Eiki Projector Eip 5000 User Manual

							9
Ensure that you read the following safeguards when
setting up your projector.
Caution concerning the lamp unit
■Potential hazard of glass particles if lamp rup-
tures. In case of lamp rupture, contact your
nearest EIKI Authorized Dealer or Service
Center for replacement.  See “Replacing the
Lamp” on page  96.
Caution concerning the setup of the pro-
jector
■ For minimal servicing and to maintain high
image quality, EIKI recommends that this pro-
jector be installed in an area free from hu-
midity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more
often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by an EIKI Authorized Dealer or Service Cen-
ter.
Do not set up the projector in places ex-
posed to direct sunlight or bright light.
■Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
The projector may be safely tilted to a
maximum angle of 9 degrees.
■Placement should be within 9 degrees of
horizontal.
If you have application requiring tilt angle
exceeding 9 degrees, please check with your
local EIKI sales office.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in a
high position
■When placing the projector in a high posi-
tion, make certain it is carefully secured to
avoid personal injury caused by the projec-
tor falling down.
Do not subject the projector to hard im-
pact and/or vibration.
■Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of tem-
perature.
■The operating temperature of the projector
is from 41°F to 104°F (+5°C to +40°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
9° 
						

							10
Using the projector in other countries
■The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■If the projector starts to over-
heat due to setup problems or
blockage of the air vents, “
”
and “
”  will illuminate in
the lower left corner of the picture. If the tem-
perature continues to rise, the lamp will turn off,
the temperature warning indicator on the pro-
jector will blink, and after a 90-second cooling-
off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on
page  94 for details.
Info
•The cooling fan regulates the internal tem-
perature, and its performance is automati-
cally controlled. The sound of the fan may
change during projector operation due to
changes in the fan speed. This does not
indicate malfunction.
• Even if you unplug the power cord after
projector operation, the cooling fan con-
tinues to run for a while. When you place
the projector into the storage case, make
sure that the cooling fan has stopped.
Optional lens installation
■ Be sure to have service personnel install the
optional lenses.
Do not block the intake and exhaust
vents.
■Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Be sure that the intake vents and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion (See pages  94 and  95.). Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
Caution regarding usage of the projector
■ When  using the projector,  take care not to sub-
ject it to hard impact and/or vibration, as this
can result in damage. Take extra care with the
lens. If  you are not to use  the projector for a
long time, make certain you  unplug the power
cord from the wall outlet, and disconnect any
other cables connected to it.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure you at-
tach the lens cap to the projector. (See page
13.)
■ Do not expose the projector to direct sunlight
or place it near heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
Other connected equipment
■When connecting a computer or other audio-
visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the owner’s manuals of the pro-
jector and the equipment to be connected for
instructions on how to make the connections.
IMPORTANT SAFEGUARDS 
						

							11
Accessories
Two R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Power cord
*
For U.S., Canada, etc.
(6 (1.8 m))
9NK3090204900 For Europe, except U.K.
(6 (1.8 m))
9NK3090152700
* Use the power cord that corresponds to the wall outlet in your country.(1)
(2)
Remote mouse receiver
(53 (1.6 m))
9NK3790199300 Cap for the standard zoom lens
(Only supplied with EIP-5000)
Supplied accessories
RGB cable
(10 (3.0 m))
9NK3080431000
Owner’s manual (this manual)
Remote control
■ Lamp
Lamp unit 1 AH-50001
Lamp unit 2 AH-50002
Optional accessories
Projector manual and
technical reference
CD-ROM QUICK GUIDE 
						

							12
Accessories
■Lens Projection distance for 100 screen size
Fixed wide lens ( × 0.8) AH-45201 54 (1.6 m)
Wide-zoom lens ( × 1.5 – 1.8) AH-45301 10 – 12 (3.0 m – 3.7 m)
Standard zoom lens ( × 1.8 – 2.2) AH-51401 12 – 148 (3.7 m – 4.5 m)
(Standard equipment with EIP-5000)
Tele-zoom lens ( × 2.25 – 3.00) AH-45501 15 – 20 (4.6 m – 6.1 m)
Tele-zoom lens ( × 3.0 – 4.5) AH-45601 20 – 30 (6.1 m – 9.1 m)
Tele-zoom lens ( × 4.5 –7.0) AH-45701 30 – 468 (9.1 m – 14.2 m)
Optional lenses
No lens is attached to EIP-5000L. The standard zoom lens is attached to \
EIP-5000.
The optional lenses from EIKI are also available for specialized applica\
tion. Please see your
nearest EIKI Authorized Dealer for details on all the lenses. (Refer to the lens own\
er’s manual
when using a lens.) Also, be sure to have service personnel install the optional lenses.
Throw Distance
The graph below is for 100 inches (254 cm) screen with 4:3 normal mode\
.
Screen
5 101520253035 4550 40 (ft)
Standard zoom lens (AH-51401 : Standard equipment with EIP-5000)
12–148 (3.7 m–4.5 m)
Throw distance ratio 1:1.8–2.2
Fixed wide lens (AH-45201)
54 (1.6 m)
Throw distance ratio 1:0.8
Tele-zoom lens (AH-45501) 15–20 (4.6 m–6.1 m)
Throw distance ratio 1:2.25–3.00
Tele-zoom lens (AH-45601) 20–30 (6.1 m–9.1 m)
Throw distance ratio 1:3.0–4.5
Tele-zoom lens (AH-45701)30–468 (9.1 m–14.2 m)
Throw distance ratio 1:4.5–7.0
Wide-zoom lens (AH-45301) 10–12 (3.0 m–3.7 m)
Throw distance ratio 1:1.5–1.8 
						

							13
37
45
70
40
40
73
39
41
56
39
56
56
56
46
17
45
14
14·94
14·94
14·94
97
93
ENTER button
For setting items selected or adjusted on the menu.
KEYSTONE button
For entering the Keystone  Correction mode.
Carrying handle
For carrying theprojector. 
STANDBY-ON button
For turning the power on or  putting the projector into standby mode.
Adjustment buttons  (' /" /\ /| )
For selecting menu items 
and other settings.
ZOOM button
For adjusting the projected  image size.
FOCUS button
For adjusting the focus.
39
Power indicator
MENU button
For displaying adjustment 
and setting screens.
UNDO button
For undoing an operation 
or returning to the previous 
display.
AUTO SYNC button
For automatically 
adjusting images when 
connected to a computer.
INPUT 1, 2, 3 button
For switching input mode 
1, 2 or 3. 
INPUT 4, 5 button
For switching input mode 
4 or 5. 
Volume buttons
For adjusting the speaker 
sound level.
Temperature warning 
indicator
Lamp indicator 2 Lamp indicator 1
Remote control  sensor
Speaker
Adjustment foot 
(on the bottom of  the projector)
93Intake vent Adjustment foot 
(on the bottom of 
the projector)
Lamp unit cover
Intake vent 
73Speaker
H & V LENS SHIFT button
For shifting the lens horizontally 
and vertically.
Projector
Part Names and Functions
•Attaching the lens cap
Push the lens cap on until it clicks
into position.
• Removing the lens cap
Pull the lens cap directly outward.
Numbers in  refer to the main pages  in this owner’s m anual where the topic is explained.
Top View
Front View 
						

							14
About the Indicators on the Projector
Power indicator
Green on ...
 Normal (Standby)
Red on  ...
 Normal (Power on)
Green blinks  ...
 The intake vent cover is open. 
(See page  93.)
Temperature warning indicator
Off  ...
 Normal
Red blinks/on  ...
The internal temperature is abnormally
high. (See pages  94 and  95.)
Lamp indicators 1, 2
Green on  ...
 Normal
Green blinks  ...
 
The lamp is warming up.
Red on  ...
 The lamp has been shut down abnormally or 
needs to be changed. (See pages  94 and  95.)
Part Names and Functions 
						

							15
Projector (Side View)
Using the Kensington Lock
•This projector has a Kensington Security Standard connector for use with\
 a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructi\
ons on how to use it to secure the
projector.
Numbers in  refer to the main pages  in this owner’s m anual where the topic is explained.
INPUT 1 terminal
Terminal for computer RGB 
and component signals.
AUDIO input (1) terminal
Audio input terminal for  INPUT 1.
INPUT 2 terminals
BNC terminals for computer RGB and component  signals.
INPUT 4 terminal
Terminal for connecting video equipment.
INPUT 5 terminal
Terminal for connecting 
video equipment with an  S-video terminal.
AUDIO input (4, 5) terminals
Shared audio input terminals for  INPUT 4 and 5.
RS-232C terminal
Terminal for controlling the 
projector using a computer.
WIRED REMOTE terminal
For connecting the remote 
control to the projector when  the signals from the remote  control cannot reach the remote control sensor.
INPUT 3 terminal
Terminal for DVI digital RGB 
and digital component signals.
OUTPUT (FOR INPUT 1, 2) 
terminal
Output terminal for computer 
RGB and component signals. 
Shared for INPUT 1 and 2.
AUDIO input (2, 3) terminal
Shared audio input terminal for 
INPUT 2 and 3.
AUDIO OUTPUT terminal
Audio output terminal shared 
for INPUT 1–5.
Remote control sensor
Exhaust vent
The speed and pitch of 
the cooling fan may 
change during operation 
in response to internal 
temperature changes. 
This is normal operation 
and does not indicate a 
malfunction.
AC socket
Connect the supplied power 
cord.
Kensington Security 
Standard connector LAN terminal
Terminal for controlling the 
projector using a computer 
via network.
37
17
93
35
29
36
28
36
27
27
28
35
34
18
34
34
TerminalsRefer to “INPUT/OUTPUT Terminals and Connectable Main Equipment” on
page 
24. 
						

							16
Note
•All the buttons on the remote control, except the mouse/adjustment butto\
n and the ADJ./MOUSE switch,
are made of luminous material that is visible in the dark. Visibility will diminish over time. Exposure to
light will recharge the luminous buttons.
Remote Control
4018
56
39
40
45
70
18
48
37
47
19
41
46
50
46
46
50
47
STANDBY-ON button
For turning the power on or putting 
the projector into standby mode.
ZOOM buttons
For adjusting the projected  image size.
KEYSTONE button
For entering the Keystone Correction mode.
ENLARGE (enlarge/reduce)  buttons
For enlarging/reducing part of the 
image.
INPUT 1, 2, 3, 4 and 5 buttons
For switching to the respective input modes.
AUTO SYNC button
For automatically adjusting images when connected to a computer.
BREAK TIMER  button 
For setting the break time. 
L-click button
For the left click while the 
ADJ./MOUSE switch is the  MOUSE position. 
FOCUS buttons
For bringing the projected image  into focus.
Mouse/adjustment button 
(' /" /\ /| )
For moving the computer 
cursor while the 
ADJ./MOUSE switch is the 
MOUSE position.
 For selecting menu items 
while the ADJ./MOUSE 
switch is the ADJ. position. 
ENTER button
For setting items selected or 
adjusted on the menu.
FREEZE button
For freezing images.
RESIZE button
For switching the screen size.
BLACK SCREEN button
For temporarily displaying the black 
screen.
 
PICTURE MODE button
For switching the picture mode.
WIRED R/C JACK
For connecting the remote control 
to the projector when the signals 
from the remote control cannot 
reach the remote control sensor.
Volume buttons
For adjusting the speaker sound level.
MUTE button
For temporarily turning off the 
sound.
R-click/UNDO button
 For the right click while the 
ADJ./MOUSE switch is the 
MOUSE position.
 For undoing an operation or 
returning to the previous 
display while the ADJ./MOUSE 
switch is the ADJ. position.
MENU button
For displaying adjustment and 
setting screens.
ADJ./MOUSE switch
For switching the remote control 
modes.
H & V LENS SHIFT button
For shifting the lens horizontally 
and vertically.
19·56
19·56
Numbers in  refer to the main pages  in this owner’s m anual where the topic is explained.
Part Names and Functions 
						

							17
Using the Remote Control
Inserting the Batteries
1Press the tab and lift open the battery
cover in the direction of the arrow
.
2Insert the batteries.
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may cause them to leak or explode. Please\
 follow the precautions below.
 Caution
• Danger of explosion if battery is incorrectly replaced. Replace only wit\
h the same or equivalent type.
• Insert the batteries making sure the polarities correctly match the 
 and  marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to\
 leak.
• Remove the batteries from the remote control once they have run out, as \
leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure\
 that you first wipe them and then remove
them using a cloth.
• The batteries included with this projector may run down in a short perio\
d, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using th\
e remote control for a long time.
• Comply with the rules (ordinance) of each local government when dispos\
ing of worn-out batteries.
Usable Range
The remote control can be used to control
the projector within the ranges shown in the
illustration.
Note
•The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
When using the remote control:
•Ensure that you do not drop it or expose it to
moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
Front View
Rear View
Remote control
signal transmitters Remote control sensor
Remote control
30 °
30 °
30°23 (7 m)
30°
30°
30
°23 (7 m) Remote control sensor
Remote control
signal transmitters
Remote control 
						

							18
Using the Remote Control
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the po\
sitioning of the projector, use a
ø3.5 mm minijack cable to connect the remote control to the projector\
. Now you can control the projector
with the remote control.
Note
•The wireless remote function is not possible when the ø3.5 mm minijac\
k cable is connected to the projec-
tor. Should the wireless remote operation be required, the ø3.5 mm minij\
ack cable should be discon-
nected from the projector.
Switching the Remote Control Mode
The remote control has two functions. One is projector control and the o\
ther is wireless computer mouse.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the \
desired usage.
Info
•When using the remote control as the wireless computer mouse, connect th\
e supplied remote mouse
receiver to the computer. (See page  19.)
Side viewRemote control
To WIRED R/C JACK
To WIRED REMOTE terminal
ø3.5 mm minijack cable (commercially available)
ADJ.
MOUSEADJ.
MOUSE
Projector control Wireless computer mouse