Eiki Projector Lc Wul100al User Manual

							Computer Input
Image adjust Menu
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons to select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value.
Note:
  When	White	balance	Red,	Green	or	Blue	is	adjusted,	Color temp.	will	change	to	Adj..
Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press the Point ► button to increase the brightness (from 0 to 63).
Press the Point ◄ button to lighten red tone; press the Point ► button to deepen red tone (from 0 to 63).
Press the Point ◄ button to lighten green tone; press the Point ► button to deepen green tone (from 0 to 63).
Press the Point ◄ button to lighten blue tone; press the Point ► button to deepen blue tone (from 0 to 63).
Use the Point ◄► buttons to select the desired Color temp. level (High, Mid, Low or XLow). 
Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15).
Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 31).
Use the Point ◄► buttons to adjust the setting value.
Selected Image mode
Press the Point ◄ button to lighten red/green/blue tone of the black level of an image; press the Point ► button to deepen red/green/blue tone of the black level of an image.
Image Adjustment
Contrast
Brightness
Color temp .
White balance (Blue)
Sharpness
Gamma
Iris
White balance (Red)
White balance (Green)
Offset (Red/Green/Blue)
This iris function effectively increase the contrast intensity. Press the Point ◄► buttons to select Off or On.Off ...... Disabled.On ...... Contrast is prioritized over brightness.
41 
						

							Select the desired screen size that conforms to the input signal source.Screen Menu
Provide the image within a screen size keeping its original aspect ratio.
Note:
		•	The	projector	cannot	normally	display	any	resolution	higher	than	1920	x	1200.
	 •	The	image	data	other	than	1920	x	1200	is	modified	 to	fit	the	 screen	 size	in	initial	mode.
	 •	Full,	Zoom, True, Custom adj. and	Digital zoom +/–	cannot	be	selected	when	no	signal	is	detected	in	the	PC	System	Menu.	(p.36)
1
2
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons select the desired item and then press the SELECT button.
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select ye s. All adjustments will return to their previous figures. 
To store the adjusted data, select Store and press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 10 and press the SELECT button. A confirmation box appears and then select ye s. Stored data can be called up by selecting an Image (1-10) in the Image Mode Selection on page 40.
A confirmation box appears and then select ye s.
Store
Computer Input
Reset
Store
Screen Size Adjustment
Normal
Provide the image in its original size. When the original image size is larger than the panel size (1920 x 1200) and 16:9 or 4:3 is selected in Screen aspect, the projector goes to the panning mode automatically.Use the Point ▲▼◄► buttons to pan the image. When adjusted, the arrows will turn red. When reaching to the correction limits, the arrows will disappear.
Scale the image proportionally to fit the entire screen. Either side of image may go over the screen.
True
Zoom
Provide the image to fit full screen size.
Full 
Provide the last stored aspect screen image. 
Custom
Provide the image at the 16:9 wide screen ratio.
Wide (16:9)
42 
						

							Computer Input
Adjust the screen scale and position manually with this function.Press the Point ► button or the SELECT button at Custom adj . and Custom adj . is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale H/V ........  Adjust the Horizontal/Vertical screen scale. H&V .................  When set to On, the aspect ratio is fixed. Scale V appears dim and becomes unavailable. Adjust Scale H, and then the screen scale is automatically modified based on the aspect ratio.  Position H/V  ... Adjust the Horizontal/Vertical screen position. Common .........  Save the adjusted scale to all the inputs. Press the SELECT button at Common to display a confirmation box. To save the scale, press the SELECT button at ye s. When Custom is selected, the saved scale is used. Reset ...............  Reset all the adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at ye s.
Note:
 •	When	no	signal	is	detected,	Normal is	set	automatically	and	the	 Aspect	dialog	box	disappears.	 •	The	adjustable	range	for	Scale H/V and	Position H/V	is	limited	depending	on	the	input	signal.
Custom adj .
Custom adj .
Select Digital  zoom  +.  The  On-Screen  Menu  disappears and D .  zoom  +  appears.  Press  the  SELECT  button  to expand  the  image  size.  Use  the  Point  ▲▼◄►  buttons  to pan  the  image. The  Panning  function  can  work  only  when the image is larger than the screen size.You can also enter the Digital zoom + mode by pressing the D.ZOOM button on the remote control.
You can also enter the Digital zoom - mode by pressing the D.ZOOM button on the remote control.
Select Digital zoom – . The On-Screen Menu disappears and D . zoom – appears. Press the SELECT button to compress image size. The projected image can be also compressed by pressing the D.ZOOM button on the remote control.  
To  return  to  the  previous  screen  size,  select  a  screen size  from  the  Screen  Size  Adjustment  Menu  or  select an  input  source  from  the  Input  Source  Selection  Menu (see pages 33-35) again or adjust the screen size with the D.ZOOM button.
Note:
 •	The	panning	function	may	not	operate	properly	if	the	stored	Mode	in	the	PC	adjust	Menu	is	used	(p.39).		•	The	minimum	compression	ratio	is	limited	depending	on	the	input	signal,	when	the	Keystone	function	is	working	or	when	the	custom	is	selected	for	the	screen	size.	 •	True	and	Digital zoom +/– cannot	be	selected	when	480i,	575i,	480p or	575p	is	selected	in	the	PC	System	Menu	(p.36).	 •	Digital zoom +/-	cannot	be	selected	when	True	is	selected.		•	Digital zoom – cannot	be	operated	when	Custom	is	selected.
Digital zoom +
Digital zoom -
43 
						

							Computer Input
This function is used to adjust keystone distortion of the  projected image. Use the Point ▲▼ buttons to choose the item you want to adjust.Keystone
This function returns all adjusted values to the factory default settings. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at ye s.
Ceiling 
Rear 
When this function is set to On, the picture will be top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector.
When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear of the screen.
Keystone
Ceiling
Rear
Reset
Adjust the Horizontal/Vertical keystone distortion of the  projected image.
Standard 
Corner correctionAdjust the corner distortion of the projected image.
Corner patternChoose a Corner pattern mode among Red, White, Blue, and Off.  
Store
   Store .... 
Keep the keystone correction even when the AC power cord is unplugged.
   Reset .... 
Release the keystone correction when the AC power cord is unplugged.
Press the KEYSTONE button on the remote control to switch the Standard (for Vertical/Horizontal) /Corner correction adjustment. The Standard or Corner correction adjustment dialog box appears. Use the Point ▲▼◄► buttons to correct the Standard or Corner distortion (p.31).
Screen aspect
This function is used to project the image to a 4:3 or 16:9 projection screen.Default (16:10) ....  16:10 is the aspect of the LCD panel. The original Screen Menu is available.16:9 ..................... Set to a 16:9 projection screen.4:3 ........................Set to a 4:3 projection screen.
Note:
-		Natural wide	cannot	be	selected	when	720p,	1035i,	1080i or	1080p	is	selected	on	 AV	System	Menu	(p.45).
-		When	the	16:9	function	is	selected,	Wide (16:9)	is	not	available	in	the	PC	and	 AV	screen	(pp.42,	49).
-		When	the	4:3	function	is	selected,	Natural wide	is	not	available	in	the	AV	screen	(p.49).	
44 
						

							If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PA L, SECAM, NTSC, NTSC 4 .43, PAL-M, and PAL-N.
The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance.When the Video System is 1035i, 1080i or 1080p, select the system manually.
If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p, 1035i, 1080i, and 1080p.
Video Jack or S-video Jack
The projector automatically detects an incoming video system, and adjusts itself to optimize its performance.When Video System is PAL-M or PAL-N, select the system manually.
Video Input
1
AV System Menu (Video or S-video)
AV System Menu (y, Pb/Cb, Pr/Cr)
2
Press the MENU button to display the On-Screen Menu.  Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select System and then press the Point ► or the SELECT button. 
3Use the Point ▲▼ buttons to select the desired system and then press the SELECT button.
Note:
The	AV	System	Menu	cannot	be	selected	when	selecting	RGB (Scart).
Video System Selection
Auto
y, Pb/Cb, Pr/Cr Jacks
PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
Auto
y, Pb/Cb, Pr/Cr SIGNAL FORMAT
45 
						

							Normal picture level preset on the projector. 
Picture level adjusted with fine tone.
User preset picture adjustment in the Image adjust Menu. (p.48)
Video Input
Image select Menu
1
2
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image select and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and then press the SELECT button.
Image Level Selection
Menu Operation
Standard
Cinema
Image 1–10
For viewing pictures in a bright room.
Dynamic
Natural picture level preset on the projector.  
Natural
* The factory default setting is Standard.
Direct Operation
The Image Selection function can be operated directly by pressing the IMAGE SEL. button on the remote control. the last stored image will be displayed on the screen for about 4 seconds.IMAGE SEL .button
46 
						

							1
2
Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press the Point ► button to increase the brightness (from 0 to 63).
Press the Point ◄ button to lighten red tone; press the Point ► button to deepen red tone (from 0 to 63).
Press the Point ◄ button to lighten green tone; press the Point ► button to deepen green tone (from 0 to 63).
Press the Point ◄ button to lighten blue tone; press the Point ► button to deepen blue tone (from 0 to 63).
Use the Point ◄► buttons to select the desired Color temp. level (High, Mid, Low or XLow). 
Press the Point ◄ button to decrease the intensity of the color; press the Point ► button to increase the intensity of the color (from 0 to 63).
Press the Point ◄► buttons to adjust the tint value to get a proper color balance (from 0 to 63).
Note:
	•	When	White	balance	Red,	Green	or	Blue	is	adjusted,	the	Color	temp.	level	will	change	to	Adj..	•	Tint cannot	be	selected	when	the	video	system	is	PA L,	SECAM,	PAL-M or	PAL-N (p.45).
Image adjust Menu
Selected Image mode
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value.
Use the Point ◄► buttons to adjust the setting value.
Video Input
Image Adjustment
Contrast
Brightness
Color
Tint
Color temp .
White balance (Green)
White balance (Red)
White balance (Blue)
Iris
This iris function effectively increase the contrast intensity. Press the Point ◄► buttons to select Off or On.Off ...... Disabled.On ...... Contrast is prioritized over brightness.
47 
						

							Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15).
Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 31).
An interlaced video signal can be displayed in progressive mode. Press the Point ◄► buttons to change the progressive scan mode. Off .............Progressive scan mode is Off. On  .............Progressive scan mode is On . Film ........... 
For watching a film. With this function,  
the projector reproduces pictures faithful to the original film quality.
Noise interference on the screen can be reduced. Press the Point ◄► buttons to change the noise reduction mode. Off  .............Noise reduction mode is Off. On  .............Noise reduction mode is On.
Note: 
	 •	Progressive cannot	be	selected	when	480p, 575p, 720p, or 1080p is	selected	(p.45).		•	Noise reduction cannot	be	selected	with	the	computer	input	and	when	the	video	signal	format	is 1080p	(p.45).
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select y es. All adjustments will return to their previous figures. 
To store the adjusted data, select Store and press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select one from Images 1 to 10 and press the SELECT button. A confirmation box appears and then select yes. Stored data can be called up by selecting an Image (1-10) in the Image Mode Selection on page 46.
A confirmation box appears and then select yes.
Store
Video Input
Press the Point ◄ button to lighten red/green/blue tone of the black level of an image; press the Point ► button to deepen red/green/blue tone of the black level of an image (from 0 to 63).
Offset (Red/Green/Blue)
Sharpness
Gamma
Noise reduction
Progressive
Reset
Store
Image adjust Menu
48 
						

							Note:
	 •		
When	no	signal	is	detected,	Normal	is	set	automatically	and	the	Aspect	dialog	box	disappears.	 •		
The	adjustable	range	for	Scale	H/V	and	Position	H/V	are	limited	depending	on	the	input	signal.	 •		Natural wide	cannot	be	selected	when	720p,	1035i,	1080i	or	1080p is	selected	on	 AV	System	Menu	(p.45).
Video Input
Custom adj .
1
2
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and then press the SELECT button.
Provide the image within a screen size keeping its original aspect ratio.
Provide the image at the 16:9 wide screen ratio.
Screen Size Adjustment
Normal
Wide (16:9)
Custom adj .
Scale the image proportionally to fit the entire screen. Either side of image may go over the screen.
Provide the image to fit full screen size.
Full 
Expand the right and left side of images naturally without changing the center areas.
Natural Wide
Zoom  
Custom
Provide the last stored aspect screen image. 
Adjust the screen scale and position manually with this function.Press the Point ► button at Custom adj . and the Custom adjustment menu is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust.
 Scale H/V …… Adjust the Horizontal/Vertical screen scale. H&V…………… When set to On, the aspect ratio is fixed. Scale V appears dimmed and becomes unavailable. Adjust Scale H, then the screen scale is automatically modified based on the aspect ratio.  Position H/V… Adjust  the  Horizontal/Vertical  screen position. Common……… Save the adjusted scale or position to all the inputs. Press the SELECT button at Common to display a confirmation box. To save the scale or position, press the SELECT button at "Yes", When Custom is selected, the saved scale or position is used. Reset………… Reset all the adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at yes.
49 
						

							Video Input
This function returns all adjusted values to the factory default settings. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at ye s.
Ceiling 
Rear 
When this function is set to On, the picture will be top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector.
When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear of the screen.
Keystone 
This function is used to adjust keystone distortion of the projected image. Use the Point ▲▼ buttons to choose the item you want to adjust.
Keystone
Adjust the Horizontal/Vertical keystone distortion of the  projected image.
Standard 
Corner correction
Adjust the corner distortion of the projected image.
Corner pattern
Choose a Corner pattern mode among Red, White, Blue, and Off.  
Store
    Store ... 
Keep the keystone correction even when the AC power cord is unplugged.
    Reset ... 
Release  the  keystone  correction  when  the AC power cord is unplugged.
Press the KEYSTONE button on the remote control to switch the Standard (for Vertical/Horizontal) /Corner correction adjustment. The Standard or Corner correction adjustment dialog box appears. Use the Point ▲▼◄► buttons to correct the Standard or Corner distortion.  (p.31) 
Ceiling
Rear
Reset
This function is used to project the image to a 4:3 or 16:9 projection screen.Default (16:10) ....  16:10 is the aspect of the LCD panel. The original Screen Menu is available.16:9 ..... Set to a 16:9 projection screen.4:3 .....   Set to a 4:3 projection screen.
Screen aspect
Note:
		-		When	the	16:9	function	is	selected,	Wide (16:9)	is	not	available	in	the	PC	and	 AV	screen	(pp.42,	49).		-		When	the	4:3	function	is	selected,	Natural wide	is	not	available	in	the	 AV	screen	(p.49).	
50