Eiki Projector Lc X6a User Manual

							11
Preparation
Top Control
LENS SHIFTMENU
CANCEL
SELECT ZOOM
FOCUSSHUTTERINPUT
INFORMATION AUTO PC ADJ.
POWER P
qwerty
oi
u
uINPUT buttonSwitches input sources. (p30)
yAUTO PC ADJ. button
Operates the Auto PC adjustment function. (p30)
eCANCEL buttonCancels the selection and returns to the previous menu.  
tINFORMATION buttonDisplays the projector information. (p30) 
wMENU buttonOpens or closes the On-Screen Menu. (p33, 34)
oPOWER ON-OFF buttonTurns the projector on or off. (p27, 28)
iSHUTTER buttonCloses and opens up the built-in shutter. (p29)
qLENS SHIFT button Activates the Lens shift function. (p29)
!0!1!2
!0SELECT button- Executes the item selected.
- Expand/compress the image in the Digital zoom +/–
mode. (p32, 33)
!1FOCUS button
Adjusts focus of the image. (p29)
!2ZOOM buttonAdjusts zoom of the image. (p29)
Preparation
rPoint buttons (e, d, 7, and 8)
- Navigate through the menu or adjust the value in the
On-Screen Menu. (p33, 34)
- Pan the image in the Digital zoom + mode. (p32) 
						

							12
Preparation
ANALOG OUT
INPUT 3 INPUT 1
INPUT 2
ANALOG IN
DIGITAL (DVI-D)
VIDEO/Y    Cb/Pb          Cr/PrG                B               R            H/V               V
VIDEO/Y   Cb/Pb     Cr/PrS-VIDEO
Terminals
q
w
er
eINPUT 3 terminals
VIDEO/Y, Cb/Pb, and Cr/Pr
Connect video or component output signal (Y, Cb/Pb,
and Cr/Pr) from video equipment to these jacks with a
video cable (RCA-type). (p23, 24)
S-VIDEO
Connect S-Video output signal from video equipment
to this jack. (p23)
rINPUT 2 terminals
VIDEO/Y, Cb/Pb, and Cr/Pr 
Connect video or component output signal (Y, Cb/Pb,
and Cr/Pr) from video equipment to these jacks with a
video cable (BNC-type). (p24)
G, B, R, H/V, and V
Connect RGB output signal from a computer with a
computer cable (5 BNC-type) to these jacks. (p22)
wANALOG OUT
This terminal can be used for analog signal output
incoming through the ANALOG IN terminal (INPUT 1).
Connect this terminal to the other monitor with a VGA
cable. (p22)
qINPUT 1 terminals
DIGITAL (DVI-D)  (HDCP compatible)
Connect digital output signal from a computer or
video equipment to this terminal with a DVI-D cable.
(p22, 23)
ANALOG IN
Connect analog output signal from a computer or a
video equipment (Component or RGB Scart) to this
terminal with a VGA cable, a Scart-VGA or a
Component-VGA cable. (p22) 
						

							13
Preparation
A built-in micro processor which controls this unit may occasionally
malfunction and needs to be reset. This can be done by pressing the RESET 
button with a pen, which will shut down and restart the unit. Do not use the
RESET function excessively.
q
erty
uSERIAL PORT INWhen controling the projector from a computer, connect
the computer to this terminal with a serial cross cable
(commercially available).
tUSB (Series B)This port is used for the projector maintenance.
ySERIAL PORT OUTThis terminal outputs signal from SERIAL PORT IN.
When controling more than two projectors from a
computer, connect the other projector to this terminal
with a serial cross cable (commercially available). 
eR/C JACKConnect the remote control to this jack with the wired
remote cable (not supplied)  to use the remote control as
wired. (p25)
✽
✽
rUSB Connect a USB mouse (commercially available) to
control On-Screen Menu.(p25)
Preparation
w
wINPUT 5 (Vacant for Optional Interface Board)
Optional interface board can be installed into this slot.
This input accepts digital signals only. (p21, 73)
u
qINPUT 4 (Vacant for Optional Interface Board)
Optional interface board can be installed into this slot.
(p21, 73) 
						

							14
Preparation
Remote Control 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOMFOCUS ON-OFF
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTE
VOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
q
w
u
i
e
r
y
!0
o
oZOOM buttonsAdjust zoom of the image. (p29)
rCONTROL PAD (semiconductive touchpad)
- Selects an item or adjusts the value in the On-Screen
Menu.
- Pan the image in the Digital zoom + mode. (p32)
wKEYSTONE buttonCorrects keystone distortion. (p31)uPOWER ON-OFF button Turns the projector on or off. (p27, 28)
eLENS SHIFT buttonActivates the LENS SHIFT function. (p29)iFOCUS buttonsAdjust focus of the image. (p29)
tWIRED REMOTE JACK
Connect the Wired Remote Cable (not provided) to this
jack.
Battery installation is required regardless of it is used as
wired or wireless. (p16, 25)
!0SELECT button
Executes the item selected. 
t
yD.ZOOM buttonActivates the D.Zoom +/– function. (p32)
qSHUTTER buttonCloses the built-in shutter for light blocking. (p29)
About Control Pad
The built-in Control Pad is a
semiconductive touchpad operated with
a light finger touch. Move your finger
up, down, right and left across the pad
to select the desired menu, adjust
values and operate various convenient
features. Refer to the following pages
for respective directions. 
						

							15
Preparation
!1SCREEN button
Selects screen sizes. (p31)
!2
INPUT 1-3 buttons
Selects input source (INPUT 1 - INPUT 3). (p30)
!0AUTO PC button
Operates the Auto PC adjustment. (p30)
qMENU button
Opens or closes the On-Screen Menu. (p33, 34)
wFREEZE button
Freezes the projected picture. (p31)
!4REMOTE RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.”
Set it to “ALL OFF” for power saving when it is not
used. Slide this switch to RESET by holding down the
CH and ID buttons at the same time to initialize the
Remote Control ID and CH. (p16)
u
P-TIMER button
Operates P-Timer function. (p31) 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
INPUT 4INPUT 1 
INPUT 2
INPUT 3 INPUT 5
REMOTE   RESET  ON   ALL OFF
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
q
e
!0
!1
t
y
o
!3
i
r
u!4
w
!2
eandrbuttons are unusable.
tCH buttonSwitches Remote Control Channel (CH). (p16)
yID button
Switches Remote Control ID. (p16)
iCANCEL buttonCancels the selection and returns to the previous menu.
(p33)
oINFO buttonDisplays the projector information. (p30)
!3INPUT 4-5 buttonsSelects input source (INPUT 4 - INPUT 5). (p30)
Preparation 
						

							16
Preparation
This wireless remote control uses radio frequency signal. You can switch four frequency channels prepared and select a
remote control ID from eight IDs. The Remote Control Channel selection prevents radio frequency interference from the
other equipment and the Remote Control ID selection allows you to operate several projectors with their respective remote
controls without mutual interference among those projectors.
Wired Remote Control Transmitter
The remote control can be used as a wired remote control. When
interference between the projector and other equipment occurs or
the projector is used in a place where the operation of radio
equipment is restricted, connecting the remote control and the
projector with the wired remote cable (POA-CA-RC30) separatery
supplied is recommended. (p73) Connected with the wired remote
cable, the remote control does not emit radio signal.
Remote Control Channel and ID Setup
Initial Remote Control Channel and ID are CH1 and ID1. When you
change the setting, set a Channel first, and then an ID.
Channel and ID settings for the remote control should be the
same as those for the projector. When changing the CH and ID
settings to the remote control, do it to the projector as well. Refer
to Remote Control  in Setting menu on page 51.
Should you be lost at which CH and ID are currently set, initialize
the Channel and ID once, and set them again.
Hold down the CH button and press the SELECT button.
The Remote Control Channel switches sequentially for one
pressing the SELECT button. (See Table1 on next page.) 
Press and hold the CH and ID buttons, and slide the
REMOTE RESET/ON/ALL-OFF switch to REMOTE RESET,
and then to ON. The initial Channel and ID are CH1 and ID1.
(p15)
1
MENUMENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
INPUT 4INPUT 1 
INPUT 2
INPUT 3 INPUT 5
REMOTE   RESET  ON   ALL OFF
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
While pressing the CH/ID
button, press the SELECT
button number of times
corresponding to the remote
control CH/ID. 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
ID button CH button
SELECT button
✔Note:
Remote Control Channel and ID cannot be initialized separately.   
Set the Remote Control Channel
Set the Remote Control ID
2
Hold down the ID button and press the SELECT button.  The
Remote Control ID switches sequentially for one pressing
the SELECT button.  (See Table2 on next page.) 
Initialize the Remote Control Channel and ID
Remote Control Transmitter 
						

							17
Preparation
Remote Control Battery Installation
To insure safe operation, please observe the following precautions:
Use (2) AA or LR6 type alkaline batteries.
Always replace the batteries in sets.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture, or heat.
Do not drop the remote control.
If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
Risk of explosion if battery is replaced by an incorrect type. 
Dispose of used batteries according to the instructions.  
Press the lid downward
and slide it.
Open the battery
compartment lid.Install new batteries
into the compartment.Replace the compartment
lid.
Two AA size alkaline
batteries
For correct polarity (+ and
–), be sure battery terminals
are in contact with pins in
the compartment.
12 3
✽ Default settingID 7
ID 8
Remote Control ID
ID 1 ✽ 
ID 2 
ID 3
ID 4
ID 5
ID 6
Remote Control CHRadio Frequency
CH 1 ✽ 2.472 GHz
CH 2 2.403 GHz
CH 32.446 GHz
CH 42.421GHz
Channel switches sequentially for
one pressing the SELECT button. ID switches sequentially for one
pressing the SELECT button. 
Table1: Remote Control Channel & Frequency
Table2: Remote Control ID
Preparation
Caution about Radio Wave
The remote control operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical
equipment (such as pacemaker), as well as amateur radio stations. 
Before operating the remote control, make sure no electromagnetic interference occurs and pay attention to the
following cautions.
1. Be sure that there are no other devices in the area that may use the same frequency band as the remote
control.
2.  If any other devices are causing radio interferences, change the communication frequency channel or
move to other location.
Caution in Wireless LAN Interference
Under wireless LAN environment based on IEEE 802.11b and IEEE802.11g, the remote control may not operate
properly due to radio interferences. The remote control is initially set to use 2.472 GHz band (CH1) corresponding
to several channels of wireless LAN.  
Should the remote control not operate properly due to radio interference, switch the communication frequency
channel to CH2. Yet the operating condition is not improved, try CH3 and CH4. In case of failure in every channel
operation, relocate other radio equipment using 2.4 GHz band away from the remote control and the projector. 
						

							18
Install the projector in a safe place.  Before installation, read Safety
Instructions thoroughly and check the installation place. Install the
projector in a place with sufficient strength to support the
projectors weight. Installation on an unstable stand, cart, or ceiling
may cause serious injury or accidents.  
Do not place the projector where is extremely hot and humid. Do
not place the projector where is dusty and smoky. When installing
the projector in dusty and smoky places or in a place for a long
period of time, installation with Smoke Resist Box (AH-69601)
separately supplied is recommended. (p73)
When moving or setting up the projector, check the
followings again: 
–  Be sure that the lens is securely installed into the
projector.
–  Be sure to replace Lens cap to protect lens
surface.  
–  Be careful not to hold or subject a lens to strong
forces. It may damage lens, cabinet, or
mechanical parts.
This projector is designed to project on a flat surface. Projector
should be perpendicular to the projection screen. Otherwise, the
projected image may be distorted. Keystone function allows you
to correct image distortions, but it should be considered that the
keystone correction may lower the image resolution. (p31)
Do not expose the projection screen to direct sunlight or
excessive ambient lighting. The projected image may get white-
tinged due to reflection and the best image quality may not be
obtained.  SCREEN
Positioning the Projector
Before setting up the projector, install optional lens in the
projector. Install the lens following the instructions in the Lens
Installation Manual provided. Ask the sales dealer for detailed
information of optional lens specifications.  
Do not move the projector with holding the lens mounted and its
peripheral part. It may cause serious damages to the projector and
the lens.
Lens Installation
Installation
Lens cap
Installation 
						

							19
Installation
Adjustable feet Lens shift feature is provided to move the position of the projected image vertically by 50% and horizontally by 10%
respectively without any image distortion.
✽Lens shift range varies depending on lens and projectors. The range in this manual is the case of LNS-W04.
Level Adjustable Feet
This projector has four level adjustable feet. The projection angle
can be adjusted by rotating each foot. Adjust the four feet to
obtain best position of the projected image and make the projector
stable.  
The projection angle is adjustable up to 3.65 degrees upward and
downward respectively by rotating front and back feet.  
The projector can project image vertically and horizontally in the
range of 360 degrees. For proper installation, refer to Setup In
Proper Directions on page 6.
Projection angle is adjustable up to 3.65 degrees
upward and 3.65 degrees downward by adjusting front
and back feet.
3.65°
3.65°
Lens Shift Adjustment
Installation
50%
50%10%10% 
						

							20
Installation
Connecting AC Power Cord
This projector uses nominal input voltages of 120 V or 200-240 V
AC. This projector automatically selects correct input voltage. It is
designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of the power being supplied.
Connect the projector with all peripheral equipment before turning
it on.  (Refer to pages 22 ~ 24 for connection.) 
Connect the AC power cord (supplied)
to this socket. The AC outlet must be
near this equipment and must be
easily accessible.
Main On/Off switch
AC power socket
CAUTION
For safety, unplug the AC power cord when the projector is not
in use. When this projector is connected to an outlet with the
AC power cord and the Main On/Off switch is on, it is in stand-
by mode and consumes a little electric power.
To the POWER CORD
CONNECTOR on the
projector.
Projector sideAC Outlet side
Ground
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below.  The proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
To the AC Outlet.
(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
To the AC Outlet.(200 - 240 V AC)