Eiki Projector Lc X71 User Manual

							51
APPENDIX
This symbol on the nameplate means the product is Listed by Underwriters\
Laboratories Inc. It is designed and manufactured to meet rigid U.L. saf\
ety
standards against risk of fire, casualty, and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (E\
C).
Pixelworks ICs used.
Remote control does
not work.●Check the batteries.
● Check if the ALL-OFF switch on the remote control is set to “ON.”
● Make sure there is no obstruction in between the Infrared remote receive\
r of the projector
and the remote control.
● Make sure you are not too far from the projector when using the remote c\
ontrol.
Maximum operating range is 16.4’ (5 m).
● Check the remote control code in the remote control.
(See“SETTING” on page 41.)
Problem:Tr y  t h ese Solutions
Wireless mouse
function does not
work.●Check the cable connection between the projector and your computer.
● Check the mouse setting on your computer.
● Turn the projector on before turning on a computer.
WARNING:
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If the problem still persists  after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center. Specify the model number and explain the difficulty. We will advise you \
how to obtain service. 
						

							52
APPENDIX
Computer Input
MENU TREE
InputRGB (PC analog)Go to System(1)Input 1
Y, Pb/Cb, Pr/Cr
Computer Input/Video Input
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Monitor out
Video
RGB
Go to System(2)
Go to System(3)
Go to System(1)
Go to System(2)Video
Y, Pb/Cb, Pr/Cr
S-Video
Go to System(3)
Go to System(2)
System (1)
Input 2
Input 3
Mode 1
Mode 2
SVGA 1
SVGA 2
SVGA 3
Image SelectStandard
Real
Image 1
Image 10
ScreenNormal
True
Wide
Full
D.zoom +
D.zoom -
PC AdjustAuto PC adj.
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
Display area - H
Display area - V
Reset
Mode free
Store
Quit
0 - 31
Yes/No
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Quit
✽System displayed in the System Menu varies depending on the input signal\
. 
						

							53
APPENDIX
Video Input
System (2)Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System (3)Auto
1080i
1035i
720p
575p
480p
575i
480i
Image SelectStandard
Cinema
Image 1
Image 10
ScreenNormal
Wide
Computer Input/Vide Input
Image AdjustContrastBrightnessColorTintColor management
Auto picture controlColor temp.
Store
0 - 63
Off/L1/L2
MidLowXLow0 - 630 - 630 - 630 - 310 - 15Off/L1/L2Off/On/FilmYes/No
0 - 63
0 - 630 - 63
ColorGammaListColor M.Menu
All DelMenuColor M.
High
RedGreenBlueSharpnessGammaNoise reductionProgressiveReset
Image 10Quit
Image 1
Quit
SoundVolumeBuilt-in SPMuteQuit
Computer Input/Vide Input
SettingLanguage
Anamorphic
German
Chinese
Japanese
Quit
Store/Reset
Blue/User/Black
Off/Countdown Off/On
Logo select
Capture
Logo PIN code lock
Quit
On/Off
On/Off
English
Italian
French
Spanish
Portuguese
Dutch
Swedish
Russian
Korean
Keystone
Display
Logo
Ceiling
Rear
On/Off
Menu position
On/Off
Power management
0 - 63On/OffOn/Off
Background
On/Off
Logo PIN code change
Quit
Simple menu
Ready
Off
Shut down
1-30 Min.
Quit
On/Off
Auto/Normal/Eco
On-Start
Lamp control
Code 1Remote Control
Code 8
Quit
MouseUSB
Projector
Key lockSecurityOff
Projector
Remote Control
Quit
PIN code lockOff/On1/On2
PIN code change
Quit
Yes/NoLamp counter
Yes/NoFactory default
Quit 
						

							54
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
–––––––– (Interlace)
1024 x 768(Interlace)
ON-SCREENDISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
45.0060.00
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
XGA 111024 x 768
XGA 131024 x 768
XGA 141024 x 768
61.0075.70
XGA151024 x 768
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768(Interlace)
58.0372.00
SXGA 11152 x 864
SXGA 21280 x 1024
63.4879.35
SXGA 31280 x 1024
36.0087.17
SXGA 41280 x 1024
64.2070.40
SXGA 51280 x 1024
62.5058.60
SXGA 61280 x 1024
63.9060.00
SXGA 71280 x 1024
63.3459.98
SXGA 81280 x 1024
63.7460.01
SXGA 111152 x 900
71.6967.19
SXGA 121152 x 900
81.1376.107
SXGA 131280 x 1024(Interlace)
63.9860.02
SXGA 141280 x 1024(Interlace)
61.2065.20
71.4075.60
50.0086.00
720p–––––––– (Progressive)
50.0094.00
37.5050.00
XGA 11024 x 768
XGA 21024 x 768
XGA 31024 x 768
XGA 41024 x 768
48.3660.00
68.67784.997
XGA 61024 x 768
60.02375.03
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
SXGA 91280 x 1024
SXGA 101280 x 960
79.97675.025
60.0060.00
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
SXGA 181280 x 1024(Interlace)
63.3760.01
76.9772.00
61.8566.00
46.4386.70
SXGA 191280 x 102463.7960.18
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
575i–––––––– (Interlace)15.62550.00
480i–––––––– (Interlace)15.73460.00
1080i–––––––– (Interlace)
33.7560.00
1035i–––––––– (Interlace)33.7560.00
SVGA 10800 x 60032.7051.09
SXGA 201280 x 102491.14685.024
480p–––––––– (Progressive)31.4759.88
XGA 101024 x 76862.0477.07
1080i28.12550.00
SXGA+ 11400 x 105063.9760.19
SXGA+ 21400 x 105065.3560.12
WXGA 31376 x 76848.3660.00
WXGA 41360 x 76856.1672.00
XGA 1235.52286.96
575p–––––––– (Progressive)31.2550.00
SXGA+ 31400 x 105065.1259.90
WXGA 11366 x 76848.3660.00
WXGA 21360 x 76847.7060.00
MAC1280 x 96075.0075.08
MAC1280 x 102480.0075.08
Basically this projector can accept a signal from all computers with V-,\
 H-Frequency mentioned below, and less
than 140 MHz of Dot Clock.
720p–––––––– (Progressive)
UXGA31600 x 120087.5070.00
UXGA41600 x 120093.7575.00
UXGA11600 x 120075.0060.00
UXGA21600 x 120081.2565.00
SXGA 211400 x 105063.9060.00 
						

							55
APPENDIX
NOTE:Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
D-VGA640 x 48031.4759.94
D-480p720 x 480
(Progressive)31.4759.88
D-575p768 x 575
(Progressive)31.2550.00
D-SVGA800 x 60037.87960.32
D-XGA1024 x 76843.36360.00
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
D-WXGA11366 x 76848.3660.00
D-WXGA51368 x 76846.5050.00
D-1035i1920 x 1035(Interlace)33.7560.00
D-1080i1920 x 1080 (Interlace)33.7560.00
D-1080i1920 x 1080(Interlace)28.12550.00D-WXGA21360 x 76847.7060.00
D-WXGA31376 x 76848.3660.00
D-720p1280 x 720
(Progressive)37.5050.00
D-720p1280 x 720
(Progressive)45.0060.00
D-SXGA11280 x 102463.9860.02
D-SXGA21280 x 102460.27658.069
When a input signal is digital from DVI terminal, refer to the chart bel\
ow.
D-1080psf/301920 x 108033.7560.00
D-1080psf/251920 x 108028.12550.00
D-1080psf/241920 x 108027.0048.00
D-SXGA+ 11400 x 105063.9760.19
INDICATORS AND PROJECTOR CONDITION
Check the indicators for projector condition.  
• • • on• • • dim• • • off• • • blinking
The projector is OFF. (The AC power cord is unplugged.)
The projector is ready to be turned on with the POWER ON-
OFF button.
The Warning Temp. indicator blinks red to let you know the
internal temperature of the projector exceeds a normal level. If
the temperature goes up further, the projector will be turned
off automatically and the Ready indicator goes out. When the
projector is cooled down enough and the temperature returns
to normal, the READY indicator lights green and the projector
can be turned on again. (The WARNING TEMP. indicator
keeps blinking.) Check and clean the air filters.
Projector Condition
The projector is operating normally. 
The projector is cooled down enough and the temperature
returns to normal. When turning on the projector, the
WARNING TEMP. indicator stops blinking. Check and clean
the air filters.
LAMP
REPLACE
yellow
Indicators
READYgreenLAMPred
WARNING
TEMP.red
✽
✽
✽
✽
✳
Depending on the condition of signals and the type and length of cables,\
 these signals may not be properly viewed.✳
✳
✳ 
						

							56
APPENDIX
• • • on• • • dim• • • off• • • flashing
*When the projection lamp reaches its end of life, the LAMP REPLACE indic\
ator lights yellow. When this indicator
lights yellow, replace the projection lamp with a new one promptly. Rese\
t the Lamp replacement counter after
replacing the lamp.
The projector is in cooling mode. It cannot be turned on until
the READY indicator lights green. 
Projector ConditionLAMP
REPLACE
yellow
Indicators
READYgreenLAMPred
WARNING
TEMP.red
The projector detects an abnormal condition and cannot be
turned on. Unplug the AC power cord and plug it again to turn
on the projector. If the projector is turned off again, disconnect
the AC power cord and contact the dealer or the service
center for service and checkup. Do not leave the projector on.
It may cause electric shock or a fire hazard.
The projector is in the Power management mode. 
✽
✽
✽The temperature inside the projector is abnormally high. 
The lamp cannot light up. (The projector is preparing for
stand-by or the projection lamp is in cooling mode. The
projector cannot be turned on until the cooling process is
completed.)
The lamp cannot light up. (The lamp has been cooled down
enough and the projector is in stand-by mode and ready to be
turned on with the POWER ON-OFF button.)
✽
The projection lamp reaches its end of life.
Replace the lamp and then reset the Lamp replacement
counter. The indicator is turned off. 
						

							57
APPENDIX
TECHNICAL SPECIFICATIONS
Owner’s Manual (CD-ROM)
Quick Reference Guide
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
VGA Cable
USB Cable
Control Cable for Serial Port 
Lens Cap (LC-X71)
Lens Attachment
Lens Replacement And Installation Manual
PIN Code Label
Multi-media Projector
Accessories
1.3” TFT Active Matrix type, 3 panels
19.8 lbs (9.0 kg) LC-X71, 18.0 lbs (8.2 kg) LC-X71L
12.6” x 6.6” x 16.8” (319 mm x 170.8 mm x 435.5 mm) 
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
Up and Down
800 TV lines (HDTV)
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Horizontal Resolution
Built-in Speakers
Operating Temperature
Storage Temperature
LCD Panel System
300 watt typeProjection Lamp
0˚ to 10.5˚Feet Adjustment
Power Source : AA or LR6 ALKALINE Type x 2
Operating Range : 16.4’ (5 m)/±30˚
Dimensions : 2.0” x 1.4” x 7.6” (50 mm x 36 mm x 193 mm)
Net Weight : 0.35 lbs (160 g) (including batteries)
Laser Pointer : Class IILaser 
(Max. Output: 1mW/Wave length: 650±20nm)
Remote Control Transmitter
480i, 480p, 575i, 575p, 720p, 1035i, and 1080iHigh Definition TV Signal
H-sync. 15 k ~ 100 kHz, V-sync. 48 ~ 100 Hz
Motorized Lens Shift
DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog)\
 
and Stereo Mini Type Jack (Audio)Input 1 Jacks
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H/V, and V),
Stereo Mini Type Jack (Audio)Input 2 Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)\
and DIN 4-pin (S-Video)Input 3 Jacks
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remo\
te Jack 
and Pj-to NetDirector Connector Other Jacks
Adjustable from 31” to 400”Projection Image Size (Diagonal)
F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus (LC-X71)\
Projection Lens
4.6’ (1.4 m) ~ 48.3’ (14.7 m)Throw distance
AC 100 ~ 120 V (5.7 A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (2.7 A Max. Ampere), 50/60 Hz 
(Continental Europe and The U.K.)
Voltage and Power 
Consumption
● Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even thou\
gh 99.99% of the pixels are effective, a tiny fraction  of the pixels (0.01% or
less) may be ineffective by the characteristics of the LCD panels. 
● Each projector has its own characteristics.
When projecting with several projectors on the same screen or side by si\
de, you may recognize different white balance and color  uniformity on each
projector. 
						

							58
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINALS (ANALOG)
Terminal: HDB15-PIN 
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert. sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
Terminal: Mini DIN 8-PIN
12
345876
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS/CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal: DVI 24-pin 
1917
21018
31119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5
2
4
3
6
7
8
Pin ConfigurationT.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
APPENDIX
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
2
34 1
Pin Configuration
Pin Configuration 
						

							59
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those part\
s, specify the item name and its Type
No. to the sales dealer.
●DVI  Cable Type No. : KA-DV20
● HDB 15 pin-SCART 21 pin Cable Type No. : AH-98881
● Long Zoom Lens  Type No. : AH-23132
● Ultra Long Zoom Lens Type No. : AH-24241
● Short Zoom Lens Type No. : AH-23122
● Short Fixed Lens Type No. : AH-32011
● Remote Control Cable Type No. : POA-CA-RC30
● Pj-to NetDirector Type No. : PjNET-30
LENS REPLACEMENT
The lens of this projector can be replaced with other optional lens. Thi\
s feature enables you to use the projector
for wide variety of uses.
For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be
installed or replaced by well-trained sales or service engineers. Do not\
 attempt to install and replace the lens by
yourself as it may cause injury.
After installing the lens, attach the lens cap to the lens when setting \
up the projector.
Do not hold the lens when carrying or lifting the projector. It may caus\
e serious damage to the projector. 
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japa\
n Business Machine and Information
System Industries Association). The projector supports all commands def\
ined by PJLink Class 1 and is verified
conformance with PJLink Standard Class 1.
PJLink is a registered trademark of JBMIA.
PJ LINK NOTICE
EIKI Projector Input
RGB (AV HDCP)
RGB (PC analog)
RGB (PC digital)
RGB (Scart)
Video
Y, Pb/Cb, Pr/Cr
RGB
PJLink Input
DIGITAL 2
RGB 1
DIGITAL 1
RGB 2
VIDEO 1
VIDEO 2
Video
Y, Pb/Cb, Pr/Cr
VIDEO 3
VIDEO 4
RGB 3
VIDEO 5S-video
Input1
Input2
Input3
Parameter
11
12
31
32
21
22
13
23
24
25
To the sales and service engineer:
Referring to the attached lens replacement and installation manual, repl\
ace or install the lens properly. 
						

							60
Write down the PIN code number in the column below and keep it with this\
 manual securely. If you forgot or lost
the number and unable to use the projector, contact the service station.\
 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
* Should the four-digit number be
changed, the factory set number will
be invalid.
Put on the label below (supplied) in a prominent place of the
projector’s body while it is locked with a PIN code.
While the projector is locked with the PIN code...
PIN Code Lock No.
Logo PIN Code Lock No.
PIN CODE NUMBER MEMO
APPENDIX