Eiki Projector Lc Hdt2000 User Manual

							
41

Image Adjust MenuPress the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Image 
adjust and then press the Point 8 or the SELECT 
button.
1
2Use the Point ed buttons to select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point 7 8 buttons to 
adjust the setting value.
Press the Point 7 button to decrease the contrast; press the 
Point 8 button to increase the contrast (from 0 to 63).
Press the Point 7  button to decrease the brightness; press 
the Point 8 button to increase the brightness (from 0 to 63).
Use the Point 7 8 buttons 
to adjust the setting value.
Selected Image mode
Image Adjustment
Computer Input
The Color Management function can be used to adjust the LEVEL, 
PHASE, and GAMMA of the selected display colors (except for 
black, white, and gray) on the screen and replace these colors with 
other colors if required.
You can store up to eight (8) color management data.
1Select and highlight Color Management by using the Point 
ed buttons and press the SELECT button. The projected 
image freezes, and the COLOR MANAGEMENT POINTER 
appears.
Use the Point ed7 8 buttons to move the pointer to the 
spot where you want to adjust the color and then press the 
SELECT button. The COLOR SELECTION window appears, 
and the color in the center of the pointer is selected and you 
can adjust the color.
2
Use the Point ed7 8 buttons to adjust the LEVEL and 
PHASE of the color, and then press the SELECT button to 
confirm the setting. Then use the Point ed buttons to adjust 
the GAMMA for the color and press the SELECT button to 
accept the setting. After adjusting, press the SELECT button 
to go to the COLOR MANAGEMENT LIST.
3
COLOR SELECTION MODE
Go to the COLOR MANAGEMENT LIST.
LIST
Return to the COLOR MANAGEMENT POINTER. (If you press 
the MENU button on the side control or the remote control , 
it returns to the COLOR MANAGEMENT POINTER and you 
will need to reselect and readjust the color.)
COLOR M.
COLOR MANAGEMENT POINTER
POINTER MODE
✔Note
When White  balance  Red,  Green  or  Blue  is  adjusted, 
Color temp. will change to Adj.
Contrast
Brightness
Color management 
						

							
42

Clear the check mark if you do not want to apply the adjusted 
color data; select the check mark and then press the SELECT 
button. The check mark disappears.
LIST MODE
Return to the COLOR SELECTION mode so that you can 
readjust the setting for the color in that line. (This option is 
not available if the check mark is cleared.)
Select the DEL box if you want to delete the adjusted data. 
Press the SELECT button and a confirmation box appears and 
then select [Yes]. 
Delete all the data in the list. Press the SELECT button and a 
confirmation box appears and then select [Yes].
The same function as stated above.
COLOR PALETTE
DEL
ALL DEL
COLOR M.
In the COLOR MANAGEMENT LIST, the adjusted color data 
are checkmarked. You can decide whether or not to apply the 
adjusted color data in the list to the projected image (see 
below).
4
MENU
The same function as stated above.
Level and phase adjustment palette.Gamma adjustment palette.
LISTCOLOR M.MENU
COLOR PALETTEDEL
ALL DELMENUCOLOR M.
COLOR SELECTION MODE
LIST MODE
Press the Point 7 button to lighten red tone; press the Point 
8 button to deepen red tone (from 0 to 63).
Press the Point 7 button to lighten green tone; press the 
Point 8 button to deepen green tone (from 0 to 63).
Press the Point 7 button to lighten blue tone; press the 
Point 8 button to deepen blue tone (from 0 to 63).
Use the Point 7 8 buttons to select the desired Color temp. 
level (XLow, Low, Mid or High). 
Return to the IMAGE ADJUST Menu. Any settings that 
have been changed will not be stored. To store the changed 
settings, be sure to select “LIST” and go to the COLOR 
MANAGEMENT LIST.
MENU
Computer Input
Color temp.
White balance (Red)
White balance (Green)
White balance (Blue) 
						

							
4

To reset the adjusted data, select Reset and press the 
SELECT button. A confirmation box appears and then select 
Yes. All adjustments will return to their previous figures. 
To store the adjusted data, select Store and press the 
Point 8 or the SELECT button. Use the Point ed buttons 
to select one from Image 1 to 10 and press the SELECT 
button. 
A confirmation box appears and then select Yes. Stored data 
can be called up by selecting an Image (1-10) in the Image 
Mode Selection on page 40.
Use the Point 7 8 buttons to adjust the gamma value to 
obtain a better balance of contrast (from 0 to 15).
Press the Point 7 button to decrease the sharpness of the 
image; press the Point 8 button to increase the sharpness 
of the image (from 0 to 31).
A confirmation box appears and then select Yes.
Computer Input
Use the Point 7 8 buttons to select the desired Auto picture 
control option (Off, L1 or L2).
 Off
  . . . .  Auto picture control OFF position.
  L1
. . . . .  Auto picture control LEVEL 1 position.
  L2
. . . . .  Auto picture control LEVEL 2 position.
Use the Point 7 8 buttons to select the advanced color mode.
  Off
  . . . .  Advanced color mode is “Off”.
  Auto
  . . . Advanced color according to the type of image.
*This function controls the operation of the Color Control 
Devic, which independently and automatically regulates the 
amount of yellow light passing through the LCD panel, to 
accurately reproduce both image color and image brightness. 
Normally leave Auto (default setting). 
✔Note:
• White balance may change depending on the image.
Auto picture control
Advanced color*
Sharpness
Gamma
Reset
Store
Press the Point 7 button to lighten red/green/blue tone 
of the black level of an image; press the Point 8 button to 
deepen red/green/blue tone of the black level of an image.
Offset (Red/Green/Blue) 
						

							
44

Select the desired screen size that conforms to the input signal 
source.
Screen menu
Provides the image within a screen size keeping its original aspect ratio.
✔Note
• The  projector  cannot  display  any  resolution  higher  than 
2048  x  1080.  If  your  computer’s  screen  resolution  is 
higher  than  2048  x  1080,  lower  the  resolution  before 
connecting the projector.
•  The image data other than 2048 x 1080 is modified to fit 
the screen size in initial mode.
•  Full, Wide(16:9), Zoom, True and Digital zoom +/– cannot 
be  selected  when  no  signal  is  detected  in  the  PC 
System Menu. (p.36)
•  You cannot zoom out  an image smaller than normal size 
for display in Custom mode.
1
2
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Screen and 
then press the Point 8 or the SELECT button.
Use the Point ed buttons select the desired item and then press the SELECT button.
Screen Size Adjustment
Displays an image based on the output resolution from the 
computer
- Less than the panel resolution (2048x1080)
The image is centered on the screen.
- Equal to the panel resolution (2048x1080) 
"Normal" appears at a corner of the screen.
- Higher than the panel resolution (2048x1080) 
Panning mode begins with "True" displayed on the screen. 
In this case, the Zoom function is not available.
When the original image size is larger than the panel size 
(2048x1080), the projector enters to the panning mode 
automatically. Use the Point ed7 8 buttons to pan the image. 
When adjusted, the arrows will turn red. When reached to the 
correction limits, the arrows will disappear.
Scales the image proportionally to fit the entire screen. Either side of image may go over the screen.
Provides the image to fit full screen size.
Provides the last stored aspect screen image. 
Provides the image at the 16:9 wide screen ratio.
Computer Input
Normal
Full
Wide (16:9)
Zoom
True
Custom 
						

							
45

Adjust the screen scale and position manually with this 
function.
Press the Point 8 button or the SELECT button at Custom 
adj. and Custom adj. is displayed on the screen, you can 
use the Point ed buttons to choose the item you want to 
adjust.
 Scale H/V  ...........  Adjusts the Horizontal/Vertical screen 
scale.
  H&V  ...................  When set to On, the aspect ratio is 
fixed. Scale V appears dimmed and 
becomes unavailable. Adjust Scale H, 
then the screen scale is automatically 
modified based on the aspect ratio. 
  Position H/V  .......  Adjusts the Horizontal/Vertical screen 
position.
  Common  ............  Saves the adjusted scale to all the 
inputs. Press the SELECT button at 
Common to display a confirmation box. 
To save the scale, press the SELECT 
button at Yes. When Custom is selected, 
the saved scale is used.
  Reset  .................  Resets the all adjusted values. Press 
the SELECT button at Reset to display 
a confirmation box. To reset, press the 
SELECT button at Yes.
✔Note
• When  no  signal  is  detected,  Normal  is  set  automatically 
and the Aspect dialog box disappears.
• The  adjustable  range  for  Scale  H/V  and  Position  H/V  is 
limited depending on the input signal.
Selects Digital zoom +. The On-Screen Menu disappears and 
D.  zoom  +  appears.  Press  the  SELECT  button  to  expand  the 
image size. Use the Point ed7 8 buttons to pan the image. 
The Panning function can work only when the image is larger 
than the screen size.
You can also enter the Digital zoom + mode by pressing the 
D.ZOOM button on the remote control.
You  can  also  enter  the  Digital  zoom  -  mode  by  pressing  the 
D.ZOOM button on the remote control.
Selects Digital zoom – . The On-Screen Menu disappears and 
D.  zoom  –  appears.  Press  the  SELECT  button  to  compress 
image size. 
The  projected  image  can  be  also  compressed  by  pressing 
the D.ZOOM button on the remote control.
To  return  to  the  previous  screen  size,  select  a  screen  size 
from  the  Screen  Size  Adjustment  Menu  or  select  an  input 
source from the Input Source Selection Menu (see pages 33-
35) again or adjust the screen size with the D.ZOOM button.
✔Note:
• The  panning  function  may  not  operate  properly  if  the 
stored Mode in the PC adjust Menu is used (p.39).
• The minimum compression ratio is limited depending on 
the  input  signal,  when  the  Keystone  function  is  working 
or when the custom is selected for the screen size.
• True  and  Digital  zoom  +/–  cannot  be  selected  when 
480i,  575i,  480p  or  575p  is  selected  in  the  PC  System 
Menu (p.36).
•  Digit al  zoom  +/-  cannot  be  selected  when  True  is 
selected.
•  Digital  zoom  –  cannot  be  operated  when  Custom  is 
selected.
Computer Input
Custom adj.
Digital zoom +
Digital zoom – 
						

							
46

This function is used to adjust keystone distortion of the  
projected image. Use the Point ed buttons to choose the 
item you want to adjust.
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at Yes.
Ceiling 
Rear 
When this function is set to On, the picture will be top/
bottom and left/right reversed. This function is used to 
project the image from a ceiling-mounted projector.
When this function is set to On, the picture will be left/right 
reversed. This function is used to project the image from 
rear of the screen.
Adjusts the Horizontal/Vertical keystone distortion of the  
projected image.
Standard
Corner correction
Adjusts the corner distortion of the projected image.
Corner pattern
Choose a Corner pattern mode among Red, White, Blue, 
and Off.  
 Store
Store ..........  
Keeps the keystone correction even when the 
AC power cord is unplugged.
Reset .........  
Releases the keystone correction when the AC 
power cord is unplugged.
Press the KEYSTONE button on the remote control to switch 
the Standard (for Vertical/Horizontal) /Corner correction 
adjustment. The Standard or Corner correction adjustment 
dialog box appears. Use the Point ed7 8 buttons to correct 
the Standard or Corner distortion.  (p.32) 
This function is used to scale the input source to fit the 
screen. Select one of the following aspect ratio which is 
suitable for your cable and computer. Select “Full” if you do 
not want to set aspect ratio.
Full .......Flexible aspect ratio
16:9  ......16:9 aspect ratio
16:10  ....16:10 aspect ratio
4:3  .......4:3 aspect ratio
✔Note
• When the 16:9 function is selected, Wide(16:9) is not 
available in the PC and AV screen (pp.44, 52).
Computer Input
Keystone
Ceiling
Rear
Screen aspect
Reset 
						

							
47

If the projector cannot reproduce proper video image, 
select a specific broadcast signal format from among PAL, 
SECAM, NTSC, NTSC 4.4, PAL-M, and PAL-N.
The projector automatically detects an incoming video signal, 
and adjusts itself to optimize its performance.
When the Video System is   105i, 1080i or 1080p, select the 
system manually.
If the projector cannot reproduce proper video image, select 
a specific component video signal format from among 480i, 
575i, 480p, 575p, 720p, 105i, 1080i, and 1080p.
Video Jack or S-video Jack
The projector automatically detects an incoming video 
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the 
system manually.
Video Input
1AV System menu (Video or S-video)
AV System menu (y , Pb/Cb, Pr/Cr)
2
Press the MENU button to display the On-Screen Menu.  
Use the Point ed buttons to select Input and then 
press the Point 8 or the SELECT button. 
Use the Point ed buttons to select System and then 
press the Point 8 or the SELECT button. 
Use the Point ed buttons to select the desired system 
and then press the SELECT button.
✔Note:
The AV System Menu cannot be selected when selecting RGB 
(Scart).
Video System Selection
y, Pb/Cb, Pr/Cr Jacks
Auto
PAL/SECAM/NTSC/NTSC4.4/PAL-M/PAL-N
Auto
y, Pb/Cb, Pr/Cr SIGNAL FORMAT 
						

							
48

Video Input
Normal picture level preset on the projector.
Picture level adjusted with fine tone.
User preset picture adjustment in the Image adjust 
Menu. (p.51)
Image select menu
1
2
Press the MENU button to display the On-Screen Menu. 
Use the Point ed buttons to select Image select and 
then press the Point 8 or the SELECT button.
Use the Point ed buttons to select the desired item 
and then press the SELECT button.
Image Selection
Menu Operation
For viewing pictures in a bright room.
Dynamic
Standard
Cinema
Image 1–10 
						

							
49

Video InputVideo Input
1
2
Press the Point 7 button to decrease the contrast; press 
the Point 8 button to increase the contrast (from 0 to 63).
Press the Point 7 button to decrease the brightness; 
press the Point 8 button to increase the brightness (from 
0 to 63).
Press the Point 7 button decrease the intensity of the 
color; press the Point 8 button increase the intensity of 
the color (from 0 to 63).
Press the Point 7 8 buttons to adjust the tint value to get 
a proper color balance (from 0 to 63).
Image adjust
Selected Image mode
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Image 
adjust and then press the Point 8 or the SELECT 
button.
Use the Point ed buttons select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point 7 8 buttons to 
adjust the setting value.
Use the Point 7 8 
buttons to adjust 
the setting value.
Image Adjustment
Refer to pages 41 and 42.
Press the Point 7 button to lighten red tone; press the 
Point 8 button to deepen red tone (from 0 to 63).
Press the Point 7 button to lighten green tone; press the 
Point 8 button to deepen green tone (from 0 to 63).
Press the Point 7 button to lighten blue tone; press the 
Point 8 button to deepen blue tone (from 0 to 63).
Use the Point 7 8 buttons to select the desired Color temp. 
level (XLow, Low, Mid or High). 
Contrast
Brightness
Color management
Color
Tint
Color temp.
White balance (Red)
White balance (Green)
White balance (Blue) 
						

							
50

✔Note
• When White balance Red, Green or Blue is adjusted, the 
Color temp. level will change to Adj..
• Tint cannot be selected when the video system is PAL, 
SECAM, PAL-M or PAL-N (p.47).
Press the Point 7 button to lighten red/green/blue tone 
of the black level of an image; press the Point 8 button to 
deepen red/green/blue tone of the black level of an image 
(from 0 to 63).
Use the Point 7 8 buttons to select the desired Auto picture 
control option (Off, L1 or L2).
 Off
  . . . .  Auto picture control OFF position.
  L1
. . . . .  Auto picture control LEVEL 1 position.
  L2
. . . . .  Auto picture control LEVEL 2 position.
Use the Point 7 8 buttons to select the advanced color mode.
  Off
  . . . .  Advanced color mode is “Off”.
  Auto
  . . . Advanced color according to the type of image.
*This function controls the operation of the Color Control 
Device, which independently and automatically regulates the 
amount of yellow light passing through the LCD panel, to 
accurately reproduce both image color and image brightness. 
Normally leave Auto (default setting). 
✔Note:
• White balance may change depending on the image.
Video Input
Auto picture control
Advanced color*
Sharpness
Gamma
Offset (Red/Green/Blue)
Use  the  Point 7 8 buttons  to  adjust  the  gamma  value  to 
obtain a better balance of contrast (from 0 to 15).
Press the Point 7 button to decrease the sharpness of the 
image; press the Point 8 button to increase the sharpness 
of the image (from 0 to 31).