Eizo Flexscan Ev2023w Users Manual

1Chapter 3  Connecting Cables

●	To	set	input	signal	selection	[Input	Signal]
SettingFunction
AutoThe monitor recognizes the connector through which PC signals are input.When either PC is turned off or enters the power-saving mode, the monitor automatically displays signals of another PC.
ManualThe monitor detects only the PC’s signals currently displaying automatically. Select an active input signal with .
[Input	signal	setting]
(1) Choose  from the Adjustment menu, and press 
.
(2)  Choose  from...

Chapter 4  Troubleshooting

Chapter		 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
•  No-picture problems → See No.1 - No.2.
•  Imaging problems (digital input) → See No.3 - No.8.
•  Imaging problems (analog input) → See No.3 - No.12.
•  Other problems → See No.13 - No.18.
Problems Possible	cause	and	remedy
1.	 No	picture • Power indicator does not light. • 
Check whether the power cord is connected correctly. If 
the problem...

Chapter 4  Troubleshooting
ProblemsPossible	cause	and	remedy
.	 Afterimages	appear. • Afterimages are particular to LCD monitors. Avoid 
displaying the same image for a long time.
•  Use the screen saver or power save function to avoid 
displaying the same image for extended periods of time.
6.	 Green/red/blue/white	dots	or	defective	dots	remain	 on	the	screen. • 
This is due to LCD panel characteristics and is not a 
failure.
7.	 Interference	patterns	or	pressure	marks	remain	on	 the...

Chapter 4  Troubleshooting
ProblemsPossible	cause	and	remedy
18.	 (When	using	EcoView	Sense)
	
The	images	remains	to	be	displayed	when	you	
move	away	from	the	monitor.	The	images	does	not	
reappear	when	you	come	near	it. • 
Check the setting environment of the monitor. 
EcoView Sense may not work correctly in the following 
environments.
• There is something that reflects the light such as mirror 
or glass in front of the sensor.
•  The monitor is located in a place that receive direct...

Chapter 5  Reference

Chapter		 Reference
-1	 Attaching	an	Arm
The stand can be removed and replaced with an arm (or another stand) to be 
attached to the monitor. Use an arm or stand of EIZO option.
1	 When	using	the	monitor	with	"Portrait"	position,	change	the	
position	to	"Landscape".
2	 Lay	the	LCD	monitor	on	a	soft	cloth	spread	over	on	a 	stable	
surface	with	the	panel	surface	facing	down.
Attention
•  When attaching an arm or stand, 
follow the instructions of...

6Chapter 5  Reference

3	 Remove	the	stand.
●	 FlexStand
Remove the stand from the monitor while releasing the lock.
●	 TriStand
Prepare a screwdriver. Loosen the screw securing the unit and the stand with 
the screwdriver.
4	 Attach	the	monitor	to	the	arm	or	stand.
Secure the monitor to the arm or stand using the screws specified in the 
user’s manual of the arm or stand.
 

7Chapter 5  Reference

-	 Attaching	the	FlexStand
The once removed the FlexStand can be attached to the monitor again with the 
following procedures.
1	 Put	the	insertion	part	of	the	stand	in	the	slot	of	the	monitor.
At the time, use as a guide that the marks (1) on the stand match to the 
screw holes (2) of the monitor.


2	 Attach	the	stand	moving	the	monitor	toward	the	stand.
Make sure that the lock is latched with clicking sound shown in the figure 
below.
CorrectIncorrect...

8Chapter 5  Reference

-	 Attaching	the	TriStand
The once removed the TriStand can be attached to the monitor again with the 
following procedures.
1	 Lay	the	LCD	monitor	on	a	soft	cloth	spread	over	on	a	stable	
surface	with	the	panel	surface	facing	down.
2	 Put	the	insertion	part	of	the	stand	in	the	slot	of	the	monitor.
3	 Prepare	a	screwdriver.	Press	the	upper	part	of	the	stand	 against	the	unit	and	tighten	the	screw	with	the	screwdriver	to	
fix	the	stand	to	the	unit.
 

9Chapter 5  Reference

-	 Folding	the	TriStand
Perform the following procedures to remove the stand base and fold the stand 
when re-packing a monitor with a TriStand.
1	 Open	the	cable	holder.
2	 Adjust	the	monitor	to	its	lowest	position,	and	insert	a	pin	into	
the	stand.
3	 Lay	the	LCD	monitor	on	a	soft	cloth	spread	over	on	a 	stable	
surface	with	the	panel	surface	facing	down.
4	 Open	the	cover	of	stand	base.
Downloaded	from	ManualMonitor.com	Manuals 

0Chapter 5  Reference

5	 Rotate	the	stand	base	in	a	counterclockwise	direction	while	holding	down	the	protrusion,	and	then	remove	the	stand	base.
Downloaded	from	ManualMonitor.com	Manuals