Eiki Projector Lc Sx6a User Manual

							41
Computer Adjustment
Press the MENU button to display On-Screen Menu. Spin
Menu icons with the Point buttons (7and 8) or the Control
pad and press the SELECT button when the PC ADJ. icon
comes right in front.1
2
Move the yellow
frame pointer to an
item and press the
SELECT button.
PC Adjust Menu
Adjust value with the Point
buttons (eand d) or
the Control pad.
Some computers employ special signal formats which may not be
tuned by Multi-scan system of this projector. Manual PC
Adjustment enables you to precisely adjust several parameters to
match those signal formats. The projector has 50 independent
memory areas to memorize those parameters adjusted manually.
It allows you to recall the setting for a specific computer easily. 
Eliminates flicker from the image displayed. Adjust value with the
Point buttons (
eand d) or the Control pad.
(From 0 to 31)
Fine sync
Adjusts the number of total dots in one horizontal period.  Adjust
number to match your PC image with the Point buttons (
eand
d) or the Control pad.
Total dots
Press the SELECT button to show H-Freq. and V-Freq. of the
connected computer. 
Current mode
Adjusts clamp level (Phase and Width). When the image has dark
bars, try this adjustment.
Clamp
Adjusts the resolution at the Display area dialog box.
Horizontal
Adjusts the horizontal area displayed by this projector.
Decrease or increase value with the Point buttons (
eand d)
or the Control pad.
Vertical
Adjusts the vertical area displayed by this projector.  Decrease
or increase value with the Point buttons (
eand d) or the
Control pad.
Display areaPress the SELECT button at
the Current mode to show
the information of the
connected computer.
Current mode
Manual PC Adjust
Move the yellow frame pointer with the Point buttons (e
and d) or the Control pad to an item which you want to
select.
Press the SELECT button to access an adjustment dialog
box. Adjust value with the Point buttons (
eand d) or the
Control pad.3
Computer Adjustment 
						

							42
Adjust this item when the projected image is affected by the
noise from the external equipment. (From 0 to 15) 
V-sync phase
Reset
Mode
Exits the PC Adjust Menu.
Quit
Resets all adjustments to their previous levels.
Vacant Mode
shows the selected input,
source and system, and  values
of “Fine sync,” “Total dots,”
“Clamp,” “Display area,” and
“Position.”
To store adjustment data
To clear adjustment data
Press the SELECT button
at the Display area and the
Display area dialog box
appears.
✔Note:
Fine sync. and Display area cannot be selected when 480i, 575i, 480p, 575p, 720p,
1035i, 1080i/50, or 1080i/60 is selected in the System menu. (p39)
Adjusts picture position.
Position
Computer Adjustment
To store the adjustment data or clear the stored data, move the
yellow frame pointer to Mode and then press the SELECT
button. 
Store
To store the adjustment data, select Store and press the
SELECT button to display Mode dialog box. Move the yellow
frame pointer to any of Mode 1 to 50 in which you want to
store and then press the SELECT button.
Free
To clear the adjustment data previously set, select Free and
press the SELECT button to display Mode dialog box. Move
the yellow frame pointer to any of Mode 1 to 50 in which you
want to clear and then press the SELECT button.
✔Note:V-sync phase is not displayed as the item is initially checked off on My menu in the
Setting menu. Change the My menu setting in the Setting menu (p49) when
necessary to adjust V-sync. phase.  
						

							43
Image Adjustment
Image Adjustment
Image Menu (PC)
Move the  yellow
frame pointer to
an image level you
want to select and
then press the
SELECT button.
1
Normal picture level preset on this projector for AV mode.
Standard 
Picture level with improved halftone for graphics.
Real
Normal picture level preset on this projector for PC mode.
Standard 
Picture level adjusted for picture with fine tone.
Cinema
User preset picture adjustment in IMAGE ADJ. menu (p44~ 46).
IMAGE 1~10
2
selects image level from Standard, Cinema, Real, and Image 1~10.
Press the MENU button to display On-Screen Menu. Spin
Menu icons with the Point buttons (
7and 8) or the Control
pad and press the SELECT button when the IMAGE icon
comes right in front.
Move the yellow frame pointer with the Point buttons (e
and d) or the Control pad to an image level which you want
to select and then press the SELECT button.  
Image Menu (AV)
For PC Input
For AV Input
User preset picture adjustment in IMAGE ADJ. menu (p44~46).
IMAGE 1~10
✔Note:Image 1~10 are common for PC and AV sources, which means 10 memory areas are
prepared for PC and AV sources totally.
Image
IMAGE icon
Indicates the other
items exists below. 
						

							1
2
Decrease or increase contrast with the Point buttons (eand d)
or the Control pad. (From 0 to 63.)
Adjust image darker or brighter with the Point buttons (eand d)
or the Control pad. (From 0 to 63.) Contrast
Brightness
Lighten or deeper color with the Point buttons (eand d) or the
Control pad. (From 0 to 63.)
Adjust with the Point buttons (eand d) or the Control pad to
obtain proper color. (From 0 to 63.) Color
Tint
Image Adjust 
Image Adjust Menu
Color management
The Color management function enables you to adjust color
level, phase and gamma of the selected spot of the projected
image and exchange the original color with the adjusted one.
The projector can store up to eight color management data.
adjusts Contrast, Brightness, Color, Tint, Color management, Auto picture
control, Color temp., Red, Green, Blue, Sharpness, Gamma, Noise reduction,
Progressive, and Film; selects Reset and Store.
Pointer (yellow frame)
Move the yellow frame
pointer with the Point
buttons 
(eand d)or
the Control pad to an
item which you want to
adjust.
Indicates the other
items exists below.
Item dataAdjust value with the
Point buttons (eandd) or the Control pad.
44
Press the MENU button to display On-Screen Menu. Spin
Menu icons with the Point buttons (
7and 8) or the Control
pad and press the SELECT button when the IMAGE ADJ.
icon comes right in front.
Move the yellow frame pointer with the Point buttons (e
and d) or the Control pad to an item which you want to
adjust.
Press the SELECT button to display an adjustment dialog
box. Adjust value with the Point buttons (
eand d) or the
Control pad.3
IMAGE ADJ. icon
✔Note:•Color and Tint cannot be displayed when PC input source is selected.
• Tint cannot be adjusted when the video system is PAL, SECAM, PAL-M, or PAL-N.
(p39) 
Color selection Press the SELECT button when Color management is
highlighted and then Color management pointer will appear.
Move the pointer to a spot which you want to adjust the color
of with the Point buttons (
e, d, 7, and 8) or the Control pad,
and press the SELECT button.  The image being projected
freezes and Color Selection window will appear.
X-axis of COLOR pallet shows Phase and Y-axis, Level.
Select a level and phase which you prefer with the Point
buttons (
e, d, 7, and 8) or the Control pad and press the
SELECT button to move the pointer to GAMMA.
Select a position of GAMMA which you prefer with the Point
buttons (
eand d) or the Control pad and press the SELECT
button.
While adjusting COLOR and GAMMA, the projected image
color will change accordingly.
Color management pointer Move the pointer to a spot which you
want to adjust the color of and then
press the SELECT button. Color
Selection window will appear as
shown below.
Color selection 
Pointer (red frame)
Image Adjustment 
						

							45
Image Adjustment
Image Adjustment
Move the pointer to one of the followings with the Point
buttons (
e, d, 7, and 8) or the Control pad and press the
SELECT button.
LIST.............displays Color Management List window to store
the adjustment data.
COLOR.M..returns to the previous image with the Color
management pointer.
MENU.........displays a confirmation dialog box. Select [Yes] to
return to the menu display.
Color management list
After selecting LIST on the Color selection window, Color
Management List will appear. Move the pointer to one of the
followings with the Point buttons (
e, d, 7,and 8) or the
Control pad and press the SELECT button.
ALL DEL......deletes all the data on the list.
MENU.........displays a confirmation dialog box. Select [Yes] to
return to the menu display.
COLOR M...returns to the previous image with the Color
management pointer.
Press the CANCEL button to exit the Color management mode.
Move the pointer
to the selected
color and press the
SELECT button.
The confirmation
dialog box appears.  
Color management list
Clear the check mark with the
SELECT button not to apply
the adjusted color to the
projected image.
Soften or sharpen the image with the Point buttons (eand d)or
the Control pad. (From 0 to 15.)
Sharpness
Lighten or deepen green tone of the picture with the Point
buttons (
eand d) or the Control pad. (From 0 to 63.)
Green
Lighten or deepen blue tone of the picture with the Point buttons
(
eand d) or the Control pad. (From 0 to 63.)
Blue Auto picture control
With this function enabled, the projected image will be easier to
see by emphasizing black of the picture. Select one from the
following settings:
Off ······disabled
L1 ······ emphasizes black of the picture.
L2 ·······emphasizes black of the picture greater than L1.
Lighten or deepen red tone of the picture with the Point buttons
(
eand d) or the Control pad. (From 0 to 63.)
Red Color temp.
Select a level from among XLow, Low, Mid and High with the
Point  buttons (
eand d) or the Control pad and the SELECT
button. 
Select [Yes] to
return to the
menu display.
The setting selected.
The setting selected.
✔Note:If either value of Red, Green, and Blue is adjusted, “Adj.” will be selected in Color
temp. automatically.   
						

							Reset all adjustments to their previous figures.
Exits Image Adjust menu.
To store the adjustment data, move an yellow frame pointer to
Store and press the SELECT button. Image Level Menu will
appear. Move the yellow frame pointer to one of Image 1~10
and   then press the SELECT button. 
With this function “On”, interlaced video signal is displayed in a
progressive picture. Progressive 
This function is effective on 2:3 or 2:2 pulldown video sources.
With this function “On”, the projector reproduces pictures
faithful to the original film quality.
Film
✔Note:
•  Progressive, Film, and Noise reduction cannot be displayed when selecting PC input
source.
• Progressive cannot be selected when 480p, 575p, and 720p is selected in the
System menu. (p39)
• Film can only be activated when selecting PAL, NTSC, 480i, or 575i for Video
System and “On” for Progressive. 
• 2:3 Pulldown or Telecine transfer is the process of changing images from film mode
to video mode. While film runs at 24 frames per second (fps), NTSC television
signals (or video) have a run rate of 30fps so the 24 fps film needs to be speeded
up to 30fps and transferred using a proper field pattern to get the best film-like
images. 2:2 Pulldown uses the same process of changing images as 2:3 pulldown,
but the difference is that 24 fps film is speeded up for PAL television signal (or
video) having 25 fps.
Store 
Image Level MenuMove the yellow frame pointer to
an image and then press the
SELECT button.The confirmation
box appears.
Select [Yes] to store the image
adjusted.
Select one of the followings to reduce noise of the  image.
Off  . . . .disabled
L1  . . . . .Select “L1” for an active picture.
L2  . . . . .Select “L2” for a still picture.
Noise reduction
46
Image Adjustment
Adjust with the Point buttons (eand d) or the Control pad to
obtain better balance of contrast. (From 0 to 15.)
Gamma
Store
Reset
Quit 
						

							47
Screen Setting
Provides image to fit the horizontal size of the screen size.
When the input signal is SXGA (5:4), the image is fully displayed
at 4:3 aspect ratio. Full screen
Adjusts aspect (scale and position) of the screen. Press the
SELECT button at Custom. Custom will be displayed on the top
left of the screen for four (4) seconds and then return to the
previous menu display. Press the SELECT button again with the
pointer stayed on Custom to display Aspect setting menu. Adjust
each value of Scale and Position.
Scale  . . . . .adjusts horizontal and vertical scale of the screen.
(From –32 to +32)
H&V  . . . . .changes Vertical value subject to Horizontal value;
when a checkmark is put on H&V, Scale V cannot
be adjusted.  
Position  .  .adjusts horizontal and vertical position of the
screen. (From –15 to +15)
Common  . .applies the current Aspect setting to all the Inputs.
Reset  . . . . .resets all adjusted values to zero. 
Quit  . . . . . .exits the Aspect setting menu.
1
2
Screen Setting Menu
Wide
Provides image to fit screen size.
Normal
True
Custom (Aspect)
Provides image in its original size. When the original image size is
larger than the screen size, this projector enters panning mode
automatically. While “True” is displayed on screen, pan the
image with the Point buttons (
e, d, 7, and 8) or the Control
pad. Digital zoom + and – mode can be switched by pressing the
SELECT button.
Provides image to fit wide video aspect ratio (16:9) by expanding
image width uniformly. This function can be used for providing a
squeezed video signal at 16:9.
selects the screen size from Normal, Wide, True, and Full screen;
customizes it by Scale, H&V, Position, Common, and Reset; adjusts it by
Digital zoom +/–, Keystone; sets Ceiling and Rear. 
Screen
Press the MENU button to display On-Screen Menu. Spin
Menu icons with the Point buttons (
7and 8) or the Control
pad and press the SELECT button when the SCREEN
SETTING icon comes right in front.
Move the yellow frame pointer with the Point buttons (e
and d) or the Control pad to an item which you want to
select.
Screen (Custom: H&V)
Screen Setting
Screen (Custom)
Item dataAdjust value with
the Point buttons
(eand d)or the
Control pad.
Screen (Custom: Common)
Screen Setting
icon
Aspect Setting MenuMove the pointer to an item to set and
adjust value with the Point buttons (eand d)or the Control pad.
Pointer
Checkmark
Move the pointer to Common and press
the SELECT button. The confirmation
box appears. Select [Yes] to activate it.
Pointer
✔Note:
The adjusted aspect can basically be memorized for each input even if the projector
is turned off.
Screen Setting 
						

							48
Press the SELECT button at the D. Zoom –. The message “D.
Zoom –” is displayed. Press the SELECT button to compress the
image size.  D. Zoom –
Ceiling 
Rear 
When this function is “On,” the picture is top/bottom and left/right
reversed. This function is used to project the image from a ceiling
mounting the  projector.
When this function is “On,” the picture is left/right reversed. This
function is used to project the image to a rear projection screen.
Press the SELECT button at the D. Zoom +.  The message “D.
Zoom +” is displayed. Press the SELECT button to expand the
image size. And use the Point buttons (
e, d, 7, and 8) or the
Control pad to pan the image. The Panning function can work
only when the image is larger than the screen size.
D. Zoom +
Ceiling
Rear
D. ZoomD. Zoom
This function corrects distortion of a projected image. Press the
SELECT button at Keystone and the keystone dialog box appears.
Adjust keystone with the Point buttons (
e, d, 7, and 8) or the
Control pad. 
Press the Point 
8button or the Control pad at Keystone and
select either Store or Reset with the Point buttons (
eand d) or
the Control pad, and then press the SELECT button to fix the
selection. 
Store  . . . .stores the keystone adjustment even if the AC
power cord is disconnected.
Reset  . . . . .resets the keystone adjustment when the AC power
cord is disconnected.
Keystone
Keystone
✔Note:To exit the D. Zoom +/– mode, try the followings:
•To return to the normal screen, change Input, or change the screen size.
•To exit the panning mode, press any button except the D. ZOOM button, the
SELECT button, and the CH and ID buttons.
Screen Setting
✔Note:• The True and D. Zoom +/– cannot be selected when projecting AV sources or
selecting “480i”, “575i”, “480p”, or “575p” in the System menu  (p38~39).
• This projector cannot display any resolution higher than 1600 X 1200.  If your
computer’s screen resolution is higher than 1600 X 1200, reset the resolution to
the lower before connecting the source to the projector.
•The image data in other than XGA (1024 x 768 for LC-X6A) or SXGA (1400 x
1050 for LC-SX6A) is modified to fit the screen size in initial mode.
•The panning function may not operate properly if the computer system prepared in
the PC Adjust Menu is used. 
						

							49
Menu
1
2
Setting
Language
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean, or Japanese.
This feature allows you to change the On-Screen Menu setting.
Position
When Position is selected, arrows appear in upward, downward,
right and left directions on the screen.  Move the menu position
with the Point buttons (e, d, 7, and 8) or the Control pad and
fix it by pressing the SELECT button.
My menu
This feature enables you to customize the On-Screen menu
display.  Put checkmarks on items of each menu that you want
to display. 
Simple menu
On  . . . . . . .When adjusting value in the Image adjust menu, the
value adjustment bar is displayed on the bottom left
of the screen.
Off  . . . . . . .Default setting.
Setting Menu (Language)
changes various settings: Language, Menu, Logo, Background, Lamp,
Remote control, Display, Input search, Power management, On start, Analog
out, Lens memory, Shutter, Security, and Factory default. 
Press the MENU button to display On-Screen Menu. Spin
Menu icons with the Point buttons (
7and 8) or the Control
pad and press the SELECT button when the SETTING icon
comes right in front.
Move the yellow frame pointer with the Point buttons (e
and d) or the Control pad to an item which you want to set
and then press the SELECT button. The Setting dialog box
appears.
Menu Position
Setting icon
Language Menu
✔Note:•Input and Menu items cannot be hid with the My menu setting.
• When selecting Default on My menu setting, all items of the On-Screen Menu will
be displayed.
My Menu
CheckmarkMove the pointer to an item to be
displayed and put a checkmark on
the item by pressing the SELECT
button.
Pointer
Setting
Setting  
						

							50
Setting
Logo
Logo settings can be altered as follows:
Logo select
This function decides what to be displayed on the starting-up
display as follows:
Default  . . . .the factory-set logo
My logo  . . .the image you captured  
Off  . . . . . . .count-down only 
Capture
This function enables you to capture the image being projected
and use it for a starting-up display or interval of presentations.  
After capturing the projected image, go to the Logo function and
set it to “My logo”. Then the captured image can be displayed
when turning on the projector next time. (p27) 
To capture the image, select [Yes]. To cancel the Capture
function, select [No].  
✔Note:
• Before capturing an image, select Standard in the Image Menu to capture a proper
image. (See page 43.)
• Certain signals may not be captured properly.
• When capturing the image that has been adjusted by the Keystone function, the
adjustment data is automatically reset and the projector captures an image without
keystone correction. 
• Once you exit the Logo menu after setting Logo lock to “On”, you are required to
enter the PIN code every attempting to change the Logo setting.
Logo Lock SettingLock
This function prevents an unauthorized person from changing the
Logo setting.
Off  . . . . .the Logo setting can be changed freely from the
Logo menu.  
On . . . . . .the Logo setting cannot be changed without PIN
code.
If you want to change the Logo Lock setting, enter a PIN code
along the following steps. The initial PIN code for Logo Lock
setting is set “4321” at the factory.
Select [Yes]
to capture the
projected
image. 
Select [Yes] to
stop capturing.  
Capture
Logo Select
Enter a Logo PIN code 
Select a number with the Point buttons (e, d, 7, and 8) or the
Control pad and fix the number with the SELECT button. The
number will change to “
✳”. If you fixed a wrong number, move
the pointer to “C” with the Point buttons (
e, d, 7, and 8) or
the Control pad, then enter the correct number.
Repeat this step to complete entering a four-digit number. 
When the four-digit number is fixed, move the pointer to “Ent”.
Press the SELECT button so that you can change the Logo
Lock setting.
If you entered a wrong Logo PIN code, “Logo PIN code” and
the number (
✳✳✳✳) will turn red and disappear. Enter a Logo
PIN code all over again.
Enter a Logo PIN code
The input numbers
change to “✳” for
security.