Eiki Lc-Xl200l Multimedia Projector Owners Manual

							
1

Remote	Control
POINT	▲▼◄►buttons
KEySTONE	button
Basic	Operation
If a projected picture still has keystone distortion after pressing 
the AUTO PC button on the remote control, correct the image 
manually as follows:
Press the KEYSTONE button on the remote control to switch the 
Standard (for Vertical/Horizontal) /Corner correction adjustment. 
The Standard or Corner correction adjustment dialog box appears. 
Use the Point ▲▼◄► buttons to correct the Standard or Corner 
distortion. The Standard or Corner correction adjustment can be 
stored (see pages 44, 50).
Note:
•	The	white	arrows	indicate	that	there	is	no	correction.
•	A	red	arrow	indicates	the	direction	of	correction.
•	An	arrow	disappears	at	the	maximum	correction.
•	If	you	press	and	hold	the	KEYSTONE	button	for
		more	than	3	seconds	while	the	Standard	or	Corner	 correction	dialog	box	is	being	displayed,	the	
Standard	or	Corner	correction	adjustment	will	be	
released.
•	The	 Corner	 pattern	 can	be	set	 to	Off,	Red ,	White 	or	
Blue 	in	 the	 Corner	 pattern	 function.	 See	"Keystone"	
on	pages	44,	50.
•	The 	adjustable 	range 	is 	limited 	depending 	on 	the	
input	signal.	
•	Standard	and	Corner	correction	functions	cannot	 be	adjusted	at	the	same	time.	If	one	of	the	fuctions	
is	adjusted,	and	then	the	other	one	will	be	reset	
automatically. Reduce the top left corner part with the Point ►▼ buttons. 
Keystone
Reduce the top right corner part with the Point ◄▼ buttons.  
KeystoneKeystone
Keystone
Reduce the bottom left corner part with the Point ►▲ buttons. Reduce the bottom right corner part with the Point ◄▲ buttons.  
Press the KEYSTONE button on the remote control to switch 
Corner correction adjustment, press the SELECT button on the 
remote control to select the corner you want to adjust. 
Reduce the right part with Point ► button.  
Reduce the upper width with the Point ▲ button. 
Reduce the left part with Point ◄ button.  
Reduce the lower width with the Point ▼ button.  
Press the SELECT button 
Press the SELECT button 
Press the SELECT button 
Press the SELECT button 
KeystoneKeystone
Keystion
The top left corner adjustment as an example:
Press the Point ▼ button
Press the Point ► button
Keystone	Correction
Standard
Corner	correction 
						

							
2



Dot
Note:   You	can	choose	the	pattern	of	Pointer	(Arrow/Finger/Dot )	in	the	
Setting	Menu	(p.58)
You can move the Pointer of the projector with the remote control to emph\
asize a part of the projected image.  
Press the POINTER button to activate the Pointer function.1
2

MOUSE	POINTER	button
POINTER	button
To cancel the Pointer function, press the POINTER button 
again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
The remote control can be used as a wireless mouse for your computer. 
Move the pointer on the screen with this button.  MOUSE	POINTER	
button
R-CLICK	button
L-CLICK	button
Acts as right (click) mouse button while the projector and a computer are connected with a USB cable.
Acts as left (click) mouse button while the projector and a computer are connected with a USB cable.
Before operating the wireless mouse, connect your computer 
and the projector with the supplied USB cable (p.19).
When the Pointer function is used, the wireless mouse is not 
available. 
When a USB cable is connected to the computer and the 
projector, turn on the projector first, then the computer. If you 
turn on the computer first, the wireless mouse function may 
not operate properly.
1
2
Basic	Operation
Pointer	Function
Wireless	Mouse	Operation
ArrowFinger 
						

							


The input source changes each time you press the INPUT button on the side control or the remote control as follows:
 Input 1→ Input 2→ Input 3 → ...
Before using the INPUT button on the side control or the remote control, you must select a cor\
rect input source by On-
Screen Menu and the latest input source will be displayed.
Input	Selection
Press the INPUT 1, INPUT 2, or INPUT 3 button on the remote control. The input source appears on the screen as you 
press each button. Select the connected input source.
INPUT	1	buttonInput	1
RGB	(PC	analog)
RGB	(Scart)
RGB	(PC	digital)
RGB	(AV	HDCP)
INPUT	2	buttonInput	2
Video
y,Pb/Cb,Pr/Cr
RGB
INPUT		button
Input	
Video
y,Pb/Cb,Pr/Cr
S-video
Side	Control
Remote	Control
INPUT	button*
* Only the Input button function is set Mode	1	in the Setting menu, the INPUT button is used for switching 
  input source.
INPUT	button*
Direct	Operation
Remote	Control	Operation
Side	Control/Remote	Control	Operation
INPUT	buttons
Remote	Control 
						

							
4

INPUT	MENU
When your computer is connected to INPUT 1 (DIGITAL) 
terminal, select RGB(PC	digital).
When your computer is connected to the INPUT 1 (ANALOG) 
terminal, select RGB	(PC	analog).
RGB(PC	digital)
RGB(PC	analog)
Note:
	 •	 Input	source	changes	if	the	INPUT	1	button	on	the	remote	control	is	pressed.
	 •	 HDCP 	(High-bandwidth	Digital	Content	Protection)	is	a	system	for	
protecting	digital	entertainment	content	which	is	delivered	by	DVI	
(Digital	Visual	Interface)	from	being	copied.	The	specification	of	HDCP 	
is	decided	and	controlled	by	Digital	Content	Protection,	LLC.	Should	
the	specification	be	changed,	this	projector	may	not	display	the	digital	
content	protected	by	HDCP.
When connecting the computer output [5 BNC Type (Green, Blue, 
Red, Horiz. Sync, and Vert. Sync.)] from the computer to G, B, R, 
H/HV, and V jacks:
Input	Selection
When your computer is connected to the INPUT 2 (5 BNC 
INPUT JACKS) terminal, select RGB.
RGB	
1
2

Input 1                                                RGB(PC analog)Input 2                                                RGBInput 3                                                Video
System                                               Auto
Input 1                                                RGB(PC analog)Input 2                                                RGBInput 3                                                Video
System                                               SVGA 1
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the 
Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select the desired input and 
then press the Point ► button to access the submenu items. 
Use the Point ▲▼ buttons to select the desired source	and 
then press the SELECT button.
Input 1RGB(PC analog)RGB(Scart)RGB(PC digital)RGB(AV HDCP)
Y,Pb/Cb,Pr/Cr
INPUT	2	MENU INPUT	1	MENU
Computer	Input	Source	Selection
WHEN	SELECTING	INPUT	1	(COMPUTER	INPUT	
TERMINALS	)
WHEN	SELECTING	INPUT	2	(5	BNC	INPUT	jACKS	)
Menu	Operation 
						

							
5

When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select Video.
When the video input signal is connected to the 
S-VIDEO jack, select S-video.
When connecting to video equipment, select the type of Video 
source in the Source Select Menu. 
When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select 
y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select Video.
When connecting to video equipment, select the type of Video 
source in the Source Select Menu. 
Video
y,Pb/Cb,Pr/Cr
Video
S-video
Input	Selection
When connecting to video equipment, select the type of Video 
source in the Source Select Menu.  INPUT	1	MENU
RGB(AV	HDCP)
RGB(Scart)
When scart video equipment is connected to the INPUT 1 
(ANALOG) terminal, select 
RGB	(Scart).
If the HDCP-compatible signal source is connected to the 
INPUT 1 (DIGITAL) terminal, select  RGB	(AV	HDCP).
Y,Pb/Cb,Pr/Cr
INPUT	2	MENU
Y,Pb/Cb,Pr/Cr
INPUT		MENU
y,Pb/Cb,Pr/Cr
1
2

Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the 
Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select the desired input and 
then press the Point ► button to access the submenu items. 
Use the Point ▲▼ buttons to select the desired source	and 
then press the SELECT button.
Video	Input	Source	Selection
Menu	Operation
Note:
	 •	 When	the	video	input	signal	is	connected	to	the	 Y-Pb/Cb-Pr/Cr	jacks,	Y,Pb/Cb,Pr/Cr takes	precedence	of	RGB.
	 •	 Y,Pb/Cb,Pr/Cr	input	can	accept	the	component	signal	and	the	analog	
RGB	signal.	When	analog	RGB	signal	is	not	recognized	in	 Y,Pb/Cb,Pr/
Cr	input	source,	set	to	
RGB 	input	manually.
WHEN	SELECTING	INPUT	1	(COMPUTER	INPUT	
TERMINALS	)
WHEN	SELECTING	INPUT	2	(5	BNC	INPUT	jACKS	)
WHEN	SELECTING	INPUT		(AV	TERMINALS	) 
						

							
6

Computer	Input
System                                             SVGA 1
Input 1                                               RGB(PC analog)Input 2                                               RGBInput 3                                               Video
PC	System	MenuPC	System	Menu
1
2
PC system can also be selected manually.
The PC System Menu  
Selected system is    
displayed.
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the Point 
► or the SELECT button. 
Use the Point ▲▼ buttons to select Systerm and then press 
the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired system and 
then press the SELECT button.
System        RGB(Input 2)
Systems in this dialog box can be selected.
Customized  Mode	(1-10) set in 
the PC adjust Menu (pp.38-39).
This projector automatically tunes to various types of computers with it\
s Multi-scan system and Auto PC adjustment. If a 
computer is selected as a signal source, this projector automatically de\
tects the signal format and tunes to project a proper 
image without any additional settings. (Signal formats provided in this\
 projector are shown on pages 79-80)
One of the following messages may appear when:
When the projector cannot recognize the connected 
signal conforming to the provided PC Systems, Auto 
is displayed on the System Menu box and the Auto PC 
adjustment function works to display proper images. 
If the image is not projected properly, a manual 
adjustment is required (pp.38-39).
There is no signal input from the computer. Check the 
connection between your computer and the projector. 
(See “Troubleshooting” on pp.70-72.)
Auto
-----
The preset system is manually adjusted in the PC 
adjust Menu. The adjusted data can be stored in 	Mode	
1-10 (pp.38-39).
Mode	1
PC Systems provided in this projector is chosen.  The 
projector chooses a proper system provided in the 
projector and displays it.  
SVGA	1
*Mode	1 and  SVGA 	1 are examples.  
Computer	System	Selection
Automatic	Multi-Scan	System
Selecting	Computer	System	Manually 
						

							
7

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V positions to 
conform to your computer. 
To	store	the	adjusted	parameters .The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.36). See “Manual PC Adjustment” on pages 38-39.
Note:
	 •	 Fine	sync,	Total	dots,	Position	H	and	Position	V	position	of	certain	computers	cannot	be	fully	adjusted	with	the	 Auto	PC	Adjustment	
function.	When	the	image	is	not	provided	properly	with	this	operation,	
manual	adjustments	are	required.	(pp.38-39)
	 •	 Auto	PC	 Adjustment	cannot	be	operated	in	Digital	Signal	Input	on	the 	
DVI	terminal	and	480p,	575p,	480i,	575i,	720p,	1035i,	1080i	or	1080p	is	
selected	on	the	PC	SYSTEM	Menu.
	 •	 Depending	on	the	condition	of	signals	and	the	type	and	length	of	 cables,	the	signals	may	not	be	properly	viewed.
The Auto PC adjustment function can be operated directly by 
pressing the AUTO PC button on the remote control.
AUTO PC button
Remote	Control
Computer	Input
PC	adjust	MenuPress the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select  PC	adjust and then press 
the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons to select  Auto	PC	adj . and then 
press the SELECT button.
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \
0Current modeClamp                                                                   \
 0Display area H                                                       102\
4Display area V                                                        76\
8ResetMode freeStore
                                                             0
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \
0Current modeClamp                                                                   \
 0Display area H                                                       102\
4Display area V                                                        76\
8ResetMode freeStore
                                                             0
Use the Point ▲▼ buttons to select Auto	PC	
adj . and press the SELECT button.
Please	wait . . . appears while the Auto PC adjustment is in process.
Auto	PC	 Adjustment
Direct	Operation
Menu	Operation
Auto	PC	adj . 
						

							


Some computers employ special signal formats which may not be tuned by M\
ulti-Scan system of this projector. Manual PC 
Adjustment enables you to precisely adjust several parameters to match t\
hose special signal formats. The projector has 
10 independent memory areas to store those parameters manually adjusted.\
 It allows you to recall the setting for a specific 
computer. 
Note:  The	PC	Adjust	Menu	cannot	be	operated	when	the	digital	signal	input	on	the	DVI	terminal	is	selected	on	PC	System	
Menu. 
Use  the  Point ◄► buttons  to  adjust  the  value,  eliminating  a  flicker 
from the image displayed (from 0 to 31).
Use the Point ◄► buttons to adjust the number of total dots in one 
horizontal period to match your PC image.
Use the Point ◄► buttons to adjust the horizontal picture position.
Use the Point ◄► buttons to adjust the vertical picture position.
Press  the  SELECT  button  to  show  H-sync  freq.  and  V-sync  freq.  of  
the connected computer.
Use  the  Point ◄►  buttons  to  adjust  the  clamp  level.  When  the 
image has dark bars, try this adjustment.
Use  the  Point ◄►  buttons  to  adjust  the  horizontal  area  displayed 
by this projector.
Use the Point ◄► buttons to adjusts the vertical area displayed by 
this projector.
Computer	Input
PC	adjust	Menu1
2
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select  PC	adjust and then press the 
Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and then 
press the SELECT button to display the
adjustment dialog box. Use the Point ◄► buttons to adjust the 
setting value.
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \
0Current modeClamp                                                                   \
 0Display area H                                                       102\
4Display area V                                                        76\
8ResetMode freeStore
                                                             0
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \
0Current modeClamp                                                                   \
 0Display area H                                                       102\
4Display area V                                                        76\
8ResetMode freeStore
                                                             0
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \
0Current modeClamp                                                                   \
 0Display area H                                                       102\
4Display area V                                                        76\
8ResetMode freeStore
                                                             0
Fine	sync
Total	dots
Position	H
Position	V
Current	mode
Clamp
Display	area	H
Display	area	V
Manual	PC	Adjustment 
						

							
9

Computer	Input
Note:
•	Display area (H/V)	cannot	be	selected	when	480i,	575i,	
480p ,	575p,	720p,	1035i 	or	1080i	is	selected	in	the	PC	
System	Menu	(p.36).
•	When	input	computer	signal	to	the	projector,	PC	adjust	function will	become	available.
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \
0Current modeClamp                                                                   \
 0Display area H                                                       102\
4Display area V                                                        76\
8ResetMode freeStore
                                                             0
Mode 1Mode 2Mode 3Mode 4Mode 5Mode 6Mode 7Mode 8Mode 9Mode 10
00
Total dots                                 1344Position H                                  255Position V                                    34Display area H                         1024 Display area V                           768
Where to free?
store?Store
Total dotsPosition HPosition VDisplay area HDisplay area V
00
Mode 1Mode 2Mode 3Mode 4Mode 5Mode 6Mode 7 Mode 8Mode 9Mode 10
Free
00
Total dots                                 1344Position H                                  255Position V                                    34Display area H                         1024 Display area V                           768
Where to store?
Vacant
This mode has stored parameters.
Values of  Total	dots, Position	H, 
Position	V,  Display	area	H and 
Display	area	V.
Press the SELECT button to store the data.
Press the MENU button to close this dialog box.
Mode	free
Store
To  store  the  adjusted  data,  select Store  and  then  press  the  Point ►  or the  SELECT  button.  Move  the  highlight  to  one  of  the  Modes 1  to  10  in  which  you  want  to  store,  and  then  press  the  SELECT button.
To clear the stored data, select  Mode	free and then press the Point ► or the SELECT button. Move the highlight  to the Mode that you want to clear and then press the SELECT button.
To  reset  the  adjusted  data,  select Reset  and  press  the  SELECT button.  A  confirmation  box  appears  and  then  select  yes.  All adjustments will return to their previous figures.  
Reset
Mode	free
Store
Press the SELECT button to clear the stored data. 
						

							
40

1
2
Normal picture level preset on the projector.
Picture level with improved halftone for graphics.
User preset picture adjustment in the Image adjust Menu. (p.42)
Computer	Input
Image	select	Menu
Press the MENU button to display the On-Screen Menu. 
Use the Point ▲▼ buttons to select Image	select and 
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
StandardRealImage 1Image 2Image 3Image 4Image 5Image 6Image 7Image 8Image 9Image10
StandardRealImage 1Image 2Image 3Image 4Image 5Image 6Image 7Image 8Image 9Image 10
Image	Level	Selection
Menu	Operation
Standard
Real
Image	1–10