Eiki Projector Lc Xb30 User Manual
Have a look at the manual Eiki Projector Lc Xb30 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31 Computer Input Press the SELECT button to display the Display area dialog box. Select the resolution at the Display area dialog box.Display area Adjust the horizontal area displayed by this projector. Press the Point 7 8buttons to decrease/increase the value and then press the SELECT button.Display area H Adjust the vertical area displayed by this projector. Press the Point 7 8buttons to decrease/increase the value and then press the SELECT button.Display area V With this function on, SXGA image is fully displayed at 4 : 3 aspect ratio. It is displayed at 5 : 4 aspect ratio with this function off. Full screen Reset Store Exit the PC Adjustment Menu. Quit To store adjustment data, move the red frame pointer to the Store icon and then press the SELECT button. Move the red arrow pointer to any of Mode 1 to 5 in which you want to store and then press the SELECT button. To reset the adjusted data, select Reset and press the OK button. The confirmation box will appear and then select [Yes]. All adjustments return to their previous figures. Mode free Vacant Mode Show values of “Total dots,” “Horizontal,” “Vertical,” “Display area H,” and “Display area V.” Close this dialog box. To store adjustment data To clear adjustment data To clear adjustment data previously set, move the red frame pointer to the Mode free icon and then press the SELECT button. Move the red arrow pointer to the Mode that you want to clear and then press the SELECT button.Display area Press the SELECT button at the Display area icon and the Display area dialog box appears. ✔Note: Auto PC Adjustment, Display area, Display area (H/V), and Full screen cannot be selected when 480i, 575i, 480p, 575p, 720p, 1035i, or 1080i is selected in the PC System Menu (p28). This Mode has parameters being stored. Computer Input
32 Computer Input Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Image Select Menu icon.1 2Press the Point d dbutton to move the red frame pointer to the level that you want to set and then press the SELECT button.Move the red frame pointer to the level and press the SELECT button. The level being selected. Image Select Menu Normal picture level preset on this projector.Standard Picture level with improved halftone for graphics.Real Picture level suitable for the image projected on a blackboard (Green). See above for further description.Blackboard(Green) Image Select Menu icon Select an image level among Dynamic, Standard, Real, Blackboard(Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. IMAGE button Dynamic Real Image 1 Image 2 Image 3 Normal picture level preset on this projector. Picture level with improved halftone for graphics. Standard Real Image 1~4 Image Level Selection Direct Operation Menu Operation Image 4 User preset image in the Image Adjust Menu (p33).Image 1~4 Blackboard(Green) Picture level suitable for the image projected on a blackboard (Green). This mode assists to enhance the image projected on a blackboard. This is mainly effective on a green colored board, not truly effective on a black colored board. Blackboard(Green) Picture level suitable for viewing picture in a bright room.Dynamic Picture level suitable for viewing picture in a bright room. Dynamic User preset image in the Image Adjust Menu (p33). Standard Remote Control IMAGE button
33 Computer Input Press the Point 7 8 buttons to adjust value. Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Image Adjust Menu icon.1 2Press the Point d dbutton to move the red frame pointer to the item that you want to adjust, and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8buttons.Move the red frame pointer to the item to be selected and then press the SELECT button. Image Adjust Menu Press the Point 7 button to decrease contrast and the Point 8 button to increase contrast. (From 0 to 63.) Press the Point 7 button to adjust image darker and the Point8 button to adjust image brighter. (From 0 to 63.)Contrast Brightness Press the Point 7 8button to obtain better balance of contrast. (From 0 to 15.)Gamma Image Level Menu Move the red frame pointer to any of Image 1 to 4 where you want to set and then press the SELECT button. Store icon Press the SELECT button at this icon to store the adjustment. Image Adjust Menu icon Press the Point 7button to lighten red tone and the Point 8 button to deepen red tone. (From 0 to 63.)White balance (Red) Press the Point 7button to lighten green tone and the Point 8 button to deepen green tone. (From 0 to 63.)White balance (Green) Press the Point 7button to lighten blue tone and the Point 8 button to deepen blue tone. (From 0 to 63.)White balance (Blue) Selected Image levelPress the Point 7 button or the Point8button for Color temp. level that you want to select. (XLow, Low, Mid, or High) Color temp. Press the Point 7button to soften the image and the Point 8 button to sharpen the image. (From 0 to 15.)Sharpness Image Level Adjustment To reset the adjusted data, select Reset and press the OK button. The confirmation box will appear and then select [Yes]. All adjustments return to their previous figures. Reset Store Exit the Image Adjust Menu. Quit To store the image data adjusted manually, move the red frame pointer to the Store icon and press the SELECT button. The Image Level Menu will appear. Move the red frame pointer to the Image 1 to 4 where you want to set and then press the SELECT button. A confirmation box will appear and then select [Yes]. Stored data can be called up by selecting Image in the Image Level Selection on page 32. Computer Input
34 Computer Input This projector has the picture screen resize function, which enables you to customize the image size. Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Screen Menu icon.1 Move the red frame to the function and press the SELECT button. Press the Point d dbutton and move the red frame pointer to the function that you want to select and then press the SELECT button.2 ✔Note: • This Screen Menu cannot be operated when 720p(HDTV), 1035i (HDTV), or 1080i (HDTV) is selected in the PC System Menu (p28). • The True and Digital zoom +/– cannot be selected when 480i, 575i, 480p, or 575p is selected in the PC System Menu (p28). • This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting to the projector. •The image data in other than XGA (1024 x 768) is modified to fit the screen size in initial mode. •The panning function may not operate properly if the computer system prepared in the PC Adjust Menu is used. •When Auto setup function is On and used any of the Auto setup function, Digital zoom +/- function will be canceled then the screen will go back to the normal size. •When selecting VGA, SVGA or SXGA in the Computer System Selection (p28) with adjusting Keystone function uppermost in the upward direction, the Digital zoom - function may not work. Screen Menu Screen Menu icon Screen Size Adjustment When the Digital zoom + is selected, the On-Screen Menu disappears and the message “D. Zoom +” is displayed. Press the SELECT button to expand the image size. And press the Point e ed d 7 8buttons to pan the image. The Panning function can work only when the image is larger than the screen size. A projected image can be also expanded by pressing the D.ZOOM ▲button on the remote control. To exit the Digital Zoom +/– mode, press any button except the D.ZOOM ▲/▼, SELECT, and Point buttons. Wide Digital zoom + Provide the image to fit screen size.Normal True When the Digital zoom – is selected, the On-Screen Menu disappears and the message “D. Zoom –” is displayed. Press the SELECT button to compress the image size. A projected image can be also compressed by pressing the D.ZOOM ▼button on the remote control. Digital zoom – Provide the image in its original size. When the original image size is larger than the screen size (1024 x 768), this projector enters “Digital zoom +” mode automatically. Provide the image to fit wide video aspect ratio (16 : 9) by expanding image width uniformly. This function can be used for providing a squeezed video signal at 16 : 9. To return to the normal screen select Normal from the Screen menu. POINTER Remote Control D.ZOOM e e button POINT buttons SELECT button D.ZOOM d d button
35 Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Input Menu icon. Press the Point d dbutton to move the red arrow pointer to Video and then press the SELECT button. The Source Select Menu will appear. 1 2 Move the pointer to Video and press the SELECT button. VIDEO Move the pointer to the source that you want to select and press the SELECT button. Source Select Menu (VIDEO) Input Menu Move the pointer to the source that you want to select and then press the SELECT button.3 When selecting Auto, the projector automatically detects incoming video signal, and adjusts itself to optimize its performance. Auto When video input signal is connected to the VIDEO jack, select Video.Video When video input signal is connected to the S-VIDEO jack, select S-Video.S-Video Video Computer 2 Computer 1 Input Source Selection (Video, S-Video) Direct Operation Menu Operation ✔Note: When Monitor out is selected at the Terminal item in the Setting Menu, Computer 2 is not displayed. (p44) ✳See Note at the bottom of this page. ✳ Input Menu icon Video Input Video Input REMOTE CONTROL TOP CONTROLPOWE AUTO SET UP INPUT SELECT MENU VOLUME– INPUT button VIDEO button ✔Note: • The projector selects the input source in the following priority. 1. S-video 2. Video INPUT button
36 Video Input Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Input Menu icon.1 Press the Point d dbutton to move the red arrow pointer to Computer 2, and then press the SELECT button. The Source Select Menu will appear. 2 Move the pointer to the correct input source and then press the SELECT button.3 Move the pointer (red arrow) to Computer 2 and press the SELECT button. Move the pointer to Component or RGB (Scart) and press the SELECT button. Source Select Menu Input Menu Input Menu icon Computer 1 Video Computer 2 Computer 1 Computer 2 Input Source Selection (Component, RGB Scart 21-Pin) Direct Operation Menu Operation When the input source is coming from video equipment connected to the COMPUTER IN 2/ COMPONENT IN/ MONITOR OUT terminal with a Component-VGA Cable, select Component. Component When the input source is coming from video equipment connected to the COMPUTER IN 2/ COMPONENT IN/ MONITOR OUT terminal with a Scart-VGA Cable, select RGB (Scart). RGB (Scart) ✔Note: • Component-VGA Cable and Scart-VGA Cable are optionally supplied. See page 61 for order. • Computer 2 is not displayed when the COMPUTER IN 2/COMPONENT IN/ MONITOR OUT terminal is set as Monitor out. (p44) Choose Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. ✳See Note at the bottom of this page. ✳ ✳ Computer 2 REMOTE CONTROL TOP CONTROLPOWE AUTO SET UP INPUT SELECT MENU VOLUME– INPUT button COMPUTER button INPUT button COMPUTER button
37 Video Input Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the AV System Menu icon.1 Video System Selection AV System Menu (Video or S-Video) AV System Menu (Component) Press the Point d dbutton to move the red arrow pointer to the system that you want to select and then press the SELECT button.2 If the projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.Move the pointer to a system and press the SELECT button.PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N The projector automatically detects incoming video signal, and adjusts itself to optimize its performance. If the projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i, and 1080i. Auto COMPONENT VIDEO SIGNAL FORMAT Video or S-Video Component The projector automatically detects incoming video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. Auto AV System Menu icon This box indicates the system being selected. Move the pointer to a system and press the SELECT button. AV System Menu icon This box indicates the system being selected. ✔Note: The AV System Menu cannot be adjusted when selecting RGB(Scart). Video Input
38 Video Input Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Image Select Menu icon.1 2Press the Point d dbutton to move the red frame pointer to the level that you want to set and then press the SELECT button.Move the red frame pointer to a level and press the SELECT button. The level being selected. Image Select Menu Normal picture level preset on this projector.Standard Picture level adjusted for the picture with fine tone.Cinema Blackboard(Green) User preset image in the Image Adjust Menu (p39, 40).Image1~4 Image Select Menu icon Select a desired image level among Dynamic, Standard, Cinema, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Normal picture level preset on this projector. Standard Picture level adjusted for the picture with fine tone. Cinema Blackboard(Green) User preset image in the Image Adjust Menu (p39, 40). Image 1~4 IMAGE button Dynamic Cinema Image 1 Image 2 Image 3 Image 4 Image Level Selection Direct Operation Menu Operation Picture level suitable for the image projected on a blackboard (Green). This mode assists to enhance the image projected on a blackboard. This is mainly effective on a green colored board, not truly effective on a black colored board. Picture level suitable for the image projected on a Blackboard (Green). See above for further description. Blackboard(Green) Picture level suitable for viewing picture in a bright room.Dynamic Picture level suitable for viewing picture in a bright room. Dynamic Standard Remote Control IMAGE button
39 Video Input Press the Point 7 8buttons to adjust value. Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the Image Adjust Menu icon.1 2Press the Point d dbutton to move the red frame pointer to the item that you want to adjust and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8buttons.Move the red frame pointer to the item to be selected and then press the SELECT button. Image Adjust Menu Press the Point 7button to decrease contrast and the Point 8 button to increase contrast. (From 0 to 63.) Press the Point 7button to adjust image darker and the Point 8 button to adjust image brighter. (From 0 to 63.)Contrast Brightness Press the Point 7 8buttons to obtain better balance of contrast. (From 0 to 15.)Gamma Press the SELECT button at this icon to display other items. Image Adjust Menu icon Press the Point 7button to lighten color and the Point 8button to deepen color. (From 0 to 63.) Press the Point 7 8buttons to obtain proper color. (From 0 to 63.) Color Tint Press the Point 7button to soften the image and the Point 8 button to sharpen the image. (From 0 to 15.)Sharpness Press the Point 7button to lighten red tone and the Point 8 button to deepen red tone. (From 0 to 63.)White balance (Red) Press the Point 7button to lighten green tone and the Point 8 button to deepen green tone. (From 0 to 63.)White balance (Green) Press the Point 7button to lighten blue tone and the Point 8 button to deepen blue tone. (From 0 to 63.)White balance (Blue) Press the SELECT button at this icon to display previous items. ✔Note: The Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N. Image Level Adjustment Press the Point 7 8buttons for Color temp. level that you want to select. (XLow, Low, Mid, or High) Color temp. Video Input
40 Video Input To store the adjustment data, move the red frame pointer to the Store icon and press the SELECT button. The Image Level Menu will appear. Move the red frame pointer to the Image Level 1 to 4 and then press the SELECT button. A confirmation box will appear and then select [Yes]. Stored data can be called up by selecting Image in the Image Level Selection on page 32. Image Level Menu Move the red frame pointer to an image icon to be set and then press the SELECT button. To reset the adjusted data, select Reset and press the OK button. The confirmation box will appear and then select [Yes]. All adjustments return to their previous figures. Reset Store Exit the Image Adjust Menu. Quit Interlaced video signal can be displayed in a progressive picture. Off . . . .Not activated. L1 . . . . .Select “L1” for an active picture. L2 . . . . .Select “L2” for a still picture.Progressive This function is effective on 3-2 pulldown video sources. With this function On, the projector reproduces pictures faithful to the original film quality. Film ✔Note: • Progressive cannot be selected when 480p, 575p, 720p, 1035i, or 1080i is selected. (p37) • Film can only be activated when selecting NTSC for Video System and L1/ L2 for Progressive and in any state shown below. 1. When selecting NTSC, NTSC4.43 PAL-M or 480i in the Video System Selection (p37). 2. When selecting Auto and signal is NTSC, NTSC4.43, PAL-M(Composite) or 480i(Component) in the Video System Selection (p37). • 3-2 Pulldown or Telecine transfer is the process of changing images from film mode to video mode. While film runs at 24 frames per second (fps), NTSC television signals (or video) have a run rate of 30fps so the 24 fps film needs to be speeded up to 30fps and transferred using a proper field pattern to get the best film-like images.Store icon