Eiki Projector Lc Xb250w User Manual

							41
Image select Menu
Standard
Picture mode adjusted with fine tone.
Cinema
Image 1–4
Image Mode Selection 
Dynamic
Remote Control
IMAGE button
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
For  viewing  with  the  user  preset  image  mode  in  the  Image 
Adjust  Menu  (see  pages  42–43).  This  Image  memory  is 
provided  in  each  computer,  component,  S-video  and  video 
input source.
1
2
Press the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select Image  
select and then press the Point ► or the SELECT 
button.
Use the Point ▲▼ buttons to select  the desired item 
and then press the SELECT button .
Picture mode with improved halftone for graphics.
Real
Blackboard (Green)
For the image projected on a blackboard.
T h i s   m o d e   h e l p s   e n h a n c e   t h e   i m a g e   p r o j e c t e d   o n   a 
blackboard.  This  is  mainly  effective  on  a  green  colored 
board, not truly effective on a black colored board.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
IMAGE button
Dynamic
Real
Image 1
Image 2
Image 3
Image 4
Standard
Cinema
Blackboard(Green)
Colorboard
Select the desired image mode among Dynamic, Standard, 
Real, Cinema, Blackboard  (Green), Colorboard, Image 
1, Image  2, Image  3  and Image  4  by  pressing  the  IMAGE 
button on the remote control.
Video Input
Direct Operation
Menu Operation 
						

							42
Image Adjustment
1
2
Press the Point ◄ button to decrease the contrast; press the 
Point ► button to increase the contrast (from 0 to 63).
Press  the  Point ◄  button  to  decrease  the  brightness;  press  
the Point ► button to increase the brightness (from 0 to 63).
Contrast
Brightness
Use the Point ◄► buttons to select the desired Color temp. 
level (XLow, Low, Mid or High). 
Color temp .
Press the Point ◄ button decrease the intensity of the color; 
press  the  Point ►	button  increase  the  intensity  of  the  color 
(from 0 to 63).
Press  the  Point ◄►  buttons  to  adjust  the  tint  value  to  get  a 
proper color balance (from 0 to 63).
Color
Tint
Image adjust MenuPress the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select the Image 
adjust and then press the Point ► or the SELECT 
button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point ◄► buttons to 
adjust the setting value.
Selected Image mode
Use the Point◄►buttons 
to adjust the setting value.
 Note:
	 •	When	the	white balance Red, Green or Blue is adjusted, the Color temp . level will change to User.
	 •	Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N (p.40).
	 •	When	Blackboard(Green)	or	Colorboard	is	selected	in	Image	select,	Color temp . will change to Blackboard 
or Colorboard.
Video Input
Press the Point ◄ button to lighten R/G/B tone; press the 
Point ► button to deepen R/G/B tone (from 0 to 63).
white balance (Red/Green/Blue) 
						

							43
Use  the  Point ◄►  buttons  to  adjust  the  gamma  value  to 
obtain a better balance of contrast (from 0 to 15).
Gamma
Press  the  Point ◄  button  to  decrease  the  sharpness  of  the 
image;  press  the  Point ►  button  to  increase  the  sharpness 
of the image (from 0 to 15).
Sharpness
An  interlaced  video  signal  can  be  displayed  in  progressive 
mode. Select one of the following options.
 Off .........  Disabled.
 L1 ..........  For an active picture.
 L2 ..........  For a still picture.
 Film .......  For watching a film. With this function, the 
projector reproduces pictures faithful to the 
original film quality.
Progressive
Noise reduction
Noise  interference  on  the  screen  can  be  reduced.  Select 
one of the following options to get smoother images.
 Off .........  Disabled.
 L1 ..........  Lower reduction 
 L2 ..........  Higher reduction
 Note:
  Noise  reduction  and Progressive  cannot  be  selected 
when 480p, 575p, 720p, 1035i  or 1080i  is  selected 
(p.40).
To  reset  the  adjusted  data,  select Reset  and  press  the 
SELECT button. A confirmation box appears and then select 
y es. All adjustments will return to their previous figures. 
Reset
Store
To store the adjusted data, select Store and press the Point 
► button or the SELECT button. Use the Point ▲▼ buttons 
to  select  one  from Image  1 to 4  and  press  the  SELECT 
button. 
A  confirmation  box  appears  and  then  select ye s.  Stored 
data  can  be  called  up  by  selecting  an Image  (1–4)  in  the 
Image Mode Selection on page 41.
Store Menu
A confirmation box 
appears and then 
select yes .
Video Input 
						

							44
This projector has the picture screen resize function, which enables you\
 to customize the image size.
Screen Size Adjustment
Screen Menu1
2
 Note:
	 •	When	no 	signal 	is 	detected, 	Normal  is  set 
automatically  and  the  Aspect  dialog  box 
disappears.
	 •	The	adjustable 	range 	for 	Scale  H/V  and 
Position  H/V  is  limited  depending  on  the 
input signal.
Press the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select Screen and 
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons select the desired item and 
then press the SELECT button.
Provide the image to fit the screen size.
Normal
Full 
Provide the full screen image. 
wide (16:9)
Provide the image at the 16:9 wide screen ratio.
Zoom
Scale the image proportionally to fit the entire screen. Either 
side of image may go over the screen.
Custom
Provide the last stored aspect screen image. 
Adjust  the  screen  scale  and  position  manually  with  this 
function.
Press  the Point ►	 button	 at	Custom  and  the Custom  is 
displayed	 on	the	 screen,	 you	can	use	the	Point	 ▲▼ buttons 
to choose the item you want to adjust.
 Scale H/V ..........  Adjust the Horizontal/Vertical screen 
scale.
 H&V ...................  When  set  to On,  the  aspect  ratio  is 
fixed. The Scale  V  appears  dimmed  and 
becomes  unavailable.  Adjust Scale  H, 
then  the  screen  scale  is  automatically 
modified based on the aspect ratio. 
 Position H/V .....  Adjust  the  Horizontal/Vertical  screen 
position.
 Common ...........  Save the adjusted scale or position to all 
the  inputs.  Press  the  SELECT  button  at 
Common  to  display  a  confirmation  box. 
To  save  the  scale  or  position,  press  the 
SELECT  button  at ye s.  When Custom 
is selected, the saved scale or position is 
used.
 Reset .................  Reset  the  all  adjusted  values.  Press 
the  SELECT  button  at Reset  to  display 
a  confirmation  box.  To  reset,  press  the 
SELECT button at y es.
Custom adj .
Video Input 
						

							45
When this function is set to On, the picture will be top/bottom 
and  left/right  reversed.  This  function  is  used  to  project  the 
image from a ceiling-mounted projector.
Ceiling
When  this  function  is  set  to  On,  the  picture  will  be  left/right 
reversed.  This  function  is  used  to  project  the  image  from 
rear of the screen.
Rear
To  reset  the  adjusted  data,  select  Reset  and  press  the 
SELECT button. A confirmation box appears and then select 
Yes. All adjustments will return to their previous figures.
Reset
Keystone
This  function  is  used  to  adjust  keystone  distortion  of  the  
projected	image.	Use	the	Point	 ▲▼	buttons	 to	choose	 the	
item you want to adjust.
 Keystone
     
To  correct  keystone  distortion,  press  the  SELECT  button.  
Keystone 	appears 	on 	the 	screen. 	Use 	the 	Point 	▲▼	
buttons to correct keystone distortion (p.23).
 Store 
     
To  store  or  reset  the  keystone  correction,  press  the  
SELECT button.
    Store ............Keep the keystone correction even when  
                          the AC power cord is unplugged.
    Reset............  Release  the  keystone  correction  when  the 
AC  power cord is unplugged.Ceiling
Rear
Keystone
Video Input 
						

							46
Language
The language used in the On-Screen Menu is available in 
English,  German,  French,  Italian,  Spanish,  Portuguese, 
Dutch,  Swedish,  Finnish,  Polish,  Hungarian,  Romanian, 
Czech,  Russian,  Turkish,  Kazakh,  Vietnamese,  Chinese, 
Korean, japanese and Thai.
Setting Menu
Setting
Setting
Press  the  MENU  button  to  display  the  On-Screen 
Menu.  Press  the  Point ▲▼  buttons  to  select  the 
Setting  and  press  the  Point ►  or  the  SELECT  button 
to access the submenu items.
1
2Use  the  Point ▲▼  buttons  to  select  the  desired  item 
and  then  press  the  Point ►  or  the  SELECT  buttons  to 
access the selected item.
This  projector  has  a  Setting  menu  that  allows  you  to  set  up 
the other various functions described below.
Language
Menu position
This function is used to change the position of the 
On-Screen Menu. Select Menu position and press the  
SELECT button. 
The Menu position changes each time you press the 
SELECT button as follows.
the center  the bottom left  the bottom right  the top 
left  the top right  the center .....
3Use  the  Point ▲▼  buttons  select  the  desired  item  and 
then press the SELECT button. 
						

							47
 Note:
	 •	Auto  Keystone  corrects  vertical  distortion  only, 
not correct horizontal distortion.
	 •	The	Auto  Keystone  function  cannot  work  when 
the Ceiling  feature  is  set On  in  the  Setting  menu 
(pp.37, 45).
	 •	Perfect 	correction 	of 	the 	image 	distortion 	cannot	
be  ensured  with  the  Auto  setup  function.  If  the 
distortion  is  not  corrected  properly  by  pressing 
the  AUTO  SETUP  or  AUTO  SET  button,  adjust 
manually  by  pressing  the  KEYSTONE  button  on 
the  remote  control  or  selecting Keystone  in  the 
Setting menu (pp.23, 37, 45).
	 •	Fine  sync, Total  dots, Horizontal  and Vertical 
p o s i t i o n   o f   s o m e   c o m p u t e r s   c a n n o t   b e   f u l l y 
adjusted  with  the  Auto  PC  Adjustment  function. 
When  the  image  is  not  provided  properly  with 
this  operation,  manual  adjustments  are  required 
(pp.31-32).
Auto setup
Input search
This  function  detects  the  input  signal  automatically.  When 
a  signal  is  found,  the  search  will  stop.  Use  the  Point ▲▼ 
buttons to select one of the following options.
Off ...........  Input search will not work.
On1.......... Input search works when.
  – Pressing the AUTO SETUP button on the top 
control or the AUTO SET button on the remote 
control.
On2.......... Input search works under the following situation.
  – When  turning  on  the  projector  by  pressing  the 
ON/STAND-BY button on the top control or the 
remote control.
  – When  pressing  the AUTO  SETUP  button  on 
the top control or the AUTO SET button on the 
remote control.
  – When the current input signal is cut off.*
* If  the  No  show  or  Freeze  function  is  active,  cancel  it  to 
activate  the  Input  search.  It  is  also  unavailable  when 
On-Screen menu is displayed.
Auto PC adj .
On........Enables  Auto  PC  Adjustment  when  pressing        
the AUTO  SET  button  on  the  remote  control  or 
the AUTO SETUP button on the top control.
Off .......Disables Auto PC Adjustment.
 Auto Keystone 
Auto . . . . .Always works and corrects keystone distortion 
according to the projector's tilt.
Manual....Works  only  when  pressing  the  AUTO  SETUP 
button  on  the  top  control  or  the  AUTO  SET 
button on the remote control.
Off .......Disables Auto Keystone.
Auto setup
 Note:
	 •	While	Input search is set to On1 or On2, the status of 
Input and Lamp are displayed every time the signal is 
switched.
	 •	Only	the	last	selected	input	source	can	be	detected.
	 •	If	the	INPUT 	button	on	the	top	control	or	the	
COMPUTER 1/2 buttons, VIDEO or S-VIDEO or 
COMPONENT button on the remote control is pressed 
during Input search is in progress, Input search will stop 
and go back to the previous input signal.
	 •	Input search, Auto PC adj . and Auto Keystone cannot 
be set Off at the same time. 
This  function  enables  Input  search,  Auto  Keystone  correction 
and Auto  PC  adjustment  by  pressing  the AUTO  SETUP  button 
on  the  top  control  or  the  AUTO  SET  button  on  the  remote 
control. Settings for those functions can be altered as follows: 
Setting 
						

							48
Background
Select the background screen when no input signal is 
detected. Press the Point ▲▼ buttons to switch between 
each option.
 Blue ... Project a blue background
 User... Project an image captured in the Logo setting.
 Black . . Project a black background
This function decides whether to display On-Screen Displays.
 On ...........................  Show  all  the  On-Screen  displays. 
Use  this  function  when  you  want 
t o   p r o j e c t   i m a g e s   a f t e r   t h e   l a m p 
becomes  bright  enough.  The  factory 
default setting is in this option.
 Countdown Off....... Show  the  input  image  instead  of 
the  countdown  when  turning  on  the 
projector. Use this function when you 
want to project the image as early as 
possible  even  when  the  lamp  is  not 
bright enough.
 Off ...........................  Hide the On-Screen Displays except;
   On-Screen Menu
   Power off? (p.20)
   No signal for Power management  
      (p.51)
   Please wait ...
   Arrows for the True function in the  
         Screen Menu (p.35)
   P-Timer
Setting
Display
Logo (Logo and Logo PIN code lock settings)
Logo select
This  function  allows  you  to  customize  the  screen  logo  with 
Logo select, Capture, Logo PIN code lock and Logo PIN 
code change functions.
 Note:
    When On is selected in the Logo PIN code lock function, 
Logo select and Capture functions cannot be selected.
Logo select
This  function  decides  on  the  starting-up  display  from 
among following options. 
 Off ...........  Show the countdown display only.
 Default ....  Show the factory-set logo.
 User ........  Show the image you captured. 
						

							49
Capture
Capture
This  function  enables  you  to  capture  an  image  being 
projected  to  use  it  for  a  starting-up  display  or  interval  of 
presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select yes to capture the 
projected image.
After  capturing  the  projected  image,  go  to  the  Logo  select 
function  and  set  it  to User. Then  the  captured  image  will  be 
displayed the next time you turn on the projector.
To cancel the capture function, select yes in the "Quit?" 
confirmation box.
 Note:
	 •	Before 	capturing 	an 	image, 	select 	Standard  in  the 
Image  select  Menu  to  capture  a  proper  image  (pp.33, 
41).
	 •	The 	output 	image 	resolution 	from 	a 	computer 	can 	be	
supported up to the panel resolution (1024 x 768).
	 •	When 	capturing 	the 	image 	that 	has 	been 	adjusted 	by	
the Keystone function, the adjusted data is automatically 
reset  and  the  projector  captures  an  image  without 
keystone correction. 
	 •	When	Logo PIN code lock is set to On, capture cannot 
be selected.   
	 •	When 	starting 	to 	capture 	a 	new 	image, 	the 	previously	
stored image is cleared even if you cancel the capturing.
		•	When 	there 	is 	no 	captured 	image 	or 	it 	is 	interrupted	
while capturing an image, User can not be selected, you 
can only switch between Default and Off.
Logo PIN code lockThis function prevents an unauthorized person from 
changing the screen logo.
 On ...........  The screen logo cannot be changed without a 
Logo PIN code.
 Off ...........  The screen logo can be changed freely from 
the Logo Menu (p.48).
If  you  want  to  change  the Logo  PIN  code  lock  setting, 
press  the  SELECT  button  and  the  Logo  PIN  code  dialog 
box  appears.  Enter  a  Logo  PIN  code  by  following  the  steps 
below.  The  initial Logo  PIN  code  is  set  to  “4321”  at  the 
factory.
Logo PIN code lock
Setting 
						

							50
Enter a Logo PIN code
Use  the  Point ▲▼	buttons  to  enter  a  number.  Press  the 
Point ► button to fix the number and move the red frame 
pointer  to  the  next  box.  The  number  changes  to  “”.  If 
you fixed an incorrect number, use the Point ◄ button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
Repeat this step to complete entering a four-digit number.
After  entering  the  four-digit  number,  move  the  pointer  to 
Set.  Press  the  SELECT  button  so  that  you  can  start  to 
operate the projector.
If  you  entered  an  incorrect  Logo  PIN  code, Logo  PIN 
code  and  the  number  ()  will  turn  red  for  a 
moment. Enter the correct Logo PIN code all over again.
Logo  PIN  code  can  be  changed  to  your  desired  four-
digit  number.  Press  the  SELECT  button  to  select Logo 
PIN  code  change. Current logo  PIN  code  dialog  box 
appears,  use  the  Point ▲▼  buttons  to  enter  the  current 
code. The New Logo PIN code input dialog box appears. 
Set  a  new  Logo  PIN  code,  confirmation  box  appears, 
choose yes to set the new Logo PIN code.
Be  sure  to  note  the  new  Logo  PIN  code  and  keep  it  on 
hand. If you lost the number, you could no longer change 
the Logo PIN code setting. 
Use the Point ▲▼ buttons to switch On or Off, and then 
press the SELECT button to make a choice.
Change the Logo PIN code lock setting
Enter a Logo PIN code
CAUTION:
wHEN  yOU  HAVE CHANGED  THE LOGO  PIN  CODE, 
wRITE DOwN THE NEw  PIN CODE  IN COLUMN  OF 
THE  LOGO  PIN CODE  NO . MEMO  ON PAGE  77,  AND 
KEEP IT  SECUREL y .  SHOULD  THE  LOGO  PIN CODE 
BE LOST  OR  FORGOTTEN , THE   LOGO  PIN CODE 
SETTING CAN NO LONGER BE CHANGED .
Logo PIN code change
Logo PIN code change
Setting
After a correct Logo PIN 
code is entered, the following 
dialog box appears.
Change the Logo PIN code lock setting