Eiki Projector Lc W5 User Manual

11
Terminals and Connectors
r	R/C JACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (supplied).
e	USB CONNECTOR (Series B)
  USB connector is to used to service the projector.
i	S-VIDEO INPUT JACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.21).
q	
SERIAL PORT IN TERMINAL
  If you control the projector by computer, you must 
connect a cable (not supplied) from your computer 
to this terminal.
w	 SERIAL...

12
i	FOCUS button
  Adjust the focus.  (p.27)w	ZOOM button
  Zoom in and out the images.   (p.27)
q	ON/STAND-B y button
  Turn the projector on or off.  (pp.23,24)
o INPUT  button
   Select an input source INPUT 1, INPUT 2, Input 3 
or Input 4. (pp.31-33)
y	AUTO PC ADJ  . button
  Automatically adjust the computer image to its 
optimum setting.  (p.27)
r	  POINT  buttons
  -  Select an item or adjust the value in  the On-
Screen MENU.  
   -  Pan the image in DIGITAL ZOOM + mode. (p.40)
Side Control and...

13
Indicators
qw e
r
t y
u e	
WARNING TEMP  . indicator
  This indicator flashes red when internal projector 
temperature is too high. (pp.65, 72-74)
u  LAMP 1 REPLACE indicator
    Turn  orange  when  the  life  of  the  projection  lamp1 
draws to an end. (pp.61, 73)
q	
LAMP Indicator
  This indicator is dim when the projector is turned 
on.  And bright when the projector is in stand-by 
mode. (pp.72-74)  
w	 READ y indicator
  This indicator lights green when the projector is 
ready to be turned on....

Remote Control
Part Names and Functions
q
t e
!0
i !4
r
!5!3
!1
w
y
u
o !7
!2
!8
!6
!9
@0
e	 LIGHT button
  Light the buttons on the remote control for about 10 
seconds.
r  MENU button
  Open or close the On-Screen MENU.  (pp.25-26)
t  POINT ed 7 8 buttons
   –  Select an item or adjust the value in The ON-SCREEN MENU.
   –Pan the image in DIGITAL ZOOM +/– mode. (p.40)
y  LENS SHIFT button
  Select the LENS SHIFT function.  (pp.27, 29)
!5  FOCUS buttons
  Adjust the focus.  (p.29)
u 
ZOOM buttons
  Zoom...

Remote Control Battery Installation
12 3
Open the battery 
compartment lid. Install new batteries into 
the compartment. Replace the 
compartment lid.
Two AA size batteries
For correct polarity (+ and –), 
be sure battery terminals are 
in contact with pins in the 
compartment.
To ensure safe operation, please observe the following precautions :
 ●
 Use two (2) AA or LR6 type alkaline batteries.
 ●  Always replace batteries in sets.
 ●  Do not use a new battery with a used battery.
 ●  Avoid contact with...

16
The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 52.
1
2
Remote Control Code
Part Names and Functions
Check the Reset Switch to...

17
Installation
Lens Installation
Before setting up the projector, install Projection Lens on the projector.
  Before installation, check where the projector is used and prepare a suitable lens. For the specifications of 
Projection Lens, contact sales dealer where you purchased the projector.
Positioning Projector
This projector is designed to project on a flat projection 
surface.
✔Note:
•  Brightness  in  room  has  a  great  influence  on  picture  quality.  
It  is  recommended  to  limit  ambient...

18
Picture Level and Pitch Adjustment
Installation
ADJUSTABLE
FEET
REAR ADJUSTABLE
FEET. (Refer to p.10).
Lens Shift Adjustment
The projection angle is adjustable up to 2.8 degrees 
upward and downward respectively by rotating front and 
back feet .
To raise the projector, rotate the feet clockwise.
To lower the projector or to retract the adjustable feet, 
rotate the feet counterclockwise.
To correct keystone distortion, press the KEYSTONE 
button on the remote control or select Keystone from the 
menu...

19
Terminals of Projector
The projector has two replaceable Interface board slots. The projector's functions can be extended by installing 
the optional interface boards into the terminal slots. 2 vacant slots (Input 3 and 4) are provided in your 
purchasing the projector.  For the Optional Interface Boards, contact sales dealer where you purchased the 
projector.
Pull out  the interface board.Remove 2 Screws from an interface board.
1
2
Tighten screws to secure the interface board.
Replace  the...

20
Installation
Connecting to Computer
VGA Cable 
Monitor Output 
Desktop type
Laptop type
Terminals of
the projector Monitor Output 
DVI Cable 
BNC Cable ✽
Monitor Output 
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
Cables used for connection 
• VGA Cable (D-sub 15 pin) *
• DVI Cable 
• BNC Cable (BNC x 5)    
 ( *One cable is supplied; Other cables are not supplied with this projector.)
G V
H/HV
R
B
DIGITAL ANALOG