Eiki Projector Lc Sb21 User Manual

11
Part Names and Functions
Part Names and Functions
Remote Control
q
w
e
r
t
y
u
i
o
!0
!1
!4
!5
!6
!7
!9
@0
@1!2
!3
@2
@2RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.” Set it to “ALL OFF” for
power saving when it is not used.  Slide this switch to RESET to initialize the
remote control code or switch Spotlight and Pointer back to Laser pointer.  (p12, 14)
wSIGNAL EMISSION indicator
This indicator lights red while the laser beam is being emitted from the laser light...

12
Part Names and Functions
Spotlight
Pointer Function
Pointer
✔Note:You can choose the size of Spotlight (Large, Middle, and Small) and the pattern of
Pointer (Arrow, Finger, and Dot) in the Setting Menu.  See “Pointer” on page 46.
This remote control emits a laser beam from the laser light window.  With the LASER button pressed, laser light goes on.
The signal emission indicator lights red and laser is emitted with red light.  With the LASER button pressed for more than 1
minute or released, the light...

13
Part Names and Functions
Part Names and Functions
The remote control can be used as a wireless mouse for your computer. Before operating the wireless mouse, connect
your computer and the projector with the supplied USB cable.  (See page 17 for connection.) 
When the Pointer function is used, the wireless mouse is not available. 
Move the pointer on the screen
with this button.  PRESENTATION POINTER button
R-CLICK button
L-CLICK button
Acts as right click while the
projector and a computer are...

14
Part Names and Functions
To insure safe operation, please observe the following precautions :
●Use (2) AA, UM3 or LR6 type alkaline batteries.
●Replace two batteries at the same time.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture, or heat.
●Do not drop the remote control.
●If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
●Risk of explosion if battery is replaced by an...

15
Installation
Projection angle can be adjusted up to 11.8 degrees with the
adjustable feet. 
Lift the front of the projector and pull upward the feet lock
latches on both sides of the projector.1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can...

To the POWER CORD
CONNECTOR on the
projector.
Projector sideAC Outlet side
Ground
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below.  The proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
To the AC Outlet.
(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
To the AC Outlet.
(200 - 240 V AC)
16
Installation
This projector...

17
Installation
Installation
Connecting to a Computer
ON ON
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
MCI
(MONO)
(VARIABLE)
AUDIO  OUT
Cables used for connection
• VGA Cable (HDB 15 pin) ✽
• DVI-VGA Cable (HDB 15 pin) 
• USB Cable
• Audio Cables (Mini Plug: stereo)
✽
(✽= Not supplied with this projector.)
External Audio Equipment
VGA cable ✽ USB cableAudio cable (stereo) ✽
Audio cable ✽
(stereo)...

18
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
(VARIABLE)
AUDIO  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
(MONO)
AUDIO  OUT
(VARIABLE)
COMPUTER  IN  1DVI - I
MONITOR  OUTCOMPUTER IN 2 / COMPONENT IN / 
RESET
MCI
Installation
Connecting to Video Equipment
Cables used for connection
• Video and Audio Cable (RCA x 3) ✽
• S-VIDEO Cable ✽
• Audio Cables (Mini...

19
Installation
Installation
Connecting to Component Video Equipment
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
(VARIABLE)
AUDIO  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
(MONO)
AUDIO  OUT
(VARIABLE)
COMPUTER  IN  1DVI - I
MONITOR  OUTCOMPUTER IN 2 / COMPONENT IN / 
RESET
MCI
Cables used for connection
• Audio Cables (Mini Plug (stereo) x 2 or RCA x 2) ✽
•...

20
Connect the projectors AC power cord into an AC outlet.
The POWER indicator blinks red in a moment and lights red.
Press the POWER ON-OFF button on the top control or on
the remote control.  The POWER indicator turns green
lighting and the cooling fans start to operate.  The
preparation display appears on the screen and the count
down starts. 
2
3
1
16
The preparation display disappears after 20 seconds.
4After the count-down, the input source that was selected
last and the Lamp mode status icon (see...