Eiki Projector Eip X200 User Manual

EN-10
Rear View
 1Rear IR remote control sensor
 2Ventilation holes
 3Terminals
 4Elevator button
 5 Elevator foot
 6 Speaker
 7 AC power socket
 8 Kensington lock
1232
65478
1
2
2
2
This projector can be used with a ceiling mount for support. The ceiling
mount is not included in the package.
Bottom View
 1 Lamp cover
 2 Ceiling mount 

EN-11
Using the Product
Control Panel
LED
 1Lamp LED indicator
Refer to “LED Indicator Messages”. (p.30)
 2 Power LED indicator
Refer to “LED Indicator Messages”. (p.30)
Button Function
  3 Power
Refer to “Powering On/Off the Projector”.
  4 Keystone 
SS SS
S /
TT
TT
T
Adjusts image distortion caused by tilting the projector.
  5 Auto 
XX
XX
X
Automatically adjusts frequency, total dots. This function is available \
for computer
mode only.
 6 Menu
Displays or exits the on-screen display menus.
  7 Source...

EN-12
Ter minals
 1SERIAL
When operating the projector via a computer, connect this to the control\
ling
computer’s RS-232C port.
 2  USB(COMPUTER)
This connector is for firmware update.
 3 COMPUTER  IN
Connects image input signal  (analog) to this jack.
 4 S-VIDEO
Connects S-V ideo output from video equipment to this jack.
 5 VIDEO
Connects  composite video output from video equipment to this jack.
 6 AUDIO IN
Connects an audio  output from video equipment to this jack.
235641 

EN-13
Remote Control
 1Power
Refer to “Powering On/Off the
Projector”. (p. 17)
 2 Four directional buttons
Use four directional buttons to select
items or make adjustments to your
selection. (p. 22)
  3 Menu
Displays or exits the on-screen display
menus. (p. 22)
  4 Enter
To select the desired setting. (p. 25)
  5 Keystone  c /d
Adjusts image distortion caused by tilting
the projector. (p. 11, 23)
 6 Volume  c /d
Press the Volume  c button to increase
the volume
press the Volume  d button
to reduce the...

EN-14
For the first time use:
Remove the transparent insulation tape by pulling it
before use.
For batter y change:
1. Push the catch to the right and remove thebattery holder.
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the
mark “+” is up.
3. Push the battery holder back into the remote control until you feel a click.
Keep the battery out of the reach of children. There is a danger of death
by accidentally swallowing the battery.
Do not recharge the used...

EN-15
Remote Control Operation
Point the remote control at the infrared remote sensor and press a butto\
n.
  Operating the projector from the front
   Operating the projector from the rear
The remote control may not operate when there is sunlight or other
strong light such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is
visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively...

EN-16
Desktop type
Laptop type
23
75
1
46
When connecting cable, power cords of both a projector and external
equipment should be disconnected from AC outlet.
The figure above is a sample connection. This does not mean that all of
these devices can or must be connected simultaneously.
The cables that come with the projector may differ from the above
illustration. The included cables are based on actual shipment delivery.
Installation
Connecting the Projector
 
1 RS232 Cable 5Composite Video Cable
  2 USB...

EN-17
Powering On/Off the Projector
Powering on the projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. The Power LED blinks Green in standby mode.
4. Press 
 button on the control panel or remote control to turn on the projector.\
 The
Power LED lights on Amber and Lamp LED lights on Green when the lamp is on.
5. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
JWhen searching...

EN-18
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image heig\
ht.
To raise the image:
1. Press the elevator button.
2. Raise the image to the desired height angle, then release the button to lock theelevator foot into position.
To lower the image:
1. Press the elevator button.
2. Lower the image, then release the button to lock the elevator foot into position.
To avoid damaging the projector, make sure that the elevator foot...

EN-19
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image by rotating the zoom ring. Rotate to the right to reduc\
e the image.Rotate to the left to enlarge the image.
Focus ringZoom ring