Eiki Projector EK-612X User Manual

							— 26 — 
DLP Projector — Owner’s Manual
maIn menUsUb menU / settIngsDefaULt
OPTION
Information
Serial Number
Native Resolution
Firmware
Main Source
- Resolution
- Signal Format
- Pixel Clock
- Horz Refresh
- Vert Refresh
Sub Source
- Resolution
- Signal Format
- Pixel Clock
- Horz Refresh
- Vert Refresh
Light Source Mode
Total Projector Hours
Standby Power Mode
IP Address
DHCP
Factory ResetYes/No (Dialog box)
Service  
						

							— 27 — 
DLP Projector — Owner’s Manual
Picture Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select PICTURE and press 
the Enter button to enter the PICTURE menu. Press the arrow keys (pq) to select the menu option 
and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust the 
desired settings and press the Enter button to confirm.
Display Mode
Brightness
Contrast
Sharpness
Color
Tint
Phase
Frequency
Horz Position
Vert PositionPICTUREOUTPUT SETUP
OPTIONPICTURE
Presentation 50
502
50
50
50
50
50
50
ItemDescrIptIon
Display ModeOptimize the projector for displaying images under certain conditions, s\
uch 
as Presentation, Video, Bright, 2D High Speed, 3D, and user-definable 
preset.
BrightnessAdjust the intensity of the image.
ContrastAdjust the degree of difference between the lightest and darkest parts of 
the picture and change the amount of black and white in the image.
SharpnessSelect the edge clarity of the image.
ColorAdjust a video image from black and white to fully saturated color. The color 
setting applies to video sources only.
TintAdjust the red-green color balance in the image of video images. The tint 
setting applies to video sources only.
PhaseAnalog signals only. Adjust pixel phase when the image still shows shimmer 
or noise after pixel tracking is optimized. Pixel phase can adjust the p\
hase 
of the pixel-sampling clock relative to the incoming signal.
FrequencyAnalog signals only. Steady flickering or several soft vertical stripes or 
bands across the entire image indicates poor frequency. Proper frequency 
ensures that the image quality is consistent across the screen, the aspe\
ct 
ratio is maintained, and that the pixel phase can be optimized.
Horz PositionMove the image right or left within the area of available pixels.
Vert PositionMove the image up or down within the area of available pixels.
Auto ImageForce the projector to reacquire and lock to the input signal. This is useful 
when signal quality is marginal.
3D DisplayConfigure the color management settings. See “3D Display Menu” on page 
28.
HSG AdjustmentConfigure the color management settings. See “HSG Adjustment Menu” on 
page 28.
AdvancedConfigure the advanced image settings. See “Advanced Menu” on page 
30.   
						

							— 28 — 
DLP Projector — Owner’s Manual
3D Display Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select PICTURE and press 
the Enter button to enter the PICTURE menu. Press the arrow keys (pq) to select 3D Display and press 
the Enter button to enter the 3D Display menu. Press the arrow keys (pq) to select the menu option 
and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust the 
desired settings and press the Enter button to confirm.
3D Enable
3D InvertPICTUREOUTPUT SETUP
OPTION3D Display
Off
ItemDescrIptIon
3D EnableSet 3D format. Supports Mandatory 3D formats and frame sequential 
3D@120Hz.
3D InvertInvert 3D sync signal for the application of using single projector.
HSG Adjustment Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select PICTURE and press 
the Enter button to enter the PICTURE menu. Press the arrow keys (pq) to select HSG Adjustment 
and press the Enter button to enter the HSG Adjustment menu. Press the arrow keys (pq) to select the 
menu option and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or 
adjust the desired settings and press the Enter button to confirm.
HSG Enable
Auto Test Pattern
Red H.
Red S.
Red G.
Green H.
Green S.
Green G.
Blue H.
Blue S.PICTURE
OUTPUT SETUP
OPTIONHSG Adjustment
Off
Off
127
127
127
127
127
127
127
127  
						

							— 29 — 
DLP Projector — Owner’s Manual
ItemDescrIptIon
HSG EnableEnable/Disable the HSG adjustment function.
Auto Test PatternSet to “On” to enable displaying a test pattern for the target col\
or or set to 
“Off” to disable the auto test pattern.
Red H. / Green H. / 
Blue H. / Cyan H. /
Magenta H. / Yellow H.
Adjust the hue of the red, green, blue, cyan, magenta, or yellow channel\
 of 
the image.
Red S./ Green S./
Blue S./ Cyan S./ 
Magenta S./ Yellow S.
Adjust the saturation of the red, green, blue, cyan, magenta, or yellow \
channel of the image.
Red G. / Green G. /
Blue G. / Cyan G. /
Magenta G. / Yellow G.
Adjust the gain of the red, green, blue, cyan, magenta, or yellow channe\
l of 
the image.
White R Gain / 
White G Gain /
White B Gain
Adjust the white balance of the red, green, or blue channel of the image\
.
Reset to DefaultReset the hue, saturation, gain, and white balance adjustments to the 
factory defaults.  
						

							— 30 — 
DLP Projector — Owner’s Manual
Advanced Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select PICTURE and press 
the Enter button to enter the PICTURE menu. Press the arrow keys (pq) to select Advanced and press 
the Enter button to enter the Advanced menu. Press the arrow keys (pq) to select the menu option 
and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust the 
desired settings and press the Enter button to confirm.
White Peaking
Gamma
Color Temperature
Color Space
Color Settings
Film Mode
DynamicBlack
TM
PICTUREOUTPUT SETUP
OPTIONAdvanced
100
VIdeo Bright Auto
Off
Off
ItemDescrIptIon
White Peaking(Video source only) Increase the brightness of whites that are near 100%.\
GammaSelect the appropriate gamma from Film, Video, Graphics, and Standard.
Color TemperatureChange the intensity of the colors. Select a listed relative warmth valu\
e.
Color SpaceSelect a color space that has been specifically tuned for the input signal. 
Use only for analog signals and certain digital sources.
Color SettingsAdjust the gain of the red, green, or blue channel of the image. It will\
 affect 
the black and white. 
Adjust the offset of the red, green, or blue channel of the image. It will affect 
the black and white.
Reset RGB gain/offset to return the factory default settings for color 
adjustments.
Film ModeControl film mode detection and determine whether the original source of 
the input video was film or video.
DynamicBlackTMEnable or disable the dynamic black function. Enable this function raise\
s 
the contrast ratio dynamically.  
						

							— 31 — 
DLP Projector — Owner’s Manual
Output Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select OUTPUT and press 
the Enter button to enter the OUTPUT menu. Press the arrow keys (pq) to select the menu option 
and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust the 
desired settings and press the Enter button to confirm.
Aspect Ratio
Overscan
H Digital Zoom
V Digital Zoom
H Digital Shift
V Digital Shift
Image Warping
PIP/PBPPICTUREOUTPUT SETUP
OPTIONOUTPUT
Auto Off
100
100 50
50
ItemDescrIptIon
Aspect RatioDisplay an image with the detected size, or resize the image by maximizi\
ng 
either the height, width or both, or resize to the maximum size possible\
 
while keeping the original aspect ratio.
OverscanRemove noise around the image. Overscan Zoom enlarges image 3% 
from original size. Overscan Crop cuts 3% of active pixels in four edges\
 of  
original image.
H Digital ZoomChange the size of projector’s display area horizontally. If the display area 
has been resized by this setting, it can be moved by changing the H Digi\
tal 
Shift and V Digital Shift settings.
V Digital ZoomChange the size of projector’s display area vertically. If the display area has 
been resized by this setting, it can be moved by changing the H Digital \
Shift 
and V Digital Shift settings.
H Digital ShiftMove the display area horizontally if its size has been changed by the 
Digital Zoom setting.
V Digital ShiftMove the display area vertically if its size has been changed by the Dig\
ital 
Zoom setting.
Image WarpingConfigure the image warping settings. See “Image Warping Menu” on page 
32.
PIP/PBPConfigure the PIP/PBP settings. See “PIP/PBP Menu” on page 33.  
						

							— 32 — 
DLP Projector — Owner’s Manual
Image Warping Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select OUTPUT and press 
the Enter button to enter the OUTPUT menu. Press the arrow keys (pq) to select Image Warping and 
press the Enter button to enter the Image Warping menu. Press the arrow keys (pq) to select the menu 
option and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust 
the desired settings and press the Enter button to confirm.
H Keystone
V Keystone
H Pincushion
V PincushionPICTUREOUTPUT SETUP
OPTIONImage Warping
20
20
50
50
ItemDescrIptIon
H KeystoneAdjust the keystone horizontally and make a squarer image.
Horizontal keystone is used to correct a keystoned image shape in which \
the left and right borders of the image are unequal in length. This is 
intended for use with horizontally on-axis applications.
V KeystoneAdjust the keystone vertically and make a squarer image.
Vertical keystone is used to correct a keystoned image shape in which the\
 
top and bottom are slanted to one of the sides. This is intended when for 
use with vertically on-axis applications.
H PincushionAdjust the pincushion horizontally and make a more square image.
V PincushionAdjust the pincushion vertically and make a more square image.  
						

							— 33 — 
DLP Projector — Owner’s Manual
PIP/PBP Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select OUTPUT and press 
the Enter button to enter the OUTPUT menu. Press the arrow keys (pq) to select PIP/PBP and press 
the Enter button to enter the PIP/PBP menu. Press the arrow keys (pq) to select the menu option 
and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust the 
desired settings and press the Enter button to confirm.
PIP/PBP Enable
Main Source
Sub Source
Swap
Size
LayoutPICTUREOUTPUT SETUP
OPTIONPIP/PBP
On
VGA
DVI-D
Large
PBP, Main Left
ItemDescrIptIon
PIP/PBP EnableToggle between displaying two sources at once (Main and PIP/PBP 
images) or one source only.
Main SourceFrom the list of active inputs, select one to be used as the main image.\
Sub SourceFrom the list of active inputs, select one to be used as the PIP/PBP.
SwapChange the main image to PIP/PBP, and the PIP/PBP to main image. 
Swapping is available only when PIP/PBP is enabled.
SizeSelect the PIP/PBP size. Available options: Small, Medium, or Large.
LayoutSet the location of the PIP/PBP image on the screen.
PIP/PBP layout and size table as described below.
 ¾P : indicates primary source region (lighter color).
 ¾* : Both source regions are the same size.
pIp/pbp  LayoUtpIp/pbp sIZe
smaLLmeDIUmLarge
PBP, Main Left
PPP
PBP, Main TopPPP
PBP, Main Right
PPP  
						

							— 34 — 
DLP Projector — Owner’s Manual
pIp/pbp LayoUtpIp/pbp sIZe
smaLLmeDIUmLarge
PBP, Main Bottom
PPP
PIP-Bottom RightPPP
PIP-Bottom LeftPPP
PIP-Top Left
PPP
PIP-Top Right
PPP  
						

							— 35 — 
DLP Projector — Owner’s Manual
Setup Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select SETUP and press 
the Enter button to enter the SETUP menu. Press the arrow keys (pq) to select the menu option and 
press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust the 
desired settings and press the Enter button to confirm.
PICTUREOUTPUT SETUP
OPTIONSETUP
English AutoOff
Language
Ceiling Mount
Rear Projection
Lens Function
Menu Preferences
Pin
Communications
ItemDescrIptIon
LanguageThis item allows you to select an available language for the OSD display\
.
Ceiling MountTurn the image upside down for ceiling-mounted projection.
Rear ProjectionReverse the image so you can project from behind a translucent screen.
Lens FunctionConfigure the lens function settings. See “Lens Function Menu” on page 
35.
Menu PreferencesConfigure the menu preferences settings. See “Menu Preferences Menu” 
on page 36.
PinConfigure the pin settings. See “Pin Menu” on page 37.
CommunicationsConfigure the communications settings. See “Communications Menu” on 
page 38.
Lens Function Menu
Press the Menu button to open the OSD menu. Press the arrow keys (pq) to select SETUP and press 
the Enter button to enter the SETUP menu. Press the arrow keys (pq) to select Lens Function and 
press the Enter button to enter the Lens Function menu. Press the arrow keys (pq) to select the menu 
option and press the Enter button to enter its submenu. Press the arrow keys (pqtu) to select or adjust 
the desired settings and press the Enter button to confirm.