Eiki Projector Lc Sx6a User Manual

21
Installation
Terminals for connecting the AC power cord and other equipment
are located in the front part of the projector for easy setup. The
terminal area is covered with a front cover to protect from dust
and others, and hide messy cable connections.  
The projectors front terminal area has two replaceable Interface
board slots. The projectors functions can be extended by installing
the optional interface boards into the terminal slots. Two vacant
slots (Input 4 and Input 5) are provid in your...

22
Installation
Connecting to Computer (Digital and Analog RGB)
Cables used for connection
qVGA Cable (HDB 15 pin) Only one cable is supplied.
wDVI-D Cable ✽
eBNC Cable ✽
rSerial Cross Cable (RS-232C) ✽
(✽ = Not supplied with this projector.)
q
Monitor Output
DIGITAL (DVI-D)
q
Monitor Input
SERIAL PORT IN
Note:Unplug the power cords of both the projector and external equipment
from the AC outlet before connecting the cables.
w✽
Monitor Output
ANALOG OUTANALOG IN
SERIAL PORT OUT
R    G       B    H/V...

23
Installation
Installation
Connecting to Video Equipment (Digital and Video)
INPUT 3VIDEO/Y   Cb/Pb     Cr/PrS-VIDEO
Cables used for connection
qVideo Cable ✽
wS-Video Cable ✽
eDVI-D Cable ✽
(✽ = Not supplied with this projector.)
Note:Unplug the power cords of both the projector and external equipment
from the AC outlet before connecting the cables.
VIDEO
w✽q✽
S-Video Output
e✽
DIGITAL (DVI-D)
Digital Output
(HDCP compatible)Video Output
S–VIDEO 

24
Connecting to Video Equipment (Component and RGB Scart)
INPUT 3VIDEO/Y   Cb/Pb     Cr/Pr
Cables used for connection
qBNC Cable✽ 
wScart-VGA Cable✽ 
eComponent Cable✽
(✽ = Not supplied with this projector.)
Note:
Unplug the power cords of both the projector and external equipment
from the AC outlet before connecting the cables.
RGB Scart
21-pin Output
w✽ q✽ 
Component Video Output
(Y, Pb/Cb, Pr/Cr) Component 
Video Output
(Y, Pb/Cb, Pr/Cr)
ANALOG INY    Cb/Pb   Cr/PrY   Cb/Pb  Cr/Pr
e✽
Installation 

25
Basic Operation
Basic Operation
Operating the Projector
You can operate the projector with the projectors top control, the remote control or a USB mouse (not provided). he remote
control can be used wireless or wired.
Operational range of the wireless remote control is within about 32.8 (10m) from the projector. Operational range differs
depending on environments where the projector is used. Any obstruction to air signal between the projector and the remote
control may prevent the remote control from...

Operations & Buttons
Ref. Pages
On-Off27, 28
Lens Shift➔ Point buttons➔29
Zoom➔ Point buttons  ( ed)   29
Focus➔ Point buttons  ( ed)     29
Shutter29, 53
Auto PC Adjust30, 40
Input Selection (Input 1–5) 30, 36~37
Information30, 59
Keystone –➔31, 48
Screen Selection–31, 47
Freeze–31
P-Timer–31
D. Zoom–➔32, 48
Remote CH and ID–16, 17
Menu33~35
Select + Point buttons➔ 
Cancel
Pad
Pad
Pad
Pad
26
Basic Operation
Basic Operation and Reference Buttons
For detail operations other than those on this page, follow...

27
Basic Operation
Basic Operation
Turn on the MAIN On/Off switch of the projector. The LAMP
indicator lights red, and the READY indicator lights green.
Press the POWER ON-OFF button on the top control or the
remote control. The LAMP indicator dims, and the cooling
fans start to operate. The preparation display appears on the
screen and count-down starts. The input and source
selected last appears after 20 seconds count-down.
2
3
1Complete peripheral connections (with Computer, VCR, etc.)
before turning...

28
Press the POWER ON-OFF button on the top control or the
remote control, and a message “Power off?” appears on the
screen.  1
2
3
Press the POWER ON-OFF button again to turn off the
projector. The LAMP indicator brightly lights red and the
READY indicator goes out. After approximately 90 seconds,
the READY indicator will light green again and then the
projector can be turned on by pressing the POWER ON-OFF
button.
The Cooling fans operate for approximately 2 minutes after
the projector is turned off;...

29
Basic Operation
Basic Operation
Press the ZOOM/FOCUS button and adjust with the Point buttons
(
eand d).
Press the LENS SHIFT button and adjust the lens position with the
Point buttons (
e, d, 7, and 8) or with the Control pad.
Shutter Function
Shutter function allows you to completely block out light to the
screen. Press the SHUTTER button to close the shutter inside the
projector. To open up the shutter, press the SHUTTER button
again. Refer to pages 53~54 for detail of setting for the Shutter...

30
Basic Operation
Information
Choose either Input 1, Input 2, Input 3, Input 4, or Input 5 by
pressing the INPUT button on the top control or the INPUT 1,
INPUT 2, INPUT 3, INPUT 4, or INPUT 5 buttons on the remote
control.
Before using these buttons, correct input source should be
selected through menu operation as described on pages 36~37.
Input 1
Input 3
Input 2
INPUT button
Input 5
Input 4
Auto PC Adjustment function is provided to automatically adjust
Fine sync, Total dots, Horizontal, and Vertical...