Eiki Projector Lc X7 User Manual

11

Terminals and Connectors
r	R/C JACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (supplied).
e	USB CONNECTOR (Series B)
  USB connector is to used to service the projector.
i	S-VIDEO INPUT JACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.21).
q	SERIAL PORT IN TERMINAL
  If you control the projector by computer, you must 
connect a cable (not supplied) from your computer 
to this terminal.
w	SERIAL...

1

i	FOCUS button
 Adjust the focus.  (p.27)
w	ZOOM button
 Zoom in and out the images.   (p.27)
q	ON/STAND-By button
 Turn the projector on or off.  (pp.23,24)
o INPUT button
   Select an input source INPUT 1, INPUT 2, Input 3 or Input 4. (pp.31-33)
y	AUTO PC ADJ  . button
 Automatically adjust the computer image to its optimum setting.  (p.27)
r	   POINT buttons
  -  Select an item or adjust the value in  the On-
Screen MENU.  
   -  
Pan the image in DIGITAL ZOOM + mode. (p.40)
Side Control and...

1

Indicators
q
w
e
r
t
y
u
e	WARNING TEMP  . indicator
  This indicator flashes red when internal projector 
temperature is too high. (pp.65, 72-74)
u LAMP 1 REPLACE indicator
    Turn  orange  when  the  life  of  the  projection  lamp1 
draws to an end. (pp.61, 73)
q	LAMP Indicator
  This indicator is dim when the projector is turned 
on.  And bright when the projector is in stand-by 
mode. (pp.72-74)  
w	
READ y indicator
  This indicator lights green when the projector is 
ready to be turned...

Remote Control
Part Names and Functions
q
t
e
!0
i
!4
r
!5
!3
!1
w
y
u
o
!7
!2
!8
!6
!9
@0
e	LIGHT button
  Light the buttons on the remote control for about 10 
seconds.
r MENU button
  Open or close the On-Screen MENU.  (pp.25-26)
t POINT ed 7 8 buttons
   –  Select an item or adjust the value in The ON-SCREEN MENU.
   –Pan the image in DIGITAL ZOOM +/– mode. (p.40)
y LENS SHIFT button
  Select the LENS SHIFT function.  (pp.27, 29)
!5 FOCUS buttons
  Adjust the focus.  (p.29)
u ZOOM buttons
  Zoom in...

Remote Control Battery Installation
123
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Two AA size batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To ensure safe operation, please observe the following precautions :
 ● Use two (2) AA or LR6 type alkaline batteries.
  ● Always replace batteries in sets.
  ● Do not use a new battery with a used battery.
  ● Avoid contact with...

16

The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 52.
1
2
Remote Control Code
Part Names and Functions
Check the Reset Switch to...

17

Installation
Lens Installation
Before setting up the projector, install Projection Lens on the projector.
  Before installation, check where the projector is used and prepare a suitable lens. For the specifications of 
Projection Lens, contact sales dealer where you purchased the projector.
- Do not use the optional lens below for this projector  .  Otherwise damages may result .
    LENS MODEL NO  .  :  AH-101, AH-10
-  Lens installation and replacement should be made by...

18

Picture Level and Pitch Adjustment
Installation
ADJUSTABLE
FEET
REAR ADJUSTABLE
FEET (Refer to p.10)
Projection lens can be moved from side to side and up and down with the motor-driven lens shift function.  This 
function makes the positioning of images easy on the screen.(See page 27)
Lens Shift Adjustment
When the lens is shifted to top .
The display position can be 
shifted upward up to 50% 
elevation of the display.
When the lens is shifted to bottom .
The display position can be 
shifted...

19

Terminals of Projector
The projector has two replaceable Interface board slots. The projector's functions can be extended by installing 
the optional interface boards into the terminal slots. 2 vacant slots (Input 3 and 4) are provided in your 
purchasing the projector.  For the Optional Interface Boards, contact sales dealer where you purchased the 
projector.
Pull out  the interface board.
Remove 2 Screws from an interface board.1
2
Tighten screws to secure the interface board.
Replace  the...

0

Installation
Connecting to Computer
VGA Cable 
Monitor Output 
Desktop typeLaptop type
Terminals of
the projector
Monitor Output 
DVI Cable BNC Cable ✽
Monitor Output 
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
Cables used for connection 
• VGA Cable (D-sub 15 pin) *
• DVI Cable 
• BNC Cable (BNC x 5)    
 ( *One cable is supplied; Other cables are not supplied with this projector.)
GVH/HVRB
DIGITALANALOG