Eiki Projector Lc Xb29n User Manual

							11
Part Names and Functions
ON - OFF
POWER
AUTO SET UP
INPUT
WARNINGLAMP REPLACE
MENU
- VOLUME+ VOLUME
SELECT
qwetui
o
u LAMP REPLACE indicator
Turn yellow when the life of the projection lamp
draws to an end.  (pp.58, 61)
y WARNING indicator
Emit a red light when the projector detects 
abnormal condition.  This also blinks red when the
internal temperature of the projector exceeds the
operating range.  (pp.56, 61)
w POWER ON–OFF button
Turn the projector on or off.  (pp.21, 22)
r POWER indicator
Emit a red light until the projector gets ready to be
turned on.  It turns red when the projector is in the
stand-by mode.  It remains green while the
projector is under operation.  (pp.21, 22, 61)
t INPUT button
Select input source.  (pp.28, 29, 38, 39)
e MENU button
Open or close the On-Screen Menu.  (p.23)
o POINT (ed7 8 ) buttons
– Select an item or adjust the value in the On-
Screen Menu.  (p.23)
– Pan the image in Digital zoom + mode.  (p.37)
– Adjust the volume level. (Point 7 8buttons)     
(p.25)
q SELECT button
– Execute the selected item. (p.23)
– Expand or compress the image in Digital zoom 
mode.  (p.37)
Top Control
ry
iAUTO SETUP button 
Correct vertical keystone distortion and adjust
computer display parameters including Fine sync.,
Total dots and Picture position.  (pp.26, 45) 
						

							To ensure safe operation, please
observe the following precautions:
–Do not bend, drop, or expose the remote
control to moisture or heat.
–For cleaning, use a soft dry cloth. Do not
apply benzene, thinner, splay, or any
chemical material.
Remote Control
q
12
Part Names and Functions
i
r
!5
!1
@0
t
@1
!8
we
o
!0
!4
@3
!7
y
u
!2
!3
!9
@4
@2
!6
wPOWER ON-OFF button 
Turn the projector on or off.  (pp.21, 22)
rVIDEO button
Select the VIDEO input source.  (p.38)
tCOMPUTER button
Select the COMPUTER input source.  (pp.28, 29, 39)
oMENU button
Open or close the On-Screen Menu.  (p.23)
!2PAGE edbuttons
Scroll back and forth the pages on the screen when giving a presentation.  To use
these buttons, connect the projector and your computer with a USB cable.  (pp.10, 17)
!4D.ZOOM edbuttons
Zoom in and out the images.  (pp.27, 37)
yAUTO PC button
Automatically adjust the computer image to its optimum setting.  (pp.27, 31, 45)
!6IMAGE button
Select the image mode.  (pp.27, 34, 41)
!0FREEZE button
Freeze the picture on the screen.  (p.27) 
!7MUTE button
Mute the sound.  (p.25)
!8P-TIMER button
Operate the P-timer function.  (p.27)
!9NO SHOW button
Temporarily turn off the image on the screen.  (p.27)
uKEYSTONE button
Correct keystone distortion.  (pp.26, 46)
iPoint ed 7 8 ( VOLUME + / –
) buttons
– Select an item or adjust the value in the On-Screen Menu.  (p.23)
– Pan the image in the Digital zoom + mode.  (p.37)
– Adjust the volume level. (Point 7 8 buttons)  (p.25)
@1SELECT button
–  Execute the selected item.  (p.23)
–Expand or compress the image in Digital zoom mode.  (p.37)
!3LAMP CONTROL button
Select a lamp mode.  (pp.27, 51)
qL-CLICK buttonAct as the left mouse button for wireless mouse operation.  (p.14)
eSIGNAL EMISSION indicator
Lights red while the laser beam is being emitted from the laser light window or a
signal is being sent from the remote control to the projector.
!1LASER button
– Operate the Laser pointer function.  Laser beam is emitted while pressing this
button within 1 minute.  When using this laser pointer for more than 1 minute,
release the LASER button and press it again.  (p.13)
–Display the Pointer on the screen.  (p.13)
!5RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.” Set it to “ALL OFF” for
power saving when it is not used.  Slide this switch to RESET to initialize the
remote control code or switch Spotlight and Pointer to the Laser pointer function.
(pp.13, 14)
@0R-CLICK button
Act as the right mouse button for wireless mouse operation.  (p.14)
@2PRESENTATION POINTER button
Move a pointer of the projector or a pointer for wireless mouse operation.  (pp.13.14)
@3AUTO SET button
Correct vertical keystone distortion and adjust the PC display parameters. (pp.26, 45)
@4NETWORK button
Select the Network input or Memory viewer input.  See owners manual “Network
Set-up and Operation” and owners manual of Memory viewer (optionally available). 
						

							13
Part Names and Functions
Spotlight
Pointer Function
Pointer
Laser Light Window
Signal Emission Indicator
Laser Pointer Function
LASER button
PRESENTATION POINTER
button
MENU button
NO SHOW button
This remote control emits a laser beam from the laser light window. Press the LASER button to activate the
laser pointer. The signal emission indicator lights red and the red laser beam is emitted. If the LASER button is
pressed for more than one minute or if it is released, the laser light goes off.
The laser emitted is a Class IIlaser. Do not look into the laser light window or point the laser beam at yourself
or other people. The following is the caution label for the laser beam.
CAUTION:Use of controls, adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure. Never look directly into the laser light window while a laser
is emitted, otherwise eye damage may result. 
The caution label is put on the remote control.
You can move the Spotlight or Pointer of the projector with the remote control to emphasize a part of the
projected image.  
Press and hold the MENU and NO SHOW buttons for
more than 10 seconds to activate the Pointer function.
(The Laser pointer has switched to the Pointer function.)1
Press the LASER button on the remote control pointing
toward the projector. The Spotlight or Pointer is
displayed on the screen with the LASER button lighting
green. Then move the Spotlight or Pointer with the
PRESENTATION POINTER button. If the LASER button
does not light green and continues to emit a laser
beam, try the abovementioned procedure until the
LASER button lights green. 2
To clear the Spotlight or Pointer out the screen, press
the LASER button pointing toward the projector and see
if the LASER button lighting is turned off.
To switch to the Laser pointer again, press and hold the
NO SHOW and MENU buttons for more than 10
seconds or slide the RESET/ON/ALL-OFF switch to
“RESET” and then to “ON”.
When you reset the Pointer function, the remote control
code will be reset, as well. 3
✔Note:
•You can choose the size of Spotlight (Large/Middle/Small) and the
pattern of Pointer (Arrow/Finger/Dot) in the Setting Menu. See
“Pointer” on page 51.
Press and hold the MENU
and NO SHOW buttons for
more than 10 seconds. PRESENTATION POINTER
button
After the Laser pointer has
switched to the Pointer, use
the LASER button as the
Pointer function ON-OFF
switch. Press the LASER
button pointing toward the
projector and see if it lights
green. 
						

							PRESENTATION POINTER
button
R-CLICK button
L-CLICK button
While pressing the MENU
button, press the IMAGE
button number of times
corresponding to the
remote control code. 
MENU button
IMAGE button
RESET/ON/ALL-OFF
switch
Remote Control Code
Remote Control CodeNumber of Times
Pressing IMAGE
Button
Code 1 1
Code 2 2
Code 33
Code 44
Code 55
Code 66
Code 77
Code 88
Wireless Mouse Operation
The remote control can be used as a wireless mouse for your computer. Before operating the wireless mouse,
connect your computer and the projector with the supplied USB cable. See “Connecting to a Computer” on
page 17. When the Pointer function is used, the wireless mouse is not available. 
Acts as left (click) mouse
button while the projector
and a computer are
connected with a USB
cable.Move the pointer on the screen
with this button. 
Acts as right (click) mouse
button while the projector and a
computer are connected with a
USB cable.
The eight different remote control codes (Code 1–Code 8) are assigned to this projector. Switching the remote
control codes prevents interference from other remote controls when several projectors or video equipment
next to each other are operated at the same time. Change the remote control code for the projector first before
changing that for the remote control. See “Remote control” in the Setting Menu on page 51.
Press and hold the MENU and IMAGE buttons for
more than five seconds to switch between the codes.
The code switches sequentially for one pressing the
IMAGE button. See the list below.1
To initialize the remote control code, slide the RESET/
ON/ALL-OFF switch to “RESET,” and then to “ON.”
The initial code is set to Code 1.2
14
Part Names and Functions 
						

							15
Part Names and Functions
Adjustable Feet
To insure safe operation, please observe the following precautions :
●Use two (2) AAA or LR03 type alkaline batteries.
●Always replace batteries in sets.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture or heat.
●Do not drop the remote control.
●If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
●Risk of an explosion if battery is replaced by an incorrect type. 
●Dispose of used batteries according to the instructions.
Press the lid
downward and slide it.
Open the battery
compartment lid.Install new batteries
into the compartment.Replace the
compartment lid.
Two AAA size
batteries
For correct polarity (+
and –), be sure battery
terminals are in contact
with pins in
compartment.
12 3
Point the remote control toward the projector (Infrared
Remote Receiver) when pressing the buttons. Maximum
operating range for the remote control is about 16.4’ (5 m)
and 60 degrees in front of the projector.
Remote Control Operating Range Remote Control Battery Installation
Projection angle can be adjusted up to 10.0 degrees with the
adjustable feet. 
Lift the front of the projector and pull the feet lock latches
on both side of the projector upward.
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to a proper height, and tilt.
Keystone distortion can be adjusted automatically with the
Auto setup function or manually by using the remote control
or the menu operation (see pages 26, 45, 46).
Adjustable Feet
Feet Lock Latches
16.4’
(5 m)
60°
Remote control 
						

							Positioning the Projector
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the
screen.
✔Notes:
•The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain
the best image.
•All measurements are approximate and may vary from the actual sizes.
16
Installation
USB
 A
B
100150200
192
128
96
64300	XJEF

40
300	UFMF

43.0 (13.1m)
27.5 (8.4m)
18.4 (5.6m)
13.8 (4.2m)
Max. ZoomMin. Zoom
A : B  =  9 : 1
Screen Size
(W x H) mm
4 : 3 aspect ratio
Zoom (min)
40”
Zoom (max)
813 x 610
5.6 (1.7m)
3.6 (1.1m)
100”
2032 x 1524
14.4 (4.4m)
9.2 (2.8m)
150”
3048 x 2286
21.6 (6.6m)
13.8 (4.2m)
200”
4064 x 3048
28.9 (8.8m)
18.4 (5.6m)
300”
6096 x 4572 
43.0 (13.1m)
27.5 (8.4m)
(Inch Diagonal)
9.2 (2.8m)
(Center)
3.6 (1.1m) 
						

							17
Installation
ON ON
S-VIDEO IN  COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1DVI-IUSBSERVICE PORT MONITOR  OUT
COMPUTER IN 2 
/ COMPONENT IN
Cables used for connection 
• VGA Cable (Mini D-sub 15 pin) ✽
• DVI Cable ✽
• DVI-VGA Cable 
• USB Cable 
• Audio Cables ✽
(✽= Not supplied with this projector.)
External Audio Equipment
DVI-VGA
cable   DVI
cable ✽ USB cable 
Audio cable
(stereo) ✽
Audio cable ✽
(stereo) Monitor Output
or
Monitor Input USB port Audio Output
USB
COMPUTER/
COMPONENT
AUDIO IN
AUDIO OUT
(stereo)Audio Input
COMPUTER IN 2
/COMPONENT IN
/MONITOR OUT
Monitor Output
COMPUTER IN 1/ 
DVI-I 
VGA cable ✽
This terminal is switchable. Set up the
terminal as either Computer input or
Monitor output.  (See Page 49.)
Connecting to a Computer
Unplug the power cords of both the
projector and external equipment from
the AC outlet before connecting cables.
✔Notes:
•Input sound to the COMPUTER / COMPONENT AUDIO IN
terminal when using the COMPUTER IN 1 / DVI-I and the
COMPUTER IN 2 / COMPONENT IN / MONITOR OUT terminal
as input.
• When connecting the AUDIO OUT to external audio equipment,
the projectors built-in speaker is disconnected.
•When the cable is 
of the longer variety, it is advisable to use the
COMPUTER IN 1 / DVI-I and not the COMPUTER IN 2 /
COMPONENT IN / MONITOR OUT. 
•USB cable connection is needed when operating the computer with
the remote control or using the PAGE edbuttons on the remote
control. 
						

							18
Installation
S-VIDEO IN  COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTUSBSERVICE PORT MONITOR  OUT
COMPUTER IN 2 
/ COMPONENT INCOMPUTER  IN  1DVI-I
Cables used for connection  
• Video and Audio Cable (RCA x 3) ✽
• S-VIDEO Cable ✽
• Audio Cable ✽
(✽ = Not supplied with this projector.)
External Audio Equipment
Audio cable ✽
(stereo) VIDEO IN S-VIDEO S-video cable ✽
Video and audio cable ✽ Composite Video and Audio Output S-video Output
AUDIO INAudio Input
AUDIO OUT
(stereo) (R) (L) (R) (L) (Video)
(Video)
Connecting to Video Equipment
Unplug the power cords of both the
projector and external equipment from
the AC outlet before connecting cables.
✔Notes:
•When connecting AUDIO OUT to external audio equipment, the
projectors built-in speaker is disconnected.
•The S-VIDEO jack connection overrides the VIDEO jack connection
when selecting AUTO in the Input Menu (p.38). 
						

							19
Installation
S-VIDEO IN  COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTUSBSERVICE PORT MONITOR  OUT
COMPUTER IN 2 
/ COMPONENT INCOMPUTER  IN  1DVI-I
Cables used for connection
• Audio Cables ✽
• Scart-VGA Cable ✽
• Component Cable ✽
• Component-VGA Cable ✽
(✽= Not supplied with this projector.)  
External Audio Equipment
COMPUTER/
COMPONENT
AUDIO IN
Audio cable ✽
(stereo) Audio cable ✽
(stereo)
Audio Input Component Video Output
(Y, Pb/Cb, Pr/Cr) RGB Scart 21-
pin Output Audio Output
Scart-VGA
cable ✽
Component-VGA
cable✽
AUDIO OUT
(stereo)
Component
cable✽
COMPUTER IN 2
/COMPONENT IN /MONITOR OUT
This terminal is switchable. Set up the
terminal as either Computer input or
Monitor output.  (See Page 49.)
Connecting to Component Video Equipment
✔Notes:
•When connecting the AUDIO OUT to external audio equipment,
the projector’s built-in speaker is disconnected.
•See page 69 for ordering optional cables.Unplug the power cords of both the
projector and external equipment from
the AC outlet before connecting cables. 
						

							20
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100–120 V or
200–240 V AC and it automatically selects the correct input
voltage. It is designed to work with single-phase power
systems having a grounded neutral conductor. To reduce the
risk of electrical shock, do not plug into any other type of
power system.
If you are not sure of the type of power being supplied,
consult your authorized dealer or service station.
Connect the projector with all peripheral equipment before
turning the projector on.
CAUTION
For safety, unplug the AC power cord when the projector
is not in use. When the projector is connected to an outlet
with the AC power cord, it is in stand-by mode and
consumes a little electric power.
Connect the AC power cord (supplied) to the
projector.
The AC outlet must be near this equipment and
must be easily accessible.
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied the AC power cord does not match your AC outlet, contact your sales dealer.
To power cord
connector on your
projector.
Projector sideAC outlet side
Ground
To the AC outlet.(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
To the AC outlet.(200 - 240 V AC)