Eiki Projector Lc Hdt10 User Manual

							21
BEFORE OPERATION
MENU BAR
SETTING MENU
Used to change settings
of projector or reset Lamp
Replace Counter. 
(Refer to P35-38)
GUIDE WINDOW
Shows selected
item of ON-
SCREEN MENU.
SYSTEM BOX
Used to select computer
system or video system.
Shows selected system
on this box. 
(Refer to P26-27)
INPUT MENU
Used to select input
source (Input 1, Input 2,
Input 3 or Input 4). Refer
to P25.
SOUND MENU
Used to adjust sound[volume, Bass or Treble],to select Built-in SP On-
Off and Sound Mute. 
(Refer to P24)
IMAGE ADJUST MENU
Used to select image level among Standard (AV),
Cinema, Standard (PC), Real and Image 1 ~ 10.
(Refer to P32)
Used to adjust image. 
[Contrast/Brightness/Color/Tint/Color Temp.
/White Balance (R/G/B)/Sharpness/Detail
Enhancer /Gamma/Noise
Reduction/Progressive/Auto picture control/Auto
Lamp Control] (Refer to P33-34)
DISPLAY ADJUST MENU
Used to adjust size of
image.
{Full/Normal/Anamorphic}
(Refer to P28)
Used to adjust parameters
to match with input signal
format. (Refer to P30-31) 
						

							22
BASIC OPERATION
TURNING ON PROJECTOR
TURNING OFF PROJECTOR
TURNING ON / OFF PROJECTOR 
Connect a projectors AC Power Cord into a wall outlet and turn
MAIN ON/OFF SWITCH to ON. LAMP indicator lights RED, and
READY indicator lights GREEN.
Press POWER ON-OFF button on Side Control or on Remote
Control Unit to ON. LAMP indicator dims, and Cooling Fans start
to operate. Preparation Display appears on a screen and count-
down starts.  Signal from source appears after 30 seconds.
Current Input and Lamp status are also displayed on screen for
5 seconds. (Refer to LAMP MANAGEMENT on page 40.)
2
3
Press POWER ON-OFF button on Side Control or on Remote
Control Unit, and a message Power off? appears on a screen.  1
2
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
1Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to CONNECTING TO
PROJECTOR on Pages 12~15 for connecting that equipment.)
3
30
Preparation Display disappears after
30 seconds.
Press POWER ON-OFF button again to turn off projector. LAMP
indicator lights bright and READY indicator turns off.  After
approximate 90 seconds, READY indicator will light green again
and projector may be turned on by pressing POWER ON-OFF
button.
Cooling fans will operate for approximate 2 minutes after projec-
tor is turned off. To power down completely, turn MAIN ON/OFF
SWITCH to OFF and disconnect AC Power Cord.
INPUT AND LAMP STATUS
Message disappears after 4 seconds.
When WARNING TEMP. Indicator is flashing, projector cannot be turned on, refer to the section MAINTENANCE on page 39.
When the both WARNING TEMP. and READY Indicator flashing, refer to the section MAINTENANCE on page 39. 
When “Power Management” function mode is Ready or Shut down, projector detects signal interruption and turns off the
Projection Lamp automatically.  Refer to “Power management” on page 37.
Do not use the projector continuously for 24 hours or more. If using the projector continuously for long periods,
turn it off and leave it for one hour at least once during a 24 hour period. 
If you use the projector continuously for long period, it can excessively shorten the life of the lamp.  
						

							23
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
1Press ZOOM /button on Side Control or on Remote Control
Unit. Message “Zoom” is displayed.
2Press ZOOM button to make image larger, and press ZOOM
button to make image smaller.
1Press FOCUS /button on Side Control or on Remote Control
Unit. Message “Focus” is displayed.
2Adjust focus of image by pressing FOCUS /button(s) .
LENS SHIFT ADJUSTMENT
Message disappears after 4 seconds.
1Press the LENS SHIFT button on Side Control or on the Remote
Control Unit.  Message “Lens shift” is displayed.
2Press POINT UP button to move image up, press POINT DOWN
button to move image down, press POINT LEFT to move image
left and press POINT RIGHT to move image right.
Message disappears after 4 seconds.
Message disappears after 4 seconds.
Press FREEZE button on Remote Control Unit to freeze picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button.
Press NO SHOW button on Remote Control Unit to black out image.
To restore to normal, press NO SHOW button again or press any
other button.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
Message disappears after 4 seconds. 
						

							24
BASIC OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon. 
Volume
Press VOLUME (+/–) button(s) on Side Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound.  To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing. 
Press POINT LEFT/RIGHT button(s) to cut off sound.  Dialog box
display is changed to “On” and sound is cut off.  To restore sound to
its previous level, press POINT LEFT/RIGHT button(s) again.
Press POINT DOWN button to move a red frame pointer to item
that you want to select, and then press SELECT button.
SOUND ADJUSTMENT
DIRECT OPERATION
MENU OPERATION
Volume
Mute
Treble
To adjust Treble sound, press POINT RIGHT button or POINT LEFT
button. 
Bass
To adjust Bass sound, press POINT RIGHT button or POINT LEFT
button. 
Built-in SP.
Closes SOUND MENU.
Quit
Press POINT LEFT/RIGHT button(s) to switch built-in speaker on and
off.
Close SOUND Menu.
Indicates roughly level of
volume.
Press MUTE button to set
Mute function On or Off.
Display disappears after 4 seconds.  
SOUND MENU
SOUND Menu icon
Indicates roughly
level of volume. 
						

							25
BASIC OPERATION
When connect component video output (Cr, Y, Cb or Pr, Y, Pb) from
video equipment to R/Pr, G/Y and B/Pb jacks.
WHEN SELECT INPUT 2 (5 BNC TERMINAL)
WHEN SELECT  INPUT 1 (SDI TERMINAL )
Input 1
INPUT MENU
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Select INPUT source by pressing INPUT 1/2 and INPUT 3/4
buttons on Side Control or INPUT 1, INPUT 2, INPUT 3 and
INPUT 4 on Remote Control Unit.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to select Input and press SELECT
button. 
Another dialog box INPUT SELECT Menu will appear. 
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to INPUT source that you want to select, and then
press SELECT button.  
1
2
INPUT 1/2 button
INPUT 1
INPUT 2
Input 2
INPUT 3/4 button
INPUT 3
INPUT 4
INPUT 1-4 buttons
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT Menu icon
Move arrow to INPUT source
that you want to select, and
then press SELECT button.  
WHEN SELECT  INPUT 3 (DVI TERMINAL)
Input 3
When your computer is connected to INPUT 3 (DIGITAL) terminal,
select RGB(PC Digital).
RGB(AV HDCP)
When your computer is connected to INPUT 3 (ANALOG) terminal,
select RGB(Analog).
RGB(Analog)
RGB(PC Digital)
RGB(Scart)
When video equipment is connected to INPUT 3 (ANALOG) terminal,
select RGB(Scart).
If a HDCP-compatible signal source is connected to the INPUT 3
(DIGITAL) terminal, select RGB(AV HDCP).
NOTE;
HDCP (High-bandwidth Digital Content
Protection) is a system for protecting digital
entertainment content which is delivered by DVI
(Digital Visual Interface) from being copied.
The specification of HDCP is decided and
controlled by Digital Content Protection, LLC.
Should the specification be changed, this
projector may not display the digital content
protected by HDCP.
Move a pointer to either SDI 1 or SDI 2 and press SELECT button.
RGB
Y, Pb/Cb, Pr/Cr
Move a pointer to source that you want to select and press SELECT
button.
Move a pointer to source that you want to select and press SELECT
button.
When connect a computer output [5 BNC Type (Red, Green, Blue,
Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb,
H/HV and V jacks. 
						

							26
BASIC OPERATION
SYSTEM SELECT
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA or UXGA (refer
to “COMPATIBLE COMPUTER SPECIFICATION” on pages 50-51). When a computer is selected, this projector
automatically tunes to incoming signal and projects the proper image without any special setting. (Some computers need to
be set manually.) 
The projector displays one of the Auto, -----, Mode 1 ~ Mode 20, or the system provided in the projector.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon.
When image is not provided properly, manual adjustment
is required.  (Refer to P30 and 31.)
There is no signal input from computer. Make sure
connection of computer and a projector is set correctly.  
(Refer to TROUBLESHOOTING on page 43.)
Auto
––––
SYSTEM Menu icon
Displays system being
selected.
SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM SELECT Menu icon.
Press POINT UP/DOWN button to move a red arrow pointer to
system that you want to set, and then press 
SELECT button.  
1
2
SYSTEM SELECT MENU (PC)
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
AUTOMATIC MULTI-SCAN SYSTEM
SYSTEM SELECT Menu icon 
Displays system being selected.
Systems on this dialog box can
be selected.
Custom Mode (1 ~ 20) set
in DISPLAY ADJUST
Menu.  (P30, 31)
User preset adjustment in MANUAL PC ADJUSTMENT.
Adjustment data can be stored in the Mode 1-20.Mode 1
Computer systems provided in the projector. The
projector chooses proper system and displays it.SVGA 1
Mode 1 and SVGA 1 are examples.✽ 
						

							27
BASIC OPERATION
SYSTEM SELECT MENU (SDI)
SYSTEM  SELECT Menu icon 
Displays system being selected.
Systems on this dialog box can
be selected.
Custom Mode (1~15) set in
DISPLAY ADJUST Menu.
(P30, 31)
SYSTEM SELECT MENU (Component video)
SYSTEM SELECT Menu icon 
Displays system being selected.
Systems on this dialog box can
be selected.
Custom Mode (1~15) set in
DISPLAY ADJUST Menu.
(P30, 31)
SELECT VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SYSTEM SELECT Menu icon.
Press POINT DOWN button to move a red arrow pointer to
system that you want to select and then press SELECT button.
1
2
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i, 1080i/50 or 1080i/60, select system
manually first.
If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i , 1080i/50 or 1080i/60.
Auto
COMPONENT VIDEO SIGNAL FORMAT
SDI Input 
Component video (Y, Pb/Cb, Pr/Cr) Input
Projector automatically detects incoming SDI signal (480i, 575i, 1035i,
1080i/60, 1080i/50, 720p, 1080p/30 and 1080psf/30), and adjusts itself
to optimize its performance.
When System is 1080i/60 or 1080psf/30, select system manually first. 
						

							28
DISPLAY ADJUST
DISPLAY ADJUSTMENTS
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
DISPLAY ADJUST Menu icon.1
Press POINT UP/DOWN button and move a red frame pointer to
Screen and then press SELECT button.2
Anamorphic
Provides image to fit the horizontal size of the screen size.
Full
Normal
Provides image in its original size.
Provides image is forcibly changed to a 4:3 image, even if the input
signal is HDTV.
Aspect HAspect V
These adjust the horizontal and vertical scale and position of the
screen. When a SELECT button is pressed, the mode changes to
Scale or Position adjustment mode. Use the POINT LEFT/RIGHT
button(s) to select whether you wish to adjust Scale or Position, and
then use the POINT UP/DOWN button(s) to adjust the values.
DISPLAY ADJUST MENU
DISPLAY ADJUST Menu icon
Set a red frame pointer
to item and press
SELECT button.
3Press POINT UP/DOWN button to move a red arrow to level that
you want to set and then press SELECT button.
SCREEN ADJUSTMENTS
Select screen by pressing Screen button on Remote Control Unit.
Full
Normal
Anamorphic
SCREEN ADJUSTMENT (DIRECT) 
						

							29
DISPLAY ADJUST
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer.  Auto PC Adjustment function can be operated as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
DISPLAY ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Side Control or on Remote Control
Unit.
Auto PC Adj.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in SYSTEM SELECT Menu (P26).  Refer
to step 3 of MANUAL DISPLAY ADJUSTMENT section (P31).
NOTE
Fine sync, Total dots and Picture Position of some computers can
not be fully adjusted with this Auto PC Adjustment function. When
image is not provided properly through this function, manual
adjustments are required.  (Refer to page 30, 31.)
Auto PC Adjustment function cannot be operated in Digital Signal
input on DVI terminal and “480i”, “575i”, “480p”, “575p”, “720p
(HDTV)”, “1035i (HDTV)”, “1080i/50 (HDTV)” or “1080i/60 (HDTV)”
is selected on SYSTEM SELECT Menu (P26).
DISPLAY ADJUST MENU
DISPLAY ADJUST Menu icon
Set a red frame pointer
to item and press
SELECT button. 
						

							30
DISPLAY ADJUST
MANUAL DISPLAY ADJUSTMENTS
This projector can automatically tune to display signals from most computers and video equipments currently distributed.
However, some computers and video equipments employ special signal formats which are different from standard ones and
may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and
image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual display adjustment to enable you to precisely adjust several parameters to match with those
special signal formats.
This projector has 20 independent memory areas {Mode 1~15 for video equipments and computers (digital signal),  Mode 16
~ 20 for computers (analog signal)} to memorize those parameters manually adjusted. This enables you to recall setting for a
specific computer and video equipment whenever you use it. 
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT UP/DOWN button to move a red frame pointer to
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear.  Press POINT LEFT/RIGHT
button to adjust value.
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT button to adjust value. (From 0 to 31.)
Fine sync
Adjust the number of total dots in one horizontal period. Press
POINT LEFT/RIGHT button(s) and adjust number to match your PC
image.
Total dots
Adjusts horizontal picture position.  Press POINT LEFT/RIGHT
button(s) to adjust position.
Horizontal
Adjusts vertical picture position. Press POINT LEFT/RIGHT button(s)
to adjust position.
Vertical
Shows status
(Stored / Free) of
selected Mode. Selected Mode
DISPLAY ADJUST MENU
DISPLAY ADJUST Menu icon
Move a red frame icon to item and
press SELECT button.
Press POINT LEFT/RIGHT
button to adjust value.
Press SELECT button at this icon to
display next items. 
Selects area displayed with this projector. Select resolution at
Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area H
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area V
Display area
Press SELECT button at
Display area icon and Display
area dialog box appears.
Press SELECT button at this
icon to display previous items. 
Press POINT LEFT/RIGHT
button to adjust value.