Eiki Projector Lc Xb27n User Manual

							41
Video Input
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the AV System Menu icon.1
Video System Selection
AV System Menu (Video or S-video)
AV System Menu (Component)
Press the Point edbuttons to move the red arrow
pointer to the system that you want to select and then
press the SELECT button.2
If the projector cannot reproduce proper video image, it is
necessary to select a specific broadcast signal format
among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-
N.
Move the pointer to a
system and press the
SELECT button.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
The projector automatically detects incoming video signal,
and adjusts itself to optimize its performance.
If the projector cannot reproduce proper video image, it is
necessary to select a specific component video signal
format among 480i, 575i, 480p, 575p, 720p, 1035i, and
1080i. Auto
COMPONENT VIDEO SIGNAL FORMAT Video or S-video
Component
The projector automatically detects incoming video system,
and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system
manually. AutoAV System Menu icon 
Selected system is 
displayed.
Move the pointer to a
system and press the
SELECT button. AV System Menu icon 
Selected system is 
displayed.
✔Note:
The AV System Menu cannot be selected when selecting RGB(Scart).
Video Input 
						

							42
Video Input
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Image Select Menu icon.1
2Press the Point edbuttons to move the red framed
pointer to the level that you want to set and then press
the SELECT button.Move the red framed pointer to a
level and press the SELECT
button.
The level being selected.
Image Select Menu
Normal picture level preset on this projector.Standard
Picture level adjusted for the picture with fine tone.Cinema
Blackboard(Green)
User preset image in the Image Adjust Menu (p43, 44).Image1~4
Image Select 
Menu icon
Select a desired image level among Dynamic, Standard,
Cinema, Blackboard (Green), Image 1, Image 2, Image 3,
and Image 4 by pressing the IMAGE button on the remote
control.
Normal picture level preset on this projector.   Standard
Picture level adjusted for the picture with fine tone.
Cinema
Blackboard(Green)
User preset image in the Image Adjust Menu (p43, 44). Image 1~4
IMAGE button
Dynamic
Cinema
Image 1
Image 2
Image 3
Image 4
Image Level Selection 
Direct Operation
Menu Operation
Picture level suitable for the image projected on a
blackboard.
This mode assists to enhance the image projected on a
blackboard.  This is mainly effective on a green colored
board, not truly effective on a black colored board.
Picture level suitable for the image projected on a
Blackboard.  See above for further description.
Blackboard(Green)
Picture level suitable for viewing picture in a bright room.Dynamic
Picture level suitable for viewing picture in a bright room. Dynamic
Standard
Remote Control
IMAGE
button 
						

							43
Video Input
Press the Point7 8
buttons to adjust the value.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Image Adjust Menu icon.1
2Press the Point edbuttons to move the red framed
pointer to the item that you want to adjust and then
press the SELECT button.  The level of each item is
displayed.  Adjust each level by pressing the Point
7
8
buttons.
Move the red framed
pointer to the item you
want to adjust and then
press the SELECT button.
Image Adjust Menu
Press the Point 7button to decrease the contrast and the
Point 8button to increase contrast.  (From 0 to 63.)
Press the Point 7button to adjust the image darker and the
Point 8button to adjust the image brighter.  (From 0 to 63.) Contrast
Brightness
Press the SELECT button
at this item to display other 
items.
Image Adjust Menu icon
Press the Point 7button to lighten the color and the Point
8 button to deepen the color.  (From 0 to 63.)
Press the Point7 8buttons to obtain a proper color.  (From
0 to 63.)Color
Tint
Press the Point 7button to lighten the red tone and the
Point 8 button to deepen the red tone.  (From 0 to 63.) White balance (Red)
Press the Point 7button to lighten the green tone and the
Point 8button to deepen the green tone.  (From 0 to 63.) White balance (Green)
Press the Point 7button to lighten the blue tone and the
Point 8button to deepen the blue tone.  (From 0 to 63.) White balance (Blue)
Press the SELECT
button at this item to
display previous items.
✔Note:
•The Tint cannot be selected when the video system is PAL, SECAM,
PAL-M, or PAL-N.  (p41)
•After adjusting any of the White balance Red, Green or Blue, the
Color temp. will change to Adj..
Image Level Adjustment
Press the Point7 8buttons for Color temp. level that you
want to select. (XLow, Low, Mid, or High) Color temp.
Video Input 
						

							44
Video Input
To store the adjusted data, select Store and press the
SELECT button.  Select a level from Image 1 to 4 with the
Point ed buttons and press the SELECT button.  A
confirmation box will appear and then select [Yes]. 
Stored data can be called up by selecting Image in the
Image Level Selection on page 42.
Image Level Menu
Move the red framed pointer to
an image item to be set and
then press the SELECT button.
To reset the adjusted data, select Reset and press the
SELECT button.  The confirmation box will appear and then
select [Yes].  All adjustments will return to their previous
figures.  
Reset
Store
Exit the Image Adjust Menu.
Quit
✔Note:
Noise reduction and Progressive cannot be selected when 480p,
575p, 720p, 1035i, or 1080i is selected.  (p41)
Store  
item
Interlaced video signal can be displayed in a progressive
picture.  Select one of the following.
Off...........disabled.
L1 ............Select “L1” for an active picture.
L2 ............Select “L2” for a still picture.
Film .........Select “Film” for watching a film.  
With this
function, the projector reproduces pictures
faithful to the original film quality. Progressive
Noise  reduction
Noise interference on the screen can be reduced.  Select
one of the following to get smoother images.
Off...........disabled.
L1 ............lower reduction 
L2 ............higher reduction
The confirmation box
will appear and then
select [Yes].
Press the Point7 8buttons to obtain better balance of
contrast.  (From 0 to 15.)Gamma
Press the Point 7button to soften the image and the Point
8button to sharpen the image.  (From 0 to 15.)Sharpness 
						

							45
Video Input
This projector has the picture screen resize function, which enables you to customize the image size.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Screen Menu icon.
Press the Point edbuttons and move the red framed
pointer to the function that you want to select and
then press the SELECT button.
1
2Move the red framed pointer to a
function and press the SELECT
button.
Screen Menu
Screen Menu icon
Provide the image at a wide screen ratio of 16 : 9.Wide
Provide the image at a normal video aspect ratio of 4 : 3.Normal
Screen Size Adjustment
✔Note:
Screen Menu cannot be operated when 720p, 1035i, or 1080i is
selected in the AV System Menu (p41).
Video Input 
						

							46
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Setting Menu icon.1
2
Language
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese,
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian,
Russian, Chinese, Korean, or Japanese.
Set the red framed
pointer to the item
and press the
SELECT button.
Press the Point edbuttons to move the red framed
pointer to the item that you want to set and then press
the SELECT button.  The Setting dialog box appears.Press the SELECT button at
Language item, the
Language Menu will appear.
Setting Menu (Language)
Setting Menu
icon
Setting
Setting
This projector has Setting menu that allows you to set up
the other various functions described as follows;
Press the
SELECT button at
this item to close
the dialog box.
Auto setup
This function enables Auto Keystone correction and Auto
PC adjustment by pressing the AUTO SETUP button on the
top control or the AUTO SET button on the remote control.
Settings for those functions can be altered as follows:
Auto PC Adj.
On  . . . . . .enables Auto PC Adjustment when pressing
the AUTO SET button on the remote control or
the AUTO SETUP button on the top control.
Off  . . . . . .disables Auto PC Adjustment.
Auto Keystone
Auto . . . . . always works and corrects keystone distortion
according to the projectors tilt.
Manual  . . .works only when pressing the AUTO SET
button on the remote control or the AUTO
SETUP button on the top control.
Off  . . . . . .disables Auto Keystone.
✔Note:
•Auto PC Adj. and Auto Keystone cannot be set Off at the same
time. 
•Auto Keystone corrects vertical distortion only, not correct
horizontal distortion.
•The Auto Keystone cannot work when Ceiling feature is On in the
Setting menu.  (p50)
•Perfect correction of the image distortion cannot be ensured with
the Auto setup function.  If the distortion is not corrected properly
by pressing the AUTO SETUP/ AUTO SET button, adjust manually
by pressing the KEYSTONE button on the remote control or
selecting Keystone in the Setting menu.  (See p25, 47)
Auto setup
Select Auto setup and this
box appears.  Choose
desired setting for Auto
keystone and Auto PC adj.
with the Point 7 8button.
Press the SELECT button
at this item to display the
other languages. 
						

							47
Setting
Display
Press the Point7 8buttons to switch On/Off.  This function
decides to display On-Screen Displays.
On .........................Show all the On-Screen Displays.  Use 
this function when you want to project 
images after the lamp becomes bright 
enough.  Factory default setting is this 
mode.
Countdown off ......Show the input image instead of the  
countdown when turning on the
projector.  Use this function when you
want to project the image as early as
possible even when the lamp is not
bright enough.
Off .........................Do not show On-Screen Displays. 
except;
● On-Screen Menu 
●“Power off?” message ● P-Timer ●“No signal” message for Power management item (p50)● ”Please wait...” message● White arrows for True item in the Screen Menu (p37)Blue back
Press the Point7 8buttons to switch On/Off.  When this
function is “On,” a blue image is displayed while the input
signal is not detected. 
Keystone
This function corrects distortion of a projected image.
Select either Store or Reset with the Point
7 8 buttons, and
then press the SELECT button.  The keystone dialog box
will appear.  Correct keystone with the Point 
edbuttons.
(p25)
Store .........store the keystone correction even when the 
AC power cord is unplugged.
Reset ........reset the keystone correction when the AC 
power cord is unplugged.
Keystone
Setting 
						

							48
Setting
Capture
This function enables you to capture the image being
projected and use it for a start-up display or interval of
presentations.  
After capturing the projected image, go to the Logo
select function and set it to “User”.  Then the captured
image will be displayed when turning on the projector
next time or pressing the NO SHOW button.  (p28) 
To capture the image, select [Yes].  To cancel the
Capture function, select [No].  
✔Note:
•Before capturing an image, select Standard in the Image Select
Menu to capture a proper image.  (p35, 42)
•A signal from a computer can be captured up to XGA(1024 x
768).  A signal from video equipment can be captured except
for 720p, 1035i, and 1080i.
•When capturing the image that has been adjusted by the
Keystone function, the adjustment data is automatically reset
and the projector captures an image without keystone
adjustment. 
•When the Logo PIN code lock function is On, Capture menu
cannot be selected.   
•When starting to capture a new image, the previously stored
image is cleared even if you cancel the capturing.
Select [Yes] to capture
the projected image. 
Select [Yes] to
stop capturing.  
Capture Logo select
This function decides the start-up display as follows:
User ..........the image you captured  
Default ......the factory-set logo
Off.............countdown onlyLogo (Logo and Logo PIN code lock settings)
This function allows you to customize the screen logo with
Logo select, Capture, and Logo PIN code lock functions.
Logo select✔Note:
When On is selected in Logo PIN code lock function, Logo select and
Capture functions cannot be selected. 
						

							49
Logo PIN code lock Dialog Box
QuitPointer
Enter a Logo PIN code
Select a number by pressing the Point7 8buttons and
fix the number with the SELECT button.  The number
will change to ✳.  If you fixed an incorrect number,
move the pointer to Set or Clear once by pressing the
Point 
dbutton, then return to Logo PIN code.  Enter
the correct number again.
Repeat this step to complete entering a four-digit
number. 
When the four-digit number is fixed, the pointer will
automatically move to Set.  Press the SELECT button
so that you can change the Logo PIN code lock setting.
If you entered an incorrect Logo PIN code, Logo PIN
code and the number (✳✳✳✳) will turn red and
disappear.  Enter a correct Logo PIN code all over again.
After a correct Logo PIN code is entered, the 
following dialog box will appear.
Select On/Off by pressing the Point 
7 8
buttons or change the Logo PIN code.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit
number. Select Logo PIN code change with the Point
d button and press the SELECT button. Set a new Logo
PIN code.  
Be sure to note the new Logo PIN code and keep it at
hand.  If you lost the number, you could no longer
change the Logo PIN code setting.  For details on PIN
code setting, refer to relevant instructions of the PIN
code lock function on page 52, 53.
Logo PIN code lock
This function prevents an unauthorized person from
changing the screen logo.
Off........the screen logo can be changed freely from 
the Logo select menu.  (p48)
On ........the screen logo cannot be changed without 
the Logo PIN code.
If you want to change the Logo PIN code lock setting,
enter a Logo PIN code along the following steps. The
initial Logo PIN code is set 4321 at the factory.Logo PIN code lock
Setting
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE,
WRITE DOWN THE NEW PIN CODE IN COLUMN OF
THE LOGO PIN CODE NO. MEMO ON PAGE 70, AND
KEEP IT SECURELY.  SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE PROJECTOR CAN
NO LONGER BE OPERATED.
Setting 
						

							50
Setting
Ceiling 
Rear  Ceiling
When this function is “On,” the picture will be top/bottom
and left/right reversed.  This function is used to project the
image from a ceiling mounting the  projector.
Rear
When this function is “On,” the picture will be left/right
reversed.  This function is used to project the image to a
rear projection screen.
Terminal
The COMPUTER IN 2 / COMPONENT IN / MONITOR OUT
terminal on the back of the projector is switchable for
computer input or monitor output.  (See page 10)  Select
Computer 2 or Monitor Out with the Point 78buttons. 
Computer 2 ........computer input
Monitor Out .......monitor out
Terminal function is not available when selecting Computer
2 to the input source.  Change the input source to the
others (Computer1 or Video) so that the Terminal function
will be available.  (p29, 30, 39, 40)   
Power management
Time left before Lamp is off.
Press the SELECT button
at Power management and 
this box will appear.
Choose one of three
settings with the Point
7 8
buttons, and 
go to the timer with the
Point edbuttons and set
time with the Point
7 8
buttons.
Power management
For reducing power consumption as well as maintaining the
lamp life, the Power management function turns off the
projection lamp when the input signal is interrupted and no
button is pressed for a certain period.
When the input signal is interrupted and no button is
pressed for 30 seconds or more, the timer display with No
signal message will appear.  The countdown will start to
turn off the lamp.
Select one of the operations. 
Ready ...............When the lamp has been fully cooled 
down, the POWER indicator changes to
green blinking. In this condition, the
projection lamp will be turned on if the
input signal is reconnected or any button
on the top control or remote control unit
is pressed. 
Shut down......When the lamp has been fully cooled
down, the power will be turned off. 
Off . . . . . . . . . . .Power management function is off. 
Then set the countdown timer with the Point 7 8buttons.
Standby mode
This function is available when operating the projector via
the network.
Normal···· Supply the power to the network function even
after turning off the projector.  You can turn
on/off the projector via the network, modify
network environment and receive an e-mail
about projector status while the projector is
powered off.
Eco ..........Select Eco when you do not use the projector
via the network.  The projectors network
function will stop when turning off the projector.
Refer to the owners manual Network Set-up and
Operation supplied with this projector.✔Note:
When selecting Normal, the cooling fans will be
operating even if the projector is turned off.