Eiki Projector Lc X50m User Manual

11
PREPARATION
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
Do not drop or bump a projector, otherwise damages or malfunctions may result.
When carrying a projector, use a suitable carrying case.
Do not transport a projector by using a courier or transport service in an unsuitable transport case.  This
may cause damage to a projector.  To transport a projector through a courier or transport service, consult
your dealer for best way.
MOVING PROJECTOR
Use Carry Handle when moving a Projector.
When...

12
CONNECTING PROJECTOR
S–VIDEO
R – AUDIO 4 – L
VIDEO/Y – Cb/Pb – Cr/Pr
RESET
CONTROL PORT 
USB
AUDIO 1
AUDIO 2INPUT 1
INPUT 2 / OUT
INPUT 3
INPUT 4R/C JACK
(
MONO)
R – AUDIO 3 – L
VIDEO/Y – Cb/Pb – Cr/Pr
(
MONO)
TERMINALS OF PROJECTOR
When controlling computer
with Remote Control Unit of
this projector, connect mouse
port of your personal computer
to this connector.  (Refer to
P13.)
Connect S-VIDEO output
from video equipment to this
jack.  (Refer to P14.)  
Connect an audio output
from video equipment...

13
CONNECTING PROJECTOR
S–VIDEO
R – AUDIO 4 – L
VIDEO/Y – Cb/Pb – Cr/Pr
RESETCONTROL PORT 
USB
AUDIO 1
AUDIO 2INPUT 1
INPUT 2 / OUT
INPUT 3
INPUT 4R/C JACK
(
MONO)
R – AUDIO 3 – L
VIDEO/Y – Cb/Pb – Cr/Pr
(
MONO)
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF ON ON
ON ON
ON ONOFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF1234 56
OFF OFF ON ON ON ON 21 MODE (1152 x 870)
CONNECTING TO COMPUTER
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
VGA
Cable...

14
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
S–VIDEO
R – AUDIO 4 – L
VIDEO/Y – Cb/Pb – Cr/Pr
RESET
CONTROL PORT 
USB
AUDIO 1
AUDIO 2INPUT 1
INPUT 2 / OUT
INPUT 3
INPUT 4R/C JACK
(
MONO)
R – AUDIO 3 – L
VIDEO/Y – Cb/Pb – Cr/Pr
(
MONO)
Video Source (example)
Video Cassette Recorder
Video Disc Player
S-VIDEO
Cable ✽
S-VIDEO
Output
Cables used for connection(✽= Cable is not supplied with this projector.)
Audio Cable
(RCA x 2) ✽
AUDIO IN
S-VIDEO
VIDEOComponent video output equipment.
(such as DVD...

15
BEFORE OPERATION
FOCUS BUTTON
Used to adjust focus. (P21)
AUTO PC ADJ. BUTTON
Use to operate AUTO PC
Adjustment function. (P25)
KEYSTONE BUTTON
Used to correct keystone
distortion. (P21, 37)
IMAGE BUTTON
Used to select image
level. (P28, 32)
  LOCK
FREEZE
SELECT D.ZOOM
MUTE
VOLUME-
MENU
NO SHOW
IMAGE
VOLUME+
KEYSTONE
LASER
P-TIMER
ZOOM
INPUT 1INPUT 1
INPUT 2INPUT 2
FOCUS
LENS
AUTO PCON-OFF
INPUT 3INPUT 3
INPUT 4INPUT 4
COLOR.M
OPERATION OF REMOTE CONTROL
ONALL OFF
ALL-OFF SWITCH
Left Side
When using...

16
BEFORE OPERATION
To insure safe operation, please observe following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at same time.
Do not use a new battery with an used battery.
Avoid contact with water or liquid.
Do not expose Remote Control Unit to moisture, or heat.
Do not drop Remote Control Unit.
If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
Danger of explosion if battery is incorrectly replaced....

17
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to open or close
MENU operation. (P18,
19)
MENU BUTTON
IMAGE BUTTON
READY INDICATOR
SELECT BUTTONPOWER ON–OFF BUTTON
INPUT BUTTON
WARNING TEMP. INDICATOR
LAMP INDICATOR
POINT (VOLUME + / – ) BUTTONS LAMP REPLACE INDICATOR
Used to select image
level.  (P28, 32)
Lights  green when  a
projector is ready to be
turned on.  And it
flashes green in Power
Management mode.
(P39)
Becomes dim when a
projector is turned on.
And bright when a
projector is in...

18
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-SCREEN
MENU.  Refer to following pages to operate each adjustment on
ON-SCREEN MENU.
2  MOVING POINTER
3  SELECT ITEM
Move pointer (✽see below) or adjust value of item by pressing
POINT button(s) on Top Control or on Remote Control Unit.
Select item or set selected function by pressing SELECT button.
OPERATING ON-SCREEN MENU
✽Pointer is icon on ON-SCREEN MENU to select item.  See fig-
ures on section...

19
BEFORE OPERATION
MENU BAR
FOR PC SOURCEPress MENU BUTTON while connecting to PC input source.
FOR VIDEO SOURCEPress MENU BUTTON while connecting to VIDEO input source.
PC SYSTEM MENU
Used to select
computer system.
(Refer to P23, 24)
SETTING MENU
Used to change
settings of projector
or reset Lamp
Replace Counter. 
(Refer to P37-40)
IMAGE SELECT MENU
Used to select
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P28)GUIDE WINDOW
Shows selected
item of ON-
SCREEN MENU.
SCREEN MENU
Used to...

20
BASIC OPERATION
TURNING ON PROJECTOR
Connect a projectors AC Power Cord into an AC outlet.  LAMP
Indicator lights RED, and READY Indicator lights GREEN.
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON.  LAMP Indicator dims, and Cooling Fans
start to operate. Preparation Display appears on a screen and
count-down starts. Signal from PC or Video source appears after
30 seconds.
Current Input position and Lamp mode status are also displayed
on screen for 5 seconds. (Refer to LAMP...