Eiki Projector Lc Wul100al User Manual

Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth. When the cabinet is...

The WARNING indicators show the state of the function which protects the proj\
ector. Check the state of the WARNING indicators and the POWER indicator to take proper maintenance. 
The projector is shut down and the WARNING TEMP . indicator is blinking red .
When the temperature inside the projector reaches acertain level, the projector will be automatically shut down to protect the inside of the projector. The POWER indicator is blinking while the projector is being cooled down. When the projector has...

Appendix
Before calling your dealer or service center for assistance, check the i\
tems below once again.
1. Make sure you have properly connected the projector to peripheral equipm\
ent as described on pages 19-21.2. Check the cable connection. Make sure that all computers, video equipmen\
t, and power cords are properly connected.3. Make sure that all power is switched on.4. If the projector still does not produce an image, restart your computer.5. If an image still does not appear, disconnect the...

Appendix
appears on the screen
–  Filter  is  out  of  scroll.  Replace  the  filter  cartridge  with  a  new  one  promptly.    (See pages 67-68)
The image is out of focus .
– Adjust the focus of the projector.– Check Projection Lens to see if it needs cleaning. Note:  Moving	the	projector	from	a	cool	temperature	location	to	a	warm	temperature	location	may	result	in	moisture	condensation	on	Projection	Lens.	In	such	cases,	leave	the	projector	OFF	and	wait	until	condensation	evaporates.–   Projecting...

Appendix
WARNING: High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector  or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem.  We  will  advise you how to obtain service.
The shutter does not work .- Check "Protection" or "Release key" of the Shutter function. (See p.6\
3)
The power is turned off...

Mode 10
InputRGB (PC analog)
Y, Pb/Cb,Pr/Cr
RGB (Scart)
HDMI
Network*
Video
RGB
Video
Y, Pb/Cb,Pr/Cr
S-video
Input 3
Input
H-sync freq.V-sync freq.
Information
ScreenLanguageLamp status
Power management
Remote control
Note:
 	The	Menu	display	varies	depending	on	the	input	signal.
Appendix
Volume
MuteOn/Off
Sound0-63Built-in SP
PIN code lockKey lock
SERIAL NO.
*  Network will be displayed only when an optional Pj-to NetDirector is attached.
Input 1
Input 2
Lamp counterFilter counter
Simple mode
On/Off...

Note:
The	Menu	display	varies	depending	on	the	input	signal.
System (2)AutoPA LSECAMNTSCNTSC 4.43PAL-MPAL-N
System (3)Auto
1080i1035i720p575p480p575i480i
Image select
Cinema
Appendix
ScreenNormal
Wide(16:9)Full
Zoom
RearCeiling
On/OffOn/Off
Custom adj.H & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Screen
Digital zoom +
Digital zoom -
Video Input
Image select
Screen
Image adjustContrastBrightness
Color temp.
Red
Gamma
Store
0–630–63
0–63
0–15
Image 1
Image 10
ResetYes/No
Sharpness0–31...

Appendix
SettingLanguage
Fan control
Blue/User/Black
Yes/No
12 languages providedMenu
Lamp control
Filter control
All/Front&Top/Top&Back/Front&Back/Front/Top/Back
Normal/Max
Power management
Background
RC sensor
ReadyOff
Shut down1–30 Min
On/OffDirect onPointer
On/Countdown Off/OffDisplay
Remote Control
Dot/Arrow/Finger
Yes/No
Management
Remote controlProjector
5 - 480 Min
Code 1~Code 8
On/Off
Computer Input/HDMI Input/Video Input
Logo select
Off
User
CaptureYes/NoOff/OnLogo PIN code changeLogo PIN code...

Check the indicators for the projector condition.  
Indicators
Projector ConditionPOWERgreenLAMPred
WARNINGTEMP.red
WARNINGFILTERorange
SHUTTERblue
LAMPREPLACEorange
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector.
The projector is operating normally.
(The shutter is open)
The projector is operating normally.
(The shutter is closed)
The projector is preparing for stand-by or the projection lamp is being...

The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWERgreenLAMPred
WARNINGTEMP.red
WARNINGFILTERorange
SHUTTERblue
LAMPREPLACEorange
The temperature inside the projector is elevated close to the abnormally high level.
The temperature inside the projector is abnormally high. The projector cannot be turned on. When the projector is cooled down enough and the temperature returns to normal, the POWER indicator lights green and the projector can be turned on. (The WARNING TEMP....