Eiki Projector Lc Sx6 User Manual

							11
Preparation
Top Control
LENS
SHIFTMENU
CANCEL
SELECTZOOM
FOCUSSHUTTERINPUT
INFO.  AUTO
PC ADJ.POWER P
qwerty
oi
u
uINPUT button
Switches input sources.  (p31)
yAUTO PC ADJ. button
Operates the Auto PC adjustment function.  (p31)
eCANCEL button
Cancels the selection and returns to the previous menu.  
t
INFO. button
Displays Information.  (p31) 
wMENU button
Opens or closes the On-Screen Menu.  (p34, 35 )
oPOWER ON-OFF button
Turns the projector on or off. (p28, 29)
iSHUTTER button
Closes and opens up the built-in shutter.  (p30)rControl pad 
Navigates through the menu or adjusts value in the On-
Screen Menu.  These are also used to pan the image in
the Digital zoom + mode.  (p33, 34, 35)
qLENS SHIFT button 
Activates Lens shift function.  (p30)
!0!1!2
!0SELECT button
Executes the item selected.  It is also used to expand/
compress the image in Digital zoom +/–  mode. (p33, 34,
35)
!1FOCUS button
Adjusts focus of the image. (p30)
!2ZOOM button
Adjusts zoom of the image. (p30)
About Control Pad
The built-in Control Pad is a
semiconductive touchpad operational
with light finger touch.  Glide your finger
up, down, right and left on the pad to go
to the desired menu, adjust values and
operate various convenient features.
Refer to the following pages for
respective directions. 
Preparation 
						

							12
Preparation
  ANALOG OUTINPUT 3
INPUT 1
INPUT 2  ANALOG IN
DIGITAL (DVI-D)
AUDIO 1
AUDIO 2
VIDEO/Y    Cb/Pb          Cr/PrG                B               R            H/V               V
VIDEO/Y   Cb/Pb     Cr/PrS-VIDEO R-AUDIO-L
(MONO)
Te r minals
q
w
e
r
eINPUT 3 terminals
AUDIO (R-L)
Connect the audio output from video equipment
connected to VIDEO/Y Cb/Pb Cr/Pr jacks or S-VIDEO
jack to these jacks.  (When the audio output is
monaural, connect it to L(MONO) jack.  (p24, 25)
VIDEO/Y, Cb/Pb, and Cr/Pr
Connect video or component output (Y, Cb/Pb and
Cr/Pr) from video equipment to these jacks with a
video cable (RCA-type).  (p24, 25)
S-VIDEO
Connect S-Video output from video equipment to this
jack.  (p24)
rINPUT 2 terminals
AUDIO 2
Connect the audio output from video equipment
connected to VIDEO/Y, Cb/Pb, and Cr/Pr jacks or G,
B, R, H/V, and V jacks to this jack.  (p22, 25)
VIDEO/Y, Cb/Pb, and Cr/Pr 
Connect video or component output (Y, Cb/Pb and
Cr/Pr) from video equipment to these jacks with a
video cable (BNC-type).  (p25)
G, B, R, H/V, and V
Connect RGB output signal from a computer with a
computer cable (5 BNC-type) to these jacks.  (p22)
wANALOG OUT
This terminal can be used for analog signal output
incoming through the ANALOG IN terminal (INPUT 1).
Connect this terminal to the other monitor with a VGA
cable.  (p22)
qINPUT 1 terminals
AUDIO 1
Connect the audio output from a computer or video
equipment connected to DIGITAL (DVI-D) or ANALOG
IN terminal to this jack.  (p22, 24)
DIGITAL (DVI-D)  (HDCP compatible)
Connect digital output signal from a computer or
video equipment to this terminal with a DVI-D cable.
(p22, 24)
ANALOG IN
Connect analog output signal from a computer or a
video equipment (Component or RGB Scart) to this
terminal with a VGA cable, a Scart-VGA or a
Component-VGA cable.  (p22) 
						

							13
Preparation
A built-in micro processor which controls this unit may occasionally
malfunction and need to be reset. This can be done by pressing the RESET 
button with a pen, which will shut down and restart the unit.  Do not use the
RESET function excessively.
q
ertyu
uSERIAL PORT IN
When controling the projector from a computer, connect
the computer to this terminal with a serial cross cable
(commercially supplied).
tUSB (Series B)
This port is used for the projector maintenance.
ySERIAL PORT OUT
This terminal outputs signal from SERIAL PORT IN.
When controling more than two projectors from a
computer, connect the other projector to this terminal
with a serial cross cable (commercially supplied). 
eR/C JACK
Connect the remote control to this jack with the supplied
remote control cable to use the remote control as wired.
(p26)
✽
✽
qINPUT 4 (WARP & BLENDING board)
DIGITAL (DVI-D) (HDCP compatible)
Connect digital output signal from a computer or
video equipment to this terminal with a DVI-D cable.
(p23)
SERIAL PORT IN
When operating Warp and Blending feature, connect
serial port of the computer and this terminal with a
serial cross cable (commercially supplied).  (p23)
SERIAL PORT OUT
When using Warp and Blending feature for more than
two projectors from a computer connected to the
SERIAL PORT IN terminal above, connect SERIAL
PORT IN terminal on the other projector and this
terminal with a serial cross cable (commercially
supplied).  (p23)
rUSB 
Connect a USB mouse (commercially available) to
control On-Screen Menu.
(p26)
Preparation
✔Note:
Refer to the enclosed operation manual for Warp and Blending in Advanced
Screen Manager.
w
wINPUT 5 (Vacant for Optional Interface Board)
Optional interface board can be installed into this slot.
This input accepts digital signals only.  (p21, 75) 
						

							14
Preparation
Remote Control 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
KEYSTONE
SHUTTER D.ZOOM
ZOOMFOCUS ON-OFF
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTE
VOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
q
w
u
i
e
r
y
!0
o
oZOOM buttons
Adjust zoom of the image. (p30)
rCONTROL PAD (semiconductive touchpad)
Selects an item or adjusts value in the On-Screen Menu.
This is also used to pan the image in the Digital zoom +
mode.  (p33)
w
KEYSTONE button
Corrects keystone distortion. (p32)uPOWER ON-OFF button 
Turns the projector on or off. (p28, 29)
e
LENS SHIFT button
Activates LENS SHIFT function. (p30)
iFOCUS buttons
Adjust focus of the image. (p30)
tWIRED REMOTE JACK
Connect the Remote Control Cable to this jack.
Battery installation is required regardless if it is used as
wired or wireless.  (p16, 26)!0SELECT button
Executes the item selected. 
t
yD.ZOOM button
Activates D.Zoom +/– function. (p33)qSHUTTER button
Closes the built-in shutter for light blocking.  (p30) 
						

							15
Preparation
!1SCREEN button
Selects screen sizes.  (p32)
!2
INPUT 1-3 buttons
Selects input source (INPUT 1 - INPUT 3).  (p31)
!0AUTO PC button
Operates the Auto PC adjustment.  (p31)
qMENU button
Opens or closes the On-Screen Menu.  (p34, 35)
wFREEZE button
Freezes the projected picture.  (p32)
!4REMOTE RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.”
Set it to “ALL OFF” for power saving when it is not
used.  Slide this switch to RESET with holding down
the CH and ID buttons at the same time to initialize the
Remote Control ID and CH.  (p16)
u
P-TIMER button
Operates P-Timer function.  (p32) 
MENU
CANCEL
INFOINFOAUTO PC
SCREENSCREENFREEZEFREEZE
P-TIMERP-TIMERSOUNDSOUND
REMOTEREMOTE
VOL.
MUTE
CH
ID
INPUT 4INPUT 1 
INPUT 2
INPUT 3 INPUT 5
REMOTE   RESET  ON   ALL OFF
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
q
e
!0
!1
t
y
o
!3
i
r
u!4
w
!2
eVOL. button
Adjusts volume.  (p33)
rMUTE button
Mutes sound.  (p33)
tCH button
Switches Remote Control Channel (CH).  (p16)
yID button
Switches Remote Control ID.  (p16)
iCANCEL button
Cancels the selection and returns to the previous menu.
(p34)
oINFO button
Displays the projector information.  (p31)
!3
INPUT 4-5 buttons
Selects input source (INPUT 4 - INPUT 5).  (p31)
Preparation 
						

							16
Preparation
This wireless remote control uses radio frequency signal.  You can switch four frequency channels prepared and select a
remote control ID from eight IDs.  The Remote Control Channel selection prevents radio frequency interference from the
other equipment and the Remote Control ID selection allows you to operate several projectors with their respective remote
controls without mutual interference among those projectors.
Wired Remote Control Transmitter
The remote control can be used as a wired remote control.  When
interference between the projector and other equipment occurs or
the projector is used in a place where the operation of radio
equipment is restricted, connect the remote control and the
projector with the remote control cable provided. Connected with
the remote control cable, the remote control does not emit radio
signal.
Remote Control Channel and ID Setup
Initial Remote Control Channel and ID are CH1 and ID1.  When
you change the setting, set a Channel first, and then an ID.
Channel and ID settings for the remote control should be the
same as those for the projector.  When changing the CH and ID
settings to the remote control, do it to the projector as well.  Refer
to Remote Control  in Setting menu on page 53.
Should you be lost at which CH and ID are currently set, initialize
the Channel and ID once, and set them again.
With holding down the CH button, press the SELECT button.
The Remote Control Channel switches sequentially for one
pressing the SELECT button.  (See Table1 on next page.) 
With holding down the CH and ID buttons together, slide the
REMOTE RESET/ON/ALL-OFF switch to REMOTE RESET,
and then to ON.  The initial Channel and ID are CH1 and ID1.
(p15)
1
MENUMENU
CANCEL CANCEL
INFOINFOAUTO PC
SCREENSCREENFREEZEFREEZE
P-TIMERP-TIMERSOUNDSOUND
REMOTEREMOTE
VOL.
MUTE
CH
ID
INPUT 4INPUT 1 
INPUT 2
INPUT 3 INPUT 5
REMOTE   RESET  ON   ALL OFF
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
While pressing the CH/ID
button, press the SELECT
button number of times
corresponding to the
remote control CH/ID. 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
ID button CH button
SELECT button
✔Note:
Remote Control Channel and ID cannot be initialized separately.   
Set the Remote Control Channel
Set the Remote Control ID
2
With holding down the ID button, press the SELECT button.
The Remote Control ID switches sequentially for one
pressing the SELECT button.  (See Table2 on next page.) 
Initialize the Remote Control Channel and ID
Remote Control Transmitter 
						

							17
Preparation
Remote Control Battery Installation
To insure safe operation, please observe the following precautions :
●Use (2) AA, UM3 or LR6 type alkaline batteries.
●Replace two batteries at the same time.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture, or heat.
●Do not drop the remote control.
●If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
●Risk of explosion if battery is replaced by an incorrect type. 
●Dispose of used batteries according to the instructions.  
Press the lid downward
and slide it.
Remove the battery
compartment lid.Slide the batteries into
the compartment.Replace the compartment
lid.
Two AA size alkaline
batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
12 3
✽ Default settingID 7
ID 8
Remote Control ID
ID 1 ✽ 
ID 2 
ID 3
ID 4
ID 5
ID 6
Remote Control CHRadio Frequency
CH 1 ✽ 2.472 GHz
CH 2 2.403 GHz
CH 32.446 GHz
CH 42.421GHz
Channel switches sequentially for
one pressing the SELECT button. ID switches sequentially for one
pressing the SELECT button. 
Table1: Remote Control Channel & Frequency
Table2: Remote Control ID
Preparation
Caution about Radio Wave
The remote control operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical
equipment (such as pacemaker), as well as amateur radio stations.   
Before operating the remote control, make sure no electromagnetic interference occurs and pay attention to the
following cautions.
1.  Be sure that there are no other devices in the area that may use the same frequency band as the remote 
control.
2.  If any other devices are causing radio interferences, change the communication frequency channel or 
move to other location.
Caution in Wireless LAN Interference
Under wireless LAN environment based on IEEE 802.11b and IEEE802.11g, the remote control may not operate
properly due to radio interferences.  The remote control is initially set to use 2.472 GHz band (CH1) corresponding
to several channels of wireless LAN.  
Should the remote control not operate properly due to radio interference, switch the communication frequency
channel to CH2.  Yet the operating condition is not improved, try CH3 and CH4.  In case of failure in every channel
operation, relocate other radio equipment using 2.4 GHz band away from the remote control and the projector. 
						

							18
Install the projector in a safe place.  Before installation, read Safety
Instructions thoroughly and check the installation place.  Install the
projector in a place with sufficient strength to support the
projectors weight.  Installation on an unstable stand, cart, or
ceiling may cause serious injury or accidents.  
Do not place the projector where is extremely hot and humid.  Do
not place the projector where is dusty and smoky.   When installing
the projector in dusty and smoky places or in a place for a long
period of time, installation with Smoke Resist Box (AH-69601)
separately supplied is recommended.  (p75)
When moving or setting up the projector, check the
followings again: 
–  Be sure that the lens is securely installed into the
projector.
– Be sure to replace Lens cap to protect lens
surface.  
–  Be careful not to hold or subject a lens to strong
forces.  It may damage lens, cabinet, or
mechanical parts.
This projector is designed to project on a flat surface.  Projector
should be perpendicular to the projection screen. Otherwise, the
projected image may be distorted.  Keystone function allows you
to correct image distortions, but it should be considered that the
keystone correction may lower the image resolution.  (p32)
Do not expose the projection screen to direct sunlight or
excessive ambient lighting.  The projected image may get white-
tinged due to reflection and the best image quality may not be
obtained.  SCREEN
Positioning the Projector
Before setting up the projector, install optional lens in the
projector.  Install the lens following the instructions in the Lens
Installation Manual provided.  Ask the sales dealer for detailed
information of optional lens specifications.  
Do not move the projector with holding the lens mounted and its
peripheral part.  It may cause serious damages to the projector and
the lens.
Lens Installation
Installation
Lens cap
Installation 
						

							19
Installation
Adjustable feet Lens shift feature is provided to move the position of the projected image vertically by 50% and horizontally by 10%
respectively without any image distortion.
✽Lens shift range varies depending on lens and projectors.  The range in this manual is the case of LNS-W04.
Level Adjustable Feet
This projector has four level adjustable feet.  The projection angle
can be adjusted by rotating each foot.  Adjust the four feet to
obtain best position of the projected image and make the
projector stable.  
The projection angle is adjustable up to 3.65 degrees upward and
downward respectively by rotating front and back feet.  
The projector can project image vertically and horizontally in the
range of 360 degrees.  For proper installation, refer to Setup In
Proper Directions on page 6.
Projection angle is adjustable up to 3.65 degrees
upward and 3.65 degrees downward by adjusting front
and back feet.
3.65° 3.65°
Lens Shift Adjustment
Installation
50%
50%10%10% 
						

							20
Installation
Connecting AC Power Cord
This projector uses nominal input voltages of 120 V or 200-240 V
AC.  This projector automatically selects correct input voltage.  It is
designed to work with single-phase power systems having a
grounded neutral conductor.  To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of the power being supplied.
Connect a projector with peripheral equipment before turning on it.
(Refer to p22 ~ 25 for connection.) 
Connect AC Power Cord (supplied) to
this socket.  AC outlet must be near
this equipment and must be easily
accessible.
Main On/Off switch
AC power socket
CAUTION
For safety, unplug AC power cord when the projector is not in
use.   When this projector is connected to an outlet with AC
power cord and the Main On/Off switch is on, the projector is in
stand-by mode and consumes a little electric power.
To the POWER CORD
CONNECTOR on the
projector.
Projector sideAC Outlet side
Ground
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below.  The proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
To the AC Outlet.(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
To the AC Outlet.(200 - 240 V AC)