Eiki Projector Lc W3 User Manual

							21
BASIC OPERATION
Press the POWER ON-OFF button on the top control or on
the remote control, and a message Power off? appears on
the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The LAMP Indicator lights bright and READY
Indicator turns off. After projector is turned off, Cooling Fans
operate (for 90 seconds). During this Cooling Down period,
this appliance cannot be turned on. 
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD  WHILE
COOLING FANS ARE RUNNING OR BEFORE READY
INDICATOR LIGHTS GREEN AGAIN.  OTHERWISE IT
WILL RESULT IN SHORTENING LAMP LIFE.
3When the projector has cooled down, READY Indicator lights
GREEN again and you can turn projector on. After cooling
down completely, disconnect AC Power Cord.
The message disappears after 4 seconds.
• The projector cannot be turned on during the cooling period with the
READY indicator turned off.  You can turn it on again after the READY
indicator GREEN again.
• When the On start function is on, this projector is turned on automati-
cally by connecting the AC power cord to an AC outlet.  (See page 40
for the On start function.) 
• Do not operate the projector continuously without rest.  Continuous use
may result in shortening the lamp life.  Turn off the projector and give it
a rest about an hour in every 24 hours.   
• This projector monitors internal temperature and automatically controls
the running speed of the cooling fans. 
• If the WARNING TEMP  indicator flashes red, see “WARNING TEMP
INDICATOR ” on page 44.
TURNING OFF THE  PROJECTOR
NOTE; 
						

							22
BASIC OPERATION
ADJUSTING SCREEN
Message disappears after 4 seconds.
Message disappears after 4 seconds.
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
1Press ZOOM button on Top Control or ZOOM ▲/▼button on
Remote Control Unit.  Message “Zoom” is displayed.
2Press ZOOM ▲button or POINT UP button to make image
larger, and press ZOOM ▼button or POINT DOWN button to
make image smaller.
1Press FOCUS button on Top Control or FOCUS ▲/▼button on
Remote Control Unit.  Message “Focus” is displayed.
2Adjust focus of image by pressing FOCUS ▲/▼button or
POINT UP/DOWN buttons.
LENS SHIFT ADJUSTMENT
1Press LENS SHIFT button on Top Control or LENS SHIFT ▲/▼
button on Remote Control Unit. Message “Lens shift” is
displayed.
2Press POINT UP button or LENS SHIFT ▲button to move
image up, press POINT DOWN or LENS SHIFT ▼button to
move image down.
KEYSTONE ADJUSTMENT
1Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu.  (Refer to page 38.)  Keystone
dialog box appears.
2Correct keystone distortion by pressing POINT
UP/DOWN/LEFT/RIGHT buttons.  Press POINT UP button to
reduce the upper part of the image, and press POINT DOWN
button to reduce the lower part.  Press POINT LEFT button to
reduce the left part, and press POINT RIGHT button to reduce
the right part.  
Reduce the upper width
with POINT UP button. Reduce the lower width
with POINT DOWN button.  
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Reduce the left part with
POINT LEFT button.  Reduce the right part with
POINT RIGHT button.  
•Arrows are white in no correction.
•Arrow(s) of direction being corrected turn(s) red.
•Arrow(s) disappear(s) at the maximum
correction.
•If you press the KEYSTONE button on Remote
Control Unit once more while the keystone
dialog box is being displayed, the keystone
adjustment will be canceled.
NOTE;
Focus adjustment may not function properly if the image is
corrected by KEYSTONE adjustment.
Message disappears after 4 seconds. 
						

							23
Press FREEZE button on Remote Control Unit to freeze picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button.
Press NO SHOW button on Remote Control Unit to black out image.
To restore to normal, press NO SHOW button again or press any
other button.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
Message disappears after 4 seconds.
1
2
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon. 
Volume
Press VOLUME (+/–) buttons on Top Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound.  To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) buttons.
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing. 
Press POINT UP/DOWN buttons to move a red frame pointer to
item that you want to select, and then press SELECT button.
SOUND ADJUSTMENT
DIRECT OPERATION
MENU OPERATION
Volume
Indicates roughly level of
volume.
Press MUTE button to set
Mute function On or Off.
Display disappears after 4 seconds.  
SOUND MENU
Press POINT LEFT/RIGHT buttons to cut off sound.  Dialog box
display is changed to “On” and sound is cut off.  To restore sound to
its previous level, press POINT LEFT/RIGHT buttons again.
Mute
BASIC OPERATION
Close SOUND MenuIndicates roughly
level of volume.SOUND Menu icon 
						

							24
SELECTING INPUT SOURCE
DIRECT OPERATION
Select INPUT source by pressing INPUT button on Top Control or on
Remote Control Unit.
Select INPUT source by pressing INPUT 1, INPUT 2 or INPUT 3
button on Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
INPUT button
Input 1
Input 2
Input 3
SELECTING COMPUTER SYSTEM
WHEN SELECT  INPUT 1 (COMPUTER INPUT TERMINALS )
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.
Press POINT UP/DOWN buttons to move a red arrow pointer to
Input 1 and then press SELECT button.  Source Select Menu will
appear.   
1
2
Input 1
INPUT MENU
Move a pointer to source that you want to select and then press
SELECT button.3
When your computer is connected to INPUT 1 (DIGITAL)
terminal, select RGB (PC digital).
RGB (AV HDCP)
When your computer is connected to INPUT 1 (ANALOG)
terminal, select RGB (PC analog).Move a pointer (red arrow)
to source and press
SELECT button.
Source Select Menu
INPUT Menu icon
Move a pointer (red arrow) to
Input 1 and press SELECT
button.
RGB (PC digital)
RGB (Scart)
When scart video equipment is connected to INPUT 1
(ANALOG) terminal, select RGB (Scart).
If a HDCP-compatible signal source is connected to the INPUT 1
(DIGITAL) terminal, select RGB (AV HDCP).
NOTE;
HDCP (High-bandwidth Digital Content
Protection) is a system for protecting digital
entertainment content which is delivered by DVI
(Digital Visual Interface) from being copied.
The specification of HDCP is decided and
controlled by Digital Content Protection, LLC.
Should the specification be changed, this
projector may not display the digital content
protected by HDCP.
RGB (PC analog)
COMPUTER INPUT
Input
NOTE;
INPUT SOURCE changes if the INPUT 1 button on Remote Control
Unit is pressed.
SVGA1
Input 1
Input 2
Input 3 
						

							25
COMPUTER INPUT
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA, SXGA+, WXGA
or UXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on pages 52-53).  When a computer is selected, this
projector automatically tunes to incoming signal and projects the proper image without any special setting.  (Some
computers need to be set manually.) 
The projector displays one of the Auto, -----, Mode 1/2/3/4/5/6/7/8/9/10, or the system provided in the projector.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon.
When image is not provided properly, manual adjustment
is required.  (Refer to P27 and 28.)
There is no signal input from computer.  Make sure
connection of computer and a projector is set correctly.  
(Refer to TROUBLESHOOTING on page 48.)
Auto
––––
PC SYSTEM Menu icon
Displays system being
selected.
PC SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.
Press POINT UP/DOWN buttons to move a red arrow pointer to
system that you want to set, and then press 
SELECT button.  
1
2
PC SYSTEM MENU
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
AUTOMATIC MULTI-SCAN SYSTEM
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.1
3
When connect a computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V
jacks.
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
Input 2
INPUT MENU
Move a pointer (red arrow)
to RGB and press SELECT
button.
Source Select Menu
Press POINT UP/DOWN buttons to move a red arrow pointer to
Input 2 and then press SELECT button.  Source Select Menu will
appear.   2
INPUT Menu icon
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
PC SYSTEM Menu icon 
Displays system being selected.
Systems on this dialog box can
be selected.
Custom Mode (1~10) set in PC
ADJUST Menu.  (P27, 28)
User preset adjustment in MANUAL PC ADJUSTMENT.
Adjustment data can be stored in the Mode 1-10.Mode 1
Computer systems provided in the projector. The
projector chooses proper system and displays it.SVGA 1
Mode 1 and SVGA 1 are examples.✽
Input
NOTE;
INPUT SOURCE changes if the INPUT 2 button on Remote Control
Unit is pressed.
SVGA1
Input 1
Input 2
Input 3
SystemMode 1
Mode 1
Mode 2
SVGA 1
SVGA 2
SVGA 3
SystemMode 1
Move a pointer (red arrow) to RGB and then press SELECT
button. 
						

							26
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer.  Auto PC Adjustment function can be operated as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT UP/DOWN buttons to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Top Control or on Remote Control
Unit.
PC ADJUST MENU
Auto PC Adj.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector.  Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P25).  Refer to
MANUAL PC ADJUSTMENT section (P27-28).
NOTE
●Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment
function.  When image is not provided properly through this function, manual adjustments are required.  (Refer to pages
27, 28.)
●Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “480p”, “575p”, “480i”, “575i”
“720p (HDTV)”, “1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.
PC ADJUST Menu icon
Move a red frame pointer to AUTO
PC Adj. icon and press SELECT
button.
Auto PC adj.SVGA1 
						

							27
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed.  However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector.  If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats.  This projector has 10 independent memory areas to memorize those parameters manually adjusted.  This
enables you to recall setting for a specific computer whenever you use it. 
Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal is selected on INPUT MENU
(P24).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT UP/DOWN buttons to move a red frame pointer to
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear.  Press POINT LEFT/RIGHT
buttons to adjust value.
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT buttons to adjust value. (From 0 to 31.)
Fine sync
Adjust the number of total dots in one horizontal period. Press
POINT LEFT/RIGHT buttons and adjust number to match your PC
image.
Total dots
Adjusts horizontal picture position.  Press POINT LEFT/RIGHT
buttons to adjust position.
Position H
Adjusts vertical picture position.  Press POINT LEFT/RIGHT
button(s) to adjust position.
Position V
Press SELECT button to show information of computer selected.
Current mode
Adjusts clamp position. When image has a dark bar(s), try this
adjustment.
Clamp
Press SELECT button at
Current mode icon to
show  information of
computer connected.
Current mode
PC ADJUST MENU
PC ADJUST Menu icon
Move a red frame pointer to item
and press SELECT button.
Press POINT LEFT/RIGHT
buttons to adjust value.
Press SELECT button at this icon to
adjust “Clamp,” “Display area H” or
set “Display area V.”
Press SELECT button at this icon
to display previous items.
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT buttons to decrease/increase value and then
press SELECT button.
Display area H
Adjustment of vertical area displayed with this projector.  Press
POINT LEFT/RIGHT buttons to decrease/increase value and then
press SELECT button.
Display area V
Selected Mode
Shows status
(Stored / Free) of
selected Mode.
Auto PC adj.
SVGA1
Fine sync
Mode 1 Stored 
						

							28
COMPUTER INPUT
Reset
Store
Closes PC ADJUST MENU.
Quit
Other icons operates as follows.
To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button.  Move a red arrow
pointer to any of Mode 1 to 10 that you want to store and then
press SELECT button.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Mode free
Vacant Mode
Shows values of “Total dots,”
“Position H,” “Position V,”
“Display area H,” and “Display
area V.”
Close this dialog box.
To store adjustment data.
To clear adjustment data.
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button.  Move
a red arrow pointer to Mode that you want to clear and then
press SELECT button.
This Mode has parameters being stored.
Close this dialog box.
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5Stored
Free
Free
Free
Free
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5Stored
Free
Free
Free
Free 
						

							29
COMPUTER INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE SELECT Menu icon.1
2Press POINT UP/DOWN buttons to move a red frame pointer to
level that you want to set and then press SELECT button.IMAGE SELECT MENU
Normal picture level preset on this projector.
Standard
Picture level with improved halftone for graphics.
Real
User preset picture adjustment in IMAGE ADJUST Menu (P37).
IMAGE 1~10
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1 to Image 10 by
pressing IMAGE button on Top Control or IMAGE SELECTION ▲/▼
button on  Remote Control Unit.IMAGE button
Standard
Real
Image 1
Image 10
Normal picture level preset on this projector.  
Picture level with improved halftone for graphics.
User preset picture adjustment in IMAGE ADJUST Menu (P37).
Standard
Real
IMAGE 1~10
Move a red frame pointer to level
and press SELECT button.IMAGE SELECT
Menu icon
Image 1SVGA 1 
						

							30
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SCREEN Menu icon.
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. zoom +” is displayed.  Press SELECT button to
expand image size.  And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image.  Panning function can work only when image
is larger than screen size.
A projected image can be also expanded by pressing D.ZOOM and
SELECT button on Remote Control Unit.  
1
To cancel Digital Zoom +/– mode, press any button except D.ZOOM,
SELECT and POINT buttons.
Press POINT UP/DOWN buttons and move a red frame pointer to
function that you want to select and then press SELECT button.2
Digital zoom +
NOTE
●Picture screen adjustment can not be operated
when “720p (HDTV)”, “1035i (HDTV)” or “1080i
(HDTV)” is selected on PC SYSTEM Menu  (P25).
●True and Digital zoom +/- can not be selected
when “480i”, “575i”, “480p” or “575p” is selected on
PC SYSTEM Menu  (P25).
●This projector cannot display any resolution higher
than 1600 X 1200.  If your computer’s screen
resolution is higher than 1600 X 1200, reset
resolution to lower before connecting projector.
●Image data in other than XGA (1024 x 768) is
modified to fit screen size in initial mode.
●Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
NormalSCREEN MENU
When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. zoom –” is displayed.  Press SELECT button to
compress image size. 
A projected image can be also compressed by pressing D.ZOOM
and SELECT button on Remote Control Unit.  
Digital zoom –
Move a red frame pointer to function
and press SELECT button.SCREEN Menu icon
True
Provides image to fit the panel size of the screen.
Full
Provides image to fit the horizontal size of the screen.
Provides image in its original size. When the original image size is
larger than screen size (1366 X 768), this projector enters “D. Zoom
+” mode automatically.
COMPUTER INPUT
PICTURE SCREEN SELECT (DIRECT)
Select picture screen among Normal, Full and True by pressing
SCREEN button on Remote Control Unit.SCREEN button
Normal
Full
True
PICTURE SCREEN SELECT (MENU)