Eiki Projector EK-502XL User Manual

31
Adjustment pad
Keystone adjustment
Adjustable pad
You may use the adjustment leg to raise your pro
-
jector up to 5.0 degree.
Turn the pad to tilt your projector to required height. 
To raise your projector, turn both pads clockwise.
To lower down your projector or close the pad, turn 
both pads counterclockwise.
You may use the auto setup function to adjust your 
projector’s keystone distortion automatically or do 
this with the remote controller or OSD menu manu -
ally.
You may adjust keystone...

32
Menu item overview
Main menuSubmenu设置PC adjust
Auto PC adj.
Fine sync                                                          16
Total dots                                                            0
Horizontal                                                           0
Vertical                                                                0\
Clamp                                                                 1
Display area H                                                    0
Display area V...

33
Main menu Submenu设置PC adjust
Auto PC adj.
Fine sync                                                          16
Total dots                                                            0
Horizontal                                                           0
Vertical                                                                0\
Clamp                                                                 1
Display area H                                                    0
Display area V...

34
Remote controller operation
Use your remote controller for common operations.
Screen size selection (SCREEN)
Press the SCREEN button on remote controller 
to select required screen size mode.
Digital Zoom (D.ZOOM+/-)
Press the D.ZOOM+/- button on remote con-
troller to enter the Digital Zoom mode. 
*Only for input as VGA, RGBHV, and the 
screen size setting as Normal or Wide. 
Volume +/- (VOLUME +/-)
Increase or decrease volume. 
Timer (TIMER)
Press the TIMER button on remote controller. 
A timer...

35
Input source (Computer signals)
Basic operation
Press the INPUT button on the control panel to select one of the following input: VGA, RGBHV, 
HDMI or DVI. Alternatively, you may press the VGA, RGBHV, HDMI, DVI button on remote control-
ler to select individual source directly. 
Menu operation
1  Press the MENU button on remote controller and the OSD displays. Press 
 button, select the 
input icon, press  button or OK button to enter the Input menu.
2 Press 
 button, select VGA, RGBHV, HDMI or DVI,...

36
VGA 1
RGBHV
HDMI
DVI
Select input VGA if a PC is connected to 
the VGA IN port with a VGA cable.
Select input HDMI if a device is connected to 
the HDMI terminal with a HDMI cable.
Select input DVI if a device is connected to the 
DVI terminal with a DVI cable. Select input RGBHV if a PC is connected to 
the BNC terminal with a 5 BNC cable.
Input source (Computer signals)
Input source selection (VGA / RGBHV)
Input source selection (HDMI / DVI)
 Note: 
If the Input Search option in the Auto Setup...

37
Input source (Computer signals)
System selection
The scanning system and auto computer adjustment function may detect scores of signal format.   
If a PC is selected as the input signal source, your projector will detect and adapt to its signal for-
mat automatically. Correct image can be displayed without any setup operation. 
Your projector will display one of the following: Auto
-----
If your projector failed to identify 
signals not shown in the signals 
format table, the “Auto” message 
will...

38
Input source (Computer signals)
Auto  PC Adjusting
The Auto PC Adjusting function may get Total Dots, Horizontal and Vertical position, Display area H, 
and Display area V aligned with computer input. Auto  PC Adjusting
1  Press the MENU button on remote controller 
and the OSD displays. Press 
 button to 
select PC adjustment icon. Press  button or 
OK button and the PC adjust menu displays. 
2 Press 
 button to point to Auto PC Adj. op-
tion, press OK button to confirm your choice. 
 Note: 
 
●...

39
Manual computer adjustment
The scan system of your projector may fail to detect signal format used \
by certain computers as 
they opted some special signal format. The manual computer adjustment function of your projector 
enables you to adjust individual parameter to align with most special si\
gnal format. Your projector 
comes with up to storage area to keep parameters manually adjusted by yo\
u. You may save pre-
ferred settings for certain computers as required. 
1  Press MENU button on the...

40
Image mode selection 
Direct operation 
Press the Image Select button on remote controller to select required im\
age mode. 
Menu operation
1  Press the MENU button on remote controller and the OSD displays. Press  button select 
image select icon , press  button or OK button to confirm your selection. 
2 Press  button to point to required item and press OK button to confirm your selection.
Dynamic
An image mode suitable for viewing in bright 
room. 
Normal
The default mode of your projector. 
Cinema...