Eiki Lc-Xb43n Multimedia Projector Owners Manual

							
41

Choose Video or S-video by pressing the INPUT button on 
the top control or the VIDEO button on the remote control.
1

Video
Input	Menu
Input	Source	Selection	(Video,	S-video)
Video	Input
Direct	Operation
Menu	Operation
When video input signal is connected to the 
VIDEO jack, select Video.Video
When video input signal is connected to the S-
VIDEO jack, select S-video.S-video
Note:
 • Network  is  for  the  Network  function.  See  the  owner’s 
manual of “Network Set-up and Operation” .
 • When  the  Input  Search  function  is  set  to On1  or On  in 
the Auto setup function, the input signal will be searched 
automatically (p.49).
Top	ControlINPUT	button
Remote	Control
VIDEO	button
    Wired 1
RGBRGB(PC digital)
    Wired 1
RGBRGB(PC digital)
Press the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select Input and 
then press the Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select either Video or 
S-video and then press the SELECT button.
Video
S-videoVideo
S-video
Computer	(RGB(PC	digital)	/	RGB(AV	HDCP)	/	RGB(Analog))
Network
Computer1	((RGB)	/	
(Component)	/	(Scart)) 
						

							
4

Video	Input
Choose Computer	1(Component)  or Computer	1(Scart)  by  pressing  the  INPUT  button  on  the  top  control  or 
press the COMPUTER button on the remote control.
Before  using  these  buttons,  correct  input  source  should  be  selected  through  Menu  operation  as  described 
below.
Input	Menu
Input	Source	Selection	(Component,	RGB	Scart	1-pin)
Direct	Operation
Menu	Operation
Note: 
 • Network is for the Network function. See the owner’s manual of “Network Set-up and Operation” .
 • When the Input Search function is set to On1 or On, 
the input signal will be searched automatically (p.49).
COMPUTER	button
Top	Control
INPUT	button
Remote	Control
VGA
Computer1	((RGB)	/	
(Component)	/	(Scart))
Computer	(RGB(PC	digital)	/	
RGB(AV	 HDCP)	/	RGB(Analog))
1
Use the Point ▲▼ buttons to select Computer	1 and 
then press the Point ► button.
When the input source is coming from video 
equipment connected to the COMPUTER 
IN 1/COMPONENT IN terminal with a 
Component-VGA Cable, select Component. 
Component
When the input source is coming from video 
equipment connected to the COMPUTER 
IN 1/COMPONENT IN terminal with a Scart-
VGA Cable, select RGB	(Scart). 
RGB	(Scart)
Press the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select Input and 
then press the Point ► or the SELECT button. 
3Use the Point ▲▼ buttons to select Component or 
RGB(Scart)	and then press the SELECT button.
Video
S-video
Computer	(RGB(PC	digital)	/	RGB(AV	HDCP)	/	RGB(Analog))
Network
Computer1	((RGB)	/	
(Component)	/	(Scart)) 
						

							
43

Video	Input
Video	System	Selection
1AV	System	Menu	(Video	or	S-video)
AV	System	Menu	(Component)

If the projector can not reproduce proper video image, 
select a specific broadcast signal format from among PAL, 
SECAM,	NTSC, NTSC	4 .43, PAL-M and	PAL-N.
PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
The projector automatically detects an incoming video 
signal, and adjusts itself to optimize its performance.
If the projector can not reproduce proper video image, select 
a specific component video signal format among 480i,	55i, 
480p, 55p,	0p,	1035i and 1080i.
Auto
COMPONENT	VIDEO	SIGNAL	FORMAT
The projector automatically detects an incoming video 
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system 
manually.
Auto
Note:
The AV System Menu can not be selected when selecting 
RGB	(Scart).
Video
Component
Press the MENU button to display the On-Screen 
Menu.  Use the Point ▲▼ buttons to select Input and 
then press the Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select Video, S-video 
or Computer	1(Component) and then press the 
SELECT button.
3Use the Point ▲▼ buttons to select System and then 
press the Point ► or the SELECT button. Use the Point 
▲▼ buttons to select the desired system and then 
press the SELECT button.
Video	or	S-video
Component 
						

							
44

Image	Select	Menu
Select the desired image mode among Dynamic, Standard, 
Cinema, Blackboard	(Green), Colorboard, Image	1, 
Image	, Image	3 and Image	4 by pressing the IMAGE 
button on the remote control.
Standard
Picture mode adjusted with fine tone.
Cinema
Image	1–4
IMAGE	button
Dynamic
Cinema
Blackboard	(Green)
Dynamic
Standard
Remote	Control
IMAGE	button
Direct	Operation
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
For viewing with the user preset image mode in the Image 
adjust Menu (see pages 45-46). This Image memory is 
provided in each computer, component and video input 
source.
1

Image	1
Image	
Image	3
Image	4
Colorboard
Colorboard
Use the Point ▲▼ buttons to select Colorboard and then 
press the Point ► or the SELECT button. Use the Point 
▲▼ buttons to select the desired item and then press the 
SELECT button.
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Press the MENU button to display the On-Screen Menu. 
Use the Point ▲▼ buttons to select Image	select and 
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
Video	Input
For the image projected on a blackboard.
This mode helps enhance the image projected on a 
blackboard. This is mainly effective on a green colored 
board, not truly effective on a black colored board.
Image	Mode	Selection	
Menu	Operation
Blackboard	(Green) 
						

							
45

Video	Input
Image	Adjustment
1

Press the Point ◄ button to decrease the contrast; press the 
Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press  
the Point ► button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point ◄ button to lighten red tone; press the Point 
► button to deepen red tone (from 0 to 63).
white	balance	(Red)
Press the Point ◄ button to lighten green tone; press the 
Point ► button to deepen green tone (from 0 to 63).
white	balance	(Green)
Press  the  Point ◄  button  to  lighten  blue  tone;  press  the 
Point ► button to deepen blue tone (from 0 to 63).
white	balance	(Blue)
Use the Point ◄► buttons to select the desired Color temp. 
level (XLow, Low, Mid or High ). 
Color	temp .
Press the Point ◄ button decrease the intensity of the color; 
press the Point ►button increase the intensity of the color 
(from 0 to 63).
Press the Point ◄► buttons to adjust the tint value to get a 
proper color balance (from 0 to 63).
Color
Tint
Note:
 •  When	white	balance	Red, Green or Blue is adjusted, the Color temp. level will change to User.
 • Tint can not be selected when the video system is PAL, SECAM, PAL-M or PAL-N	(p.43).
 •  When Blackboard(Green)	or Colorboard is selected in Image select, Color	temp . will change to   
   Blackboard or Colorboard.
Image	adjust	Menu
ResetStore
Selected Image mode
Press the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select Image	
adjust and then press the Point ► or the SELECT 
button.
Use the Point ▲▼ buttons select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point ◄► buttons to 
adjust the setting value.
ResetStore
Use the Point ◄► 
buttons to adjust the 
setting value. 
						

							
46

Video	Input
Use  the  Point ◄►  buttons  to  adjust  the  gamma  value  to 
obtain a better balance of contrast (from 0 to 15).
Gamma
Press the Point ◄ button to decrease the sharpness of the 
image; Press the Point ► button to increase the sharpness 
of the image (from 0 to 15).
Sharpness
An interlaced video signal can be displayed in progressive 
mode. Select one of the following options.
 Off .........  Disabled.
 L1 ..........  For an active picture.
 L ..........  For a still picture.
 Film .......  For watching a film. With this function, the 
projector reproduces pictures faithful to the 
original film quality.
Progressive
Noise	reduction
Noise interference on the screen can be reduced. Select 
one of the following options to get smoother images.
 Off .........  Disabled.
 L1 ..........  Lower reduction.
 L ..........  Higher reduction.
Note: 
    Noise	reduction and Progressive can not be selected 
when 480p, 55p, 0p, 1035i or 1080i	is selected 
(p.43).
To reset the adjusted data, select Reset	and press the the 
SELECT button. A confirmation box appears and then select 
y es. All adjustments will return to their previous figures. 
Reset
Store
To store the adjusted data, select Store and press the 
Point ► or the SELECT button. Use the Point ▲▼ buttons 
to select one from Images 1 to 4 and press the SELECT 
button. 
A confirmation box appears and then select yes. Stored 
data can be called up by selecting an Image	(1-4) in the 
Image Mode Selection on page 44.
A confirmation box 
appears and then 
select yes.
Store	Menu 
						

							
4

Video	Input
This projector has the picture screen resize function, which enables you to customize the image size.
Screen	Menu1

Provide the image to fit the screen size while maintaining
the aspect ratio of input signal.
Adjust the screen scale and position manually with this 
function.
Press the Point ► button at Custom and the Custom is
displayed on the screen, you can use the Point ▲▼ buttons
to choose the item you want to adjust.
 Scale	H/V ..........  Adjust the Horizontal/Vertical screen 
scale.
 H&V ...................  When set to On, the aspect ratio is fixed. 
Scale	V appears dimmed and becomes 
unavailable. Adjust the Scale	H, then the 
screen scale is automatically modified 
based on the aspect ratio. 
 Position 	H/V.....Adjust  the  Horizontal/Vertical  screen 
position.
 Common ...........  Save the adjusted scale to all the inputs. 
Press the SELECT button at Common 
to display a confirmation box. To save 
the scale, press the SELECT button 
at y es, When Custom is selected, the 
saved scale is used.
 Reset .................  Reset the all adjusted values. Press 
the SELECT button at Reset to display 
a confirmation box. To reset, press the 
SELECT button at y es.
Note:
 • When no signal is detected, Normal is set 
automatically and the Aspect dialog box 
disappears.
 • The adjustable range for Scale	H/V and 
Position	H/V is limited depending on the 
input signal.
 • w ide, Zoom	and Natural	wide	can not 
be operated when 0p, 1035i or 1080i is 
selected in the AV System Menu (p.43).
 • The corner pattern mode is disable when 
in Custom mode.
Provide the image at the 16:9 wide screen ratio.
Press the MENU button to display the On-Screen 
Menu. Use the Point ▲▼ buttons to select Screen and 
then press the Point ► or the SELECT button
Use the Point ▲▼ buttons select the desired item and 
then press the SELECT button.
Normal
wide
Custom
Screen	Size	 Adjustment 
						

							
48

Language
The language used in the On-Screen Menu is available in 
English,	German,	French,	Italian,	Spanish,	Portuguese, 
Dutch,	Swedish,	Finnish,	Polish, Hungarian,	Romanian, 
Russian,	Chinese,	Korean, japanese	and Thai.
Setting	Menu
Setting
Press the MENU button to display the On-Screen 
Menu.  Press the Point ▲▼ buttons to select Setting 
and press the Point ► or the SELECT button to access 
the submenu items.
1
Use the Point ▲▼ buttons to select the desired item 
and then press the Point ► or the SELECT button to 
access the selected item.
This projector has a Setting menu that allows you to set up 
the other various functions described below.
Language
Menu	position
This function is used to change the position of the 
On-Screen Menu. Select Menu	position and press the 
Point ► or the SELECT button.  
The Menu position changes each time you press SELECT 
button as follows.
the top left   the top right   the center  the bottom left 
 the bottom right  the top left  .....
3Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
Setting 
						

							
49

Setting
Note:
 • Auto	Keystone corrects vertical distortion only, not 
correct horizontal distortion.
 • The Auto Keystone function can not work when the 
Ceiling	is set On in the Setting menu (p.54).
 • Perfect correction of the image distortion can not 
be ensured with the Auto setup function. If the 
distortion is not corrected properly by pressing the 
AUTO SETUP/CANCEL button, adjust manually 
by pressing the KEYSTONE button on the remote 
control or selecting Keystone in the Setting menu 
(pp.27,50).
 • Fine	sync, Total	dots, Horizontal and Vertical of 
some computers can not be fully adjusted with the 
Auto PC adjustment function. When the image is 
not provided properly with this operation, manual 
adjustments are required (pp.35-36).
Auto	setup
Input	search
This function detects the input signal automatically. When 
a signal is found, the search will stop. Use the Point ▲▼ 
buttons to select one of the following options.
Off ......Input search will not work.
On	1  ...Input search works under the following situation.
  – When pressing the AUTO SETUP/CANCEL 
button on the top control.
  – When pressing the AUTO SET/CANCEL button 
on the remote control.
On	 ...Input search works under the following situation.
  – When turning on the projector by pressing the 
ON/STAND-BY button on the top control or the 
remote control.
  – When pressing the AUTO SET/CANCEL button 
on the remote control.
  – When pressing the AUTO SETUP/CANCEL 
button on the top control.
  –  When the current input signal is cut off.*
* If the No show or Freeze function is active, cancel it to 
activate the Input search. It is also unavailable when On-
Screen menu is displayed.Auto	PC	adj .
On. . . . . .  Enables Auto PC adjustment when pressing       
                   the AUTO SET/CANCEL button on the remote 
                   control or the AUTO SETUP/CANCEL button 
                   on the top control.
Off. . . . . .  Disables Auto PC adjustment.
	Auto	Keystone	
Auto . . . .   Always works and corrects keystone 
distortion according to the projector's tilt.
Manual  . .  Works only when pressing the AUTO SETUP/
CANCEL button on the top control or the 
AUTO SET/CANCEL button on the remote 
control.
Off. . . . . .  Disables Auto Keystone.
Auto	setup	Menu
Note:
  •While Input	search is set to On	1 or On	, the status of Input 
and Lamp are displayed every time the signal is switched.
 •Only the last selected input source can be detected.
 •If the INPUT button on the top control or the COMPUTER, 
VIDEO or NETWORK buttons on the remote control is pressed 
during Input search is in progress, Input search will stop and go 
back to the previous input signal.
  • Input	 search,	 Auto	PC	adj .	and	Auto	 Keystone  can  not  be 
set Off at the same time. 
This function enables Input search, Auto Keystone correction 
and Auto PC adjustment by pressing the AUTO SETUP/
CANCEL button on the top control or the AUTO SET/CANCEL 
button on the remote control. Settings for those functions can 
be altered as follows: 
						

							
50

Keystone
Select the background screen for when no input signal is 
detected. Press the Point ▲▼ buttons to switch between 
each option.
 Blue . . . Blue colored background.
 User. . . The image you captured.
 Black  . . Black colored background.
Setting
KeystoneThis function is used to adjust keystone distortion of the  
projected image. Use the Point ▲▼ buttons to choose the 
item you want to adjust.
Adjust the Horizontal/Vertical keystone distortion of the  
projected image.
Standard 
 Corner	correction
Adjust the corner distortion of the projected image.
Corner	pattern
Choose a Corner pattern mode among Red, white, 
Blue, and Off.  
	Store
				Store .....Keep the keystone correction even when the            
                    AC power cord is unplugged.
    Reset .....Release  the  keystone  correction  when  the 
AC power cord is unplugged.
Press the KEYSTONE button on the remote control to 
switch the Standard (for Vertical/Horizontal) /Corner 
correction adjustment. The Standard or Corner 
correction adjustment dialog box appears. Use the Point 
▲▼◄► buttons to correct the Standard or Corner 
distortion (p.27). 
Background