Eiki Projector Lc Uxt3 User Manual

41
This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain Lamp-life.  (This projector is
shipped with this function ON.)
Power Management function operates to turn Projection Lamp off
when input signal is interrupted and any button is not pressed over 5
minutes.  This function operates as follows;
1. When any input signal is interrupted, “No signal” and counting
down display appears...

42
Lamp counter reset
Move pointer to Lamp counter reset and then
press SELECT button.  
Move arrow to
replaced lamp number (Lamp 1, Lamp
2, Lamp 3 or Lamp 4) and then press
SELECT button.
USB
Projector mode
Select   when controlling a projector with computer.
NOTE:Before you control a projector by computer, install USB driver
(optionally sold parts) and set up computer following instruc-
tion in USB driver package. Contact your authorized dealer.
This Projector is equipped with USB port for interactive...

43
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most
Personal Computers.  POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.  When ON-
SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function cannot be...

44
APPENDIX
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch lens.
When a projector is not in use, replace lens cap.
1
3
Lightly wipe cleaning cloth over lens.2
Follow these steps to clean projection lens:
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from AC outlet.1
2
Air Filter prevents dust from accumulating on...

45
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function.  Lamp Management Function detects status of all lamps and shows status on screen or on LAMP
REPLACE indicator.  This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions. 
Projection Lamp lights normally.
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection...

46
APPENDIX
Check number of lamp to be replaced on Lamp Status Display.
Remove two screws on Lamp Cover and press button to open
Lamp Cover.  (See right figure.)
1
3
Loosen two screws and pull out Lamp Assembly to be replaced
by grasping handle.4
Turn off a projector and disconnect AC Power Cord.  Allow a
projector to cool down for at least 45 minutes.2
Replace Lamp Assembly with a new one and tighten two screws.
Make sure Lamp is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp...

47
APPENDIX
This projector uses a high-pressure lamp which must be handled carefully and properly.  Improper
handling may result in accidents, injury, or create a fire hazard.
Lamp lifetime may differ from lamp to lamp and according to the environment of use.  There is no
guarantee of the same lifetime for each lamp.  Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if the LAMP...

48
Check audio cable connection from audio input source.
Adjust audio source.
Press VOLUME (+) button.
Press MUTE button.
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING
PROJECTOR  on pages 12 ~ 15.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is...

49
Check cable connection between a projector and your computer.
Check mouse setting on your computer.
Turn a projector on before turning on a computer.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Remote Control Unit
does not work.Check batteries.
Check...

Owner’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable and DVI Cable
MAC/VGA Adapter and DVI/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port) 
6 Types Light-Block Sheet (For option lens)
Lens Mounting Parts
Protective Dust Cover
50
Accessories
TECHNICAL SPECIFICATIONS
1.8 TFT Active Matrix type, 3 panels
Multi-media Projector
81.7 lbs (37 kg)
22.9 x 10 x 30.9 (581 mm x 252 mm x 783 mm) 
1024 x 768 dots
2,359,296 (1024 x 768 x 3...