
Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω)
Digital Signal Transmission System  TMDS (Single Link)
Video Signal Memory Analog Signal: 26
Audio output Speaker output: 0.5 W + 0.5 W (8 Ω, THD+N: 10% or less)
Headphone output: 2mW + 2mW (32 Ω, THD+N: 3% or less)
Line input Input impedance 47 kΩ (typ.)
Input level: 1.0 Vrms (Max.)
Plug & Play  VESA DDC 2B/EDID structure 1.3
Dimensions
(Width) ×
(Height) ×
(Depth) Main unit  
(including Tilt Stand)
405 mm (15.9 inch) × 416 mm (16.4 inch) × 205 mm (8.1 inch)
Main unit 
(including Height 
adjustable Stand) 405 mm (15.9 inch) × 406.5 - 506.5 mm (16 - 19.9 inch) × 205 mm (8.1 inch)
Main unit  
(including EZ-UP 
stand) 405 mm (15.9 inch) × 347.7 - 507 mm (13.7 - 20 inch) × 246.8 - 277.6 mm (9.7 
- 10.9 inch)
Main unit  
(without stand) 405 mm (15.9 inch) × 334 mm (13.1 inch) × 61.5 mm (2.42 inch)
  
						

							29Chapter 5  Reference
MassMain unit  
(including Tilt Stand) Approx. 6.0 kg (13.2 lbs)
Main unit  
(including Height 
adjustable Stand) Approx. 7.2 kg (15.9 lbs)
Main unit  
(including EZ-UP 
stand) Approx. 8.8 kg (19.4 lbs)
Main unit  
(without stand) Approx. 5.2 kg (11.5 lbs)
Movable range Tilt Stand Tilt: 30° Up, 5° Down
Height adjustable 
Stand Tilt: 30° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 100 mm (3.9 inch)
Rotation: 90° (clockwise)
EZ-UP stand Tilt: 25° Up, 0° Down
Swivel: 172° Right, 172° Left
Adjustable height: 154 mm (6.1 inch) (Tilt : 0°)
Rotation: -10° - 92° (clockwise)
Environmental 
Conditions Temperature
Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Storage temperature: –20 °C - 60 °C (-4 °F - 140 °F)
Humidity Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa
S1921-X
LCD Panel 19-inch (48 cm) TFT color LCD with hard coating
Viewing angle: Horizontal 178°, Vertical 178° (CR: 10 or more)
Dot Pitch 0.294 mm 
Horizontal Scan Frequency Analog: 31 - 80 kHz
Digital: 31 - 64 kHz
Vertical Scan Frequency Analog: 50 - 75 Hz (Non-interlace)
Digital: 59 - 61 Hz (VGA Text: 69 - 71 Hz) (Non-interlace)
Resolution 1280 dots × 1024 lines
Max. Dot Clock Analog: 135 MHz
Digital: 108 MHz
Max. Display Colors Approx. 16.77 million colors (1064.33 million colors/10bit LUT)
Display Area (H × V)  376.3 mm × 301.0 mm
Power Supply 100 - 120 VAC ±10% 50/60 Hz, 0.7 A
200 - 240 VAC ±10% 50/60 Hz, 0.4 A
Power 
Consumption Screen Display On
40W or less (Speaker working)
37W or less (Speaker not working)
Power saving mode 0.6W or less (0.5W typ.)
(for single signal input, when stereo mini jack cable is not connected, [Input 
Signal] : “Auto”, [SoG] : “Off”)
Power button Off 0.5W or less (when stereo mini jack cable is not connected)
Input Signal Connectors DVI-D connector, D-sub mini 15-pin connector
Analog Input Signal (Sync) Separate, TTL, Positive/Negative
Sync on Green, 0.3Vp-p, Negative
Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω)
Digital Signal Transmission System  TMDS (Single Link)
Video Signal Memory Analog Signal: 26
  
						

							30Chapter 5  Reference
Audio outputSpeaker output: 0.5 W + 0.5 W (8 Ω, THD+N: 10% or less)
Headphone output: 2mW + 2mW (32 Ω, THD+N: 3% or less)
Line input Input impedance 47 kΩ (typ.)
Input level: 1.0 Vrms (Max.)
Plug & Play  VESA DDC 2B/EDID structure 1.3
Dimensions
(Width) ×
(Height) ×
(Depth) Main unit 
(including Height 
adjustable Stand)
405 mm (15.9 inch) × 406.5 - 506.5 mm (16 - 19.9 inch) × 205 mm (8.1 inch)
Main unit  
(including EZ-UP 
stand) 405 mm (15.9 inch) × 347.7 - 507 mm (13.7 - 20 inch) × 246.8 - 277.6 mm (9.7 
- 10.9 inch)
Main unit  
(without stand) 405 mm (15.9 inch) × 334 mm (13.1 inch) × 61.5 mm (2.42 inch)
Mass Main unit  
(including Height 
adjustable Stand) Approx. 7.2 kg (15.9 lbs)
Main unit  
(including EZ-UP 
stand) Approx. 8.8 kg (19.4 lbs)
Main unit  
(without stand) Approx. 5.2 kg (11.5 lbs)
Movable range Height adjustable 
Stand Tilt: 30° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 100 mm (3.9 inch)
Rotation: 90° (clockwise)
EZ-UP stand Tilt: 25° Up, 0° Down
Swivel: 172° Right, 172° Left
Adjustable height: 154 mm (6.1 inch) (Tilt : 0°)
Rotation: -10° - 92° (clockwise)
Environmental 
Conditions Temperature
Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Storage temperature: –20 °C - 60 °C (-4 °F - 140 °F)
Humidity Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa