Eiki Lc-Xt5 Multimedia Projector Owners Manual
Have a look at the manual Eiki Lc-Xt5 Multimedia Projector Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
71 When an input signal is digital from the DVI terminal, refer to the chart below. Appendix ✔Note: • Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed. • Specifications are subject to change without notice. ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz) D-VGA640x48031.470 59.940 D-480p720x48031.470 59.880 D-575p720x57531.250 50.000 D-SVGA800x60037.879 60.320 D-XGA1024x76843.363 60.000 D-WXGA 11366x76848.360 60.000 D-WXGA 21360x76847.700 60.000 D-WXGA 31376x76848.360 60.000 D-WXGA 41360x76856.160 72.000 D-WXGA 51366x76846.500 50.000 D-WXGA 61280x76847.776 59.870 D-WXGA 71280x76860.289 74.893 D-WXGA 81280x76868.633 84.837 D-WXGA 91280x80049.600 60.050 D-WXGA 101280x80041.200 50.000 ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz) D-SXGA 11280x102463.980 60.020 D-SXGA 21280x102460.276 58.069 D-SXGA+ 11400x105063.970 60.190 D-SXGA+ 21400x105065.350 60.120 D-SXGA+ 31400x105065.120 59.900 D-720p1280x72045.000 60.000 D-720p1280x72037.500 50.000 D-1035i1920x1035 (Interlace)33.750 60.000 D-1080i 1920x1080 (Interlace)33.750 60.000 1920x1080 (Interlace)28.125 50.000 D-1080psf/301920x108033.750 60.000 D-1080psf/251920x108028.125 50.000 D-1080psf/241920x108027.000 48.000
7
Technical Specifications
Mechanical Information
Projector Type Multi-media Projector
Dimensions (W x H x D) 22.87” x 9.902” x 32.11” (581 mm x 251.5 mm x 815.5 mm) (Not including adjustable feet)
Net Weight 80.3 lbs (36.5 kg)
Feet Adjustment 0˚ to 5.7˚
Panel Resolution
LCD Panel System 1.8” TFT Active Matrix type, 3 panels
Panel Resolution 1,024 x 768 dots
Number of Pixels 2,359,296 (1,024 x 768 x 3 panels)
Signal Compatibility
Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
High Definition TV Signal 480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
Scanning Frequency H-sync. 15 kHz–120 kHz, V-sync. 48 Hz–120 Hz
Optical Information
Projection Lamp 330 W NSHA lamp x 4
Interface
Input 1 DVI-D Terminal (Digital), D-Sub 15-pin Terminal (Analog)
Input 2 BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), S-Video
Other Jacks Serial port in (D-sub 9), Serial port out (D-sub 9), USB port, and \
Wired Remote Jack
Power
Voltage and Power Consumption AC 240 V (9.7A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200–240 V (9.7A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
Operating Environment
Operating Temperature 41˚F–95˚F (5˚C–35˚C)
Storage Temperature 14˚F–140˚F (-10˚C–60˚C)
Remote Control
Battery AA or LR6 Type x 2
Operating Range 16.4’ (5 m/±30˚)
Dimensions 1.97” (W) x 1.06” (H) x 6.61” (D) (50 mm x 27 mm x 168 mm)
Net Weight 4.6 oz (129 g) (including batteries)
Accessories
Owner’s Manual (CD-ROM)
Quick Reference Guide
AC Power Cord
Remote Control and Batteries
VGA cable
Remote Control Cable
PIN Code Label
Lens Attachments (2 types) (For option lens)
Light Block Plates (3 types) (For option lens)
Spacer (For option lens)
Real Color Manager Pro (CD-ROM)
Appendix
7
Optional Parts
Model No.
Option Slot Board (DVI)
: AH-72003
Option Slot Board (5-BNC)
: AH-72015
Option Slot Board (D-sub 15)
: AH-72031
Option Slot Board (Dual-SDI)
: AH-72162
Option Slot Board (Network board)
: AH-72142
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No.
to the sales dealer.
Appendix
● The specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny
fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
● Each projector has its own characteristics.
When projecting with several projectors on the same screen or side by side, you may recognize different white balance
and color uniformity on each projector.
74 Configurations of Terminals ANALOG (Mini D-sub 15 pin) 512341096781514131112 Red Input Ground (Horiz.sync.) Green Input Sense 2 Blue Input Ground (Red) Ground (Green) Ground (Blue) 1 5 4 6 7 +5V Power Horiz. sync. Ground (Vert. sync.) DDC Data Sense 0 Vert. sync. DDC Clock 9 1 10 1 11 14 15 CONTROL PORT CONNECTOR (D-sub 9 pin) ----- R X D T X D ----- SG ----- RTS CTS Serial 1 4 5 6 7 DIGITAL DVI-D (DVI 4 PIN) 1917 21018 31119 41220 51321 61422 71523 81624 T.M.D.S. Data2– No Connect T.M.D.S. Data2+ No Connect T.M.D.S. Data2 Shield DDC Clock DDC Data No Connect 1 5 4 6 7 T.M.D.S. Data1– No Connect T.M.D.S. Data1+ No Connect T.M.D.S. Data1 Shield +5V Power Ground (for +5V) Hot Plug Detect 9 1 10 1 11 14 15 16 T.M.D.S. Data0– No Connect T.M.D.S. Data0+ No Connect T.M.D.S. Data0 Shield T.M.D.S. Clock Shield T.M.D.S. Clock+ T.M.D.S. Clock– 17 1 1 0 19 4 Vcc - Data + Data Ground 1 4 USB CONNECTOR (Series B) 2 3 4 1 Appendix -----9
75 Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. Factory default set No: 1 2 3 4* Factory default set No: 4 3 2 1* * S h o u l d t h e fo u r- d i g i t n u m b e r b e changed, the factory set number will be invalid. Put the label below (supplied) on in a prominent place of the projector’s body while it is locked with a PIN code. While the projector is locked with the PIN code... PIN Code Lock No. Logo PIN Code Lock No. PIN Code Number Memo Appendix
76 Dimensions Appendix 161° 14.74 (374.5) 1.38 (35) 10.61 (269.5) 7.01 (178)7.01 (178) 8.27 (210) 1.57 (40) 8.27 (210)3.66 (93) 22.93 (582.5) 17.56 (446) 3.26 (82.8) 9.72 (247) 9.9 (251.5)2.36 (60) 5.7° 9.90 (251.5) 20.58 (522.7) 1.28 (32.5) 9.90 (251.5) 5.18 (131.5) 22.87 (581) 32.11 (815.5) 6.81 (173) Unit : inch (mm) Appendix
77
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial
port.
Connect a RS-232C serial cross cable to SERIAL
PORT IN on the projector and serial port on the PC.
(See p.11)
Launch a communication software provided with PC
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check : none
Stop bit : 1
Flow control : none
Data bit : 8
Type the command for controlling the projector and
then enter the "Enter" key.
Example
When you want to change the input to INPUT 2,
Type 'C' '0' '6' 'Enter'.
✔Note:
• The default of the baud rate is set to 19200
bps. If an error occurs in the communication,
change the serial port and the communication
speed (baud rate).
• Enter with ASCII 64-byte capital characters
and one-byte characters.
The command is sent from PC to the projector with
the format below;
'C' [Command] 'CR'
Command: two charactors (refer to the
command table below.
-The projector decodes the command and returns the
'ACK' with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it
returns with format below.
‘?’ ‘CR’
Format
Operation
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector OFF
(immediately OFF)
C05Select Input 1
C06Select Input 2
C07Select Input 3
C08Select Input 4
C0DVideo mute ON
C0EVideo mute OFF
C0FAspect 4:3
C10Aspect 16:9
C1CMenu ON
C1DMenu OFF
C3APointer RIGHT
CommandFunction
C3BPointer LEFT
C3CPointer UP
C3DPointer DOWN
C3FEnter
C46Zoom DOWN
C47Zoom UP
C4AFocus DOWN
C4BFocus UP
C5DLens shift UP
C5ELens shift DOWN
C5FLens shift LEFT
C60Lens shift RIGHT
C89Auto PC Adj.
C8EKeystone UP
C8FKeystone DOWN
C90Keystone RIGHT
C91Keystone LEFT
7
Status Read Command
Appendix
The command is sent from PC to the projector with
the format below;
'CR' [Command] 'CR'
Command: one character (refer to the command
table below.
The projector decodes the command and returns the
'Charactor string' with the format below;
Format
CommandFunctionProjector
ReturnProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly
02Unable to receive the RC232C command.
24Cooling down at Power Management mode
04Power Management mode after Cooling down
21Cooling down after the projector is turned off when the lamps
are out.
81Stand-by mode after Cooling down when the lamps are out.
88Stand-by mode after Cooling down at the temperature
anomaly.
CR6Temperature ReadS1 S2 S3
S1 = Temperature at Sensor 1 (˚C)
S2 = Temperature at Sensor 2 (˚C)
S3 = Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C, S2 = 23.4˚C, S3 = 34.5˚C
--> The projector displays “12.3 23.4 34.5”
( For each sensor, two digit and the tenth place numbers are
displayed with a space between each temperature.)
?Communication failure
The tables on page 77 and 78 show the typical command lists for controlling the projector. Please consult your
local dealer for further information of other commands.
U .S .A . EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. Tel : 800-242-3454 (949)-457-0200 Fax : 800-457-3454 (949)-457-7878 E-Mail : [email protected] Deutschland & Österreich EIKI Deutschland GmbH Am Frauwald 12 65510 Idstein Deutschland Tel : 06126-9371-0 Fax : 06126-9371-14 E-Mail : [email protected] Canada EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800-563-3454 (705)-527-4084 Fax : 800-567-4069 (705)-527-4087 E-Mail : [email protected] Eastern Europe EIKI CZECH spol. s.r.o. Umelecká 15 170 00 Praha 7 Czech Republic Tel : +42 02 20570024 +42 02 20571413 Fax : +42 02 20571411 E-Mail : [email protected] ˆ Japan & Worldwide EIKI Industrial Company Limited. 4-12 Banzai-Cho, Kita-Ku, Osaka, 530-0028 Japan Tel : +81-6-6311-9479 Fax : +81-6-6311-8486 WorldWide Website http://www .eiki .com KE3B© 2007 Eiki International, Inc. China EIKI (Shanghai) Co.,LTD 1. Dapu Road, Golden Magnolia Plaza #2109 Shanghai, 200023 China Tel : 86-21-5396-0088 Fax : 86-21-5396-0318 E-Mail : [email protected]