Eiki Projector EK-502X User Manual

21
Remove the lens
1 Center the lens with its movement func -
tion. (Hold 5 sec. on Lens Shift button. 
Refer to the Page 30).
2  Power off your projector and unplug the 
AC power cord. 
3  Turn it counterclockwise and remove its 
decoration ring. 
4  Press and hold the lens release button 
at top of the casing. Turn it counterclock -
wise until it sticks, and then pull it out of 
your projector gently. 
Installing lens
1  Turn the lens counterclockwise and 
remove its decoration ring. 
2  Align the red...

22
The projection location of your image may be 
moved upward a distance up to 70%(WXGA) 
/ 60%(XGA) of the length of the image. Move lens to it top 
position
The projection location of your image may 
be moved downward a distance up to 
70%(WXGA) / 60%(XGA) of the length of the 
image.Move lens to it 
bottom position
The projection location of your image may be 
moved leftward a distance up to 30% of the 
width of the image.
Move lens to it 
leftmost position
The projection location of your image may be...

23
300"
200"
150"
100"
30"
Set up your projector
●  Ambient brightness may affect your projection image quality. For the optimal image effect, it is 
recommended to control brightness in your environment.      
●  Values shown in figure below are approximates only. They may differ from the actual ones.    
Installation
EK-501W(16:10) Unit:cm
Lens Model No.AH-E22010AH-E22020 AH-E21010AH-E23010AH-E23020
Screen size WidthHeight Distance WideTeleWide TeleWide TeleWide Tele
30 inch  6440...

24
Precautions on power cord  
Your AC power cord should meet regulations of the country/district where your\
 projector is 
used. 
Please make sure the type of the power plug is compliant with those given in figure below. 
Make sure you are using a valid AC power cord.
In case the included AC power cord does not comply with the AC power socket in your loca -
tion, call your dealer for replacement.
The projector side Connect to the AC power socket
Connect to power cord connector of  your projector...

25
Cables for connection: 
● VGA cable● DVI cable*
● BNC cable* ● HDMI cable*
(* This cable is optional. )
Cables for connection: 
● S-VIDEO cable* ● VIDEO cable*
● BNC cable*
(* This cable is optional.)
Connection to computer
Connect to video equipment
Unplug power cords of your projector and all external equipment before c\
onnecting 
any cable to them.
Connection to equipment
Ports on your projector  Connection cableEquipment 
DVI-D(HDCP)
VOL-VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C...

26
Cables for connection: ● Audio cable*  
(* This cable is optional.) 
Connection to audio equipment
Unplug power cords of your projector and all external equipment before c\
onnecting 
any cable to them.
Connection to equipment
Ports on your projector Connection cable Equipment 
MONO L/R
VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
IN
G/Y
B/PBH/HV V
Audio cable
AUDIO IN
VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN...

Operation
This chapter introduces you to basic 
operation of your projector.  

28
Basic operation
Power on your projector
1. Connect all external equipment to your projector (e.g. computer or camera) before powering it on.
2.  Connect AC power cord of your projector to an AC power socket. The Power indicator turns on in 
red.  
3.  Press the Power button on the rear control panel or the remote controller.  
The Power indicator lights in green and the cooling fan starts running.
4.  If your projector is setting as password protected, the password dialog box displays. Enter your...

29
Power off your projector 
Power Power  
360.2
141.7VOL-
VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
ING/Y
B/PBH/HV V
1. Press the Power button at the rear control 
panel or the remote controller, the “Power 
off?” message displays.
2.  Press the Power button again in 4 seconds 
after the “Power off?” message prompted 
to you. The POWER indicator flashes red 
while the cooling fan continues running. 
(You may set up noise level and speed of...

30
Zoom /focus function
1. Press the ZOOM / FOCUS button on the 
rear control panel or remote controller for 
zooming and focusing.
2.  Press 
 button to zoom in and out.  
Press  button to change focus of 
image. Default adjustment speed is set to 
FAST. You may press the ENTER button, 
select STEP for speed fine-tuning. 
Lens movement adjustment
1.  Press the LENS SHIFT on the rear control 
panel or remote controller to adjust posi -
tion of the lens. Default adjustment speed 
is set to FAST. You may...