Eiki Lc-Xb41 Multimedia Projector Owners Manual

							31
Computer Input
Move the red frame pointer to
the mode and press the
SELECT button.
The level being selected.
Image Select Menu
Image Select Menu icon
IMAGE button
Dynamic
Real
Image 1
Image 2
Image 3
Image Mode Selection 
Image 4
Blackboard (Green)
Standard
Remote Control
IMAGE
button
Normal picture mode preset on the projector.Standard
Picture mode with improved halftone for graphics.Real
For the image projected on a blackboard. See above for
further description.Blackboard(Green)
For viewing with the user preset image mode in the Image
Adjust Menu (see page 33).Image 1~4
For viewing pictures in a bright room.
Dynamic
Select the desired image mode from among Dynamic,
Standard, Real, Blackboard (Green), Image 1, Image 2,
Image 3, and Image 4 by pressing the IMAGE button on the
remote control.
Standard
Picture mode with improved halftone for graphics. Real
Blackboard (Green)
Image 1–4
For the image projected on a blackboard.
This mode help enhance the image projected on a blackboard.
This is mainly effective on a green colored board, not truly
effective on a black colored board. Dynamic
Direct Operation
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
For viewing with the user preset image mode in the Image
Adjust Menu (see page 33). This Image memory is provided
in each computer, component, and video input source.
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Image Select Menu icon.1
2Use the Point edbuttons to move the red frame
pointer to the desired image mode and then press the
SELECT button.
Menu Operation 
						

							32
Press the Point7 8 buttons 
to adjust the value.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
frame pointer to the Image Adjust Menu icon.1
2Use the Point edbuttons to move the red frame
pointer to the desired item and then press the SELECT
button to display the adjustment dialog box. Use the
Point 
7 8buttons to adjust the setting value.
Move the red frame
pointer to the item to be
selected and then press
the SELECT button.
Image Adjust Menu
Image Adjust Menu icon
Selected Image level
Image Adjustment
Computer Input
✔Note: After adjusting any of the White balance Red,
Green or Blue, the Color temp will change to
Adj..
Reset
Press the Point 7button to decrease the contrast; press
the Point 
8button to increase the contrast (from 0 to 63).
Press the Point 7button to decrease the brightness; press
the Point 
8button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point 7button to lighten red tone; press the
Point 
8button to deepen red tone (from 0 to 63).
White balance (Red)
Press the Point 7button to lighten green tone; press the
Point 
8button to deepen green tone (from 0 to 63).
White balance (Green)
Press the Point 7button to lighten blue tone; press the
Point 
8button to deepen blue tone (from 0 to 63).
White balance (Blue)
Use the Point 7 8buttons to select the desired Color temp.
level (High, Mid, Low, or XLow).  Color temp.
Use the Point 7 8buttons to adjust the gamma value to
obtain a better balance of contrast (from 0 to 15). Gamma
Press the Point 7button to decrease the sharpness of the
image; press the Point 
8button to increase the sharpness
of the image (from 0 to 15). Sharpness
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
[Yes]. All adjustments will return to their previous figures.  
						

							33
Computer Input
Store
Exit the Image Adjust Menu.
Quit
To store the adjusted data, select Store and press the
SELECT button.  Use the Point ed buttons to select one
from Image 1 to 4 and press the SELECT button. 
A confirmation box appears and then select [Yes]. Stored
data can be called up by selecting Image (1-4) in the Image
Select Menu on page 31.
This projector has the picture screen resize function, which enables you\
 to customize the image size.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
frame pointer to the Screen Menu icon.1
Move the red frame pointer
to the function and press
the SELECT button.
Use the Point edbuttons to move the red frame
pointer to the desired function and then press the
SELECT button.2
Screen Menu
Screen Menu icon
Screen Size Adjustment
Wide
Provide the image to fit the screen size. Normal
True
Provide the image in its original size.  When the original
image size is larger than the screen size (1024 x 768), the
projector enters panning mode automatically.  Pan the
image with Point 
ed7 8
buttons.  When adjusted, the
arrows will turn red.  When reached to the correction limit,
the arrows will disappear.
Provide the image to fit wide video aspect ratio (16 : 9) by
expanding the image width uniformly.  This function can be
used for providing a squeezed video signal at 16 : 9.
Full screen
Provide the full screen image. 
✔Notes:
• The Screen Menu, except for Normal and Custom, cannot be operated when 720p,
1035i, or 1080i is selected in the PC System
Menu  (p.27).
• The projector cannot display any resolution higher than 1600 X 1200.  If your computer’s
screen resolution is higher than it, reset the
resolution to the lower before connecting to the
projector.
• The image data other than 1024 x 768  is
modified to fit the screen size in initial mode.
• True, Full screen, and Digital zoom +/– cannot be selected when 480i, 575i, 480p, or 575p is
selected in the PC System Menu  (p.27).
Store icon
Image Mode Menu
Move the red frame
pointer to an image
item to be set and
then press the
SELECT button.
A confirmation
box appears
and then select
[Yes] 
						

							Remote Control 
D.ZOOM + button
POINT buttons
SELECT button
D.ZOOM - button
34
Computer Input
✔Notes:
• The panning function may not operate properly if
the stored Mode in the PC Adjust Menu is used.
(p.30)
• The minimum compression ratio can be limited
depending on the input signal or when the
Keystone function is working.
• True, Full screen, and Digital zoom +/– cannot be selected when 480i, 575i, 480p, or 575p is
selected in the PC System Menu  (p.27).
• Digital zoom +/- cannot be selected when Full
screen or True is selected.
Select Digital zoom +. The On-Screen Menu disappears and
“D. zoom +” appears. Press the SELECT button to expand
the image size. Use the Point 
ed7 8buttons to pan the
image. The Panning function can work only when the image
is larger than the screen size.
A projected image can be also expanded by pressing the
D.ZOOM 
ebutton on the remote control. 
To exit the Digital zoom +/– mode, press any button except
the D.ZOOM 
edbuttons, SELECT, and Point buttons.
Digital zoom +
Select Digital zoom –. The On-Screen Menu disappears and
“D. zoom –” appears. Press the SELECT button to compress
image size. 
The projected image can be also compressed by pressing the
D.ZOOM 
d button on the remote control.  
Digital zoom –
To return to the previous screen size, select a screen size
from the Screen Size Adjustment Menu or select an input
source from the Input Source Selection Menu (see page 26)
again, or adjust the screen size with the D.ZOOM 
ed
buttons.
F or zooming in and out the images
Adjust the screen scale and position manually with this
function.
Press the SELECT button at Custom and the “Custom” is
displayed on the screen for a few seconds and then the
Aspect dialog box appears.
Scale H/V............ Adjust the Horizontal/Vertical screen scale.
H&V.................... When set to “On,” the aspect ratio is fixed. The “Scale V” appears dimmed and
becomes unavailable. Adjust “Scale H,”
then the screen scale is automatically
modified based on the aspect ratio. 
Position H/V ....... Adjust the Horizontal/Vertical screen position.
Common ............ Save the adjusted scale to all the inputs. Press the SELECT button at Common to
display a confirmation box. To save the
scale, press the SELECT button at “Yes.”
When Custom is selected, the saved scale
is used.
Reset.................. Reset the all adjusted values. Press the SELECT button at Reset to display a
confirmation box. To reset, press the
SELECT button at “Yes.”
Custom
✔Notes:
•W hen no signal is detected, “Normal” is set
automatically and the Aspect dialog box disappears.
• The adjustable range for Scale H/V and Position H/V
is limited depending on the input signal.
Press the SELECT button at
Common or Reset, to display a
confirmation box. 
						

							35
Choose Video by pressing the VIDEO button on the top
control or the remote control.
Before using these buttons, correct input source should be
selected through menu operation as described below.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
frame pointer to the Input Menu icon.
Press the Point edbuttons to move the red arrow
pointer to Video and then press the SELECT button to
display the Source Select Menu . 
1
2
Move the pointer to
Video and press the
SELECT button.
VIDEO
Move the pointer to the
source that you want to
select and press the
SELECT button.
Source Select Menu (VIDEO)
Input Menu
Move the pointer to the desired source and then press
the SELECT button.3
When selecting Auto, the projector automatically
detects incoming video signal, and adjusts itself
to optimize its performance.  The projector
selects connection in the following order:
1. S-Video
2. Video Auto
When video input signal is connected to the
VIDEO jack, select Video.Video
When video input signal is connected to the S-
VIDEO jack, select S-Video.S-Video
Input Source Selection (Video, S-Video)
Direct Operation
Menu Operation
Input Menu icon
Video Input
REMOTE CONTROL
VIDEO button
T op Control
VIDEO button
✔Note:
•W hen the Input Search function is set to “On1” or “On2”, the
input signal will be searched automatically (p.45). 
						

							36
Choose Computer 2 by pressing the COMPUTER 2 button
on the top control or press the COMPUTER button on the
remote control.
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
frame pointer to the Input Menu icon.1
Computer 2
Input Menu
Press the Point edbuttons to move the red arrow
pointer to Computer 2 and then press the SELECT
button.  2
After the Source Select Menu appeared for Computer
2, move the pointer to Component or RGB(Scart) and
then press the SELECT button.3
Computer 1
Computer 2
Input Source Selection (Component, RGB Scart 21-pin)
Direct Operation
Menu Operation
Move the pointer (red
arrow) to Computer 2
and press the SELECT
button.
Input Menu icon
Move the pointer to
Component or RGB(Scart) 
and press the SELECT
button.
Source Select Menu
REMOTE CONTROL
COMPUTER button
When the input source is coming from video
equipment connected to the COMPUTER IN
2 / COMPONENT IN terminal with a
Component-VGA Cable, select Component. Component
When the input source is coming from video
equipment connected to the COMPUTER IN
2 / COMPONENT IN terminal with a Scart-
VGA Cable, select RGB (Scart). RGB (Scart)
T op ControlCOMPUTER 2 button
Video Input
✔Note:
•W hen the Input Search function is set to “On1” or “On2”, the
input signal will be searched automatically (p.45). 
						

							37
Video Input
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
frame pointer to the AV System Menu icon.1
Vi deo System Selection
AV System Menu (Video or S-Video)
AV System Menu (Component)
Use the Point edbuttons to move the red arrow
pointer to the desired system and then press the
SELECT button.2
If the projector cannot reproduce proper video image, select
a specific broadcast signal format from among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Move the pointer to a
system and press the
SELECT button.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
The projector automatically detects an incoming video
signal, and adjusts itself to optimize its performance.
If the projector cannot reproduce proper video image, select
a specific component video signal format from among 480i,
575i, 480p, 575p, 720p, 1035i, and 1080i. Auto
COMPONENT VIDEO SIGNAL FORMAT
Vi deo or S-Video
Component
The projector automatically detects an incoming video
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system
manually. AutoAV System Menu icon 
Selected system is 
displayed.
Move the pointer to a
system and press the
SELECT button. AV System Menu icon  Selected system is 
displayed.
✔Note:
The AV System Menu cannot be selected when selecting RGB(Scart). 
						

							38
Move the red frame pointer to a
mode and press the SELECT
button.
The selected image mode is check marked.
Image Select Menu
Image Select 
Menu icon
IMAGE button
Dynamic
Cinema
Image 1
Image 2
Image 3
Image 4
Image Mode Selection 
Blackboard (Green)
Standard
Remote Control
IMAGE
button
Video Input
Standard
Cinema
Blackboard(Green)
For viewing with the user preset image mode in the Image
Adjust Menu (see page 39–40).Image1–4
Select the desired image mode from among Dynamic,
Standard, Cinema, Blackboard (Green), Image 1, Image 2,
Image 3, and Image 4 by pressing the IMAGE button on the
remote control.
Standard
Picture mode adjusted with fine tone. Cinema
Blackboard (Green)
Image 1–4
For the image projected on a blackboard.
This mode help enhance the image projected on a blackboard.
This is mainly effective on a green colored board, not truly
effective on a black colored board.
For the image projected on a blackboard. See above for
further description.Dynamic
Dynamic
Direct Operation
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
For viewing with the user preset image mode in the Image
Adjust Menu (see page 39–40). This Image memory is
provided in each computer, component, and video input
source.
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Image Select Menu icon.1
2Use the Point edbuttons to move the red frame
pointer to the desired image mode and then press the
SELECT button.
Menu Operation
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
Picture mode adjusted with fine tone. 
						

							39
Video Input
Press the Point7 8buttons
to adjust the value.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
frame pointer to the Image Adjust Menu icon.1
2Use the Point edbuttons to move the red frame
pointer to the desired item and then press the SELECT
button to display the adjustment dialog box. Use the
Point 
7 8buttons to adjust the setting value.
Move the red frame
pointer to the item you
want to adjust and then
press the SELECT button.
Image Adjust Menu
Press the SELECT button
at this item to display other 
items. Image Adjust Menu icon
Press the SELECT
button at this item to
display previous items.
✔Notes:
•The Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N.
• When the White balance Red, Green, or Blue is adjusted, the Color
temp. level will change to “Adj.”.
Image Adjustment
Press the Point 7button to decrease the contrast; press
the Point 
8button to increase the contrast (from 0 to 63).
Press the Point 7button to decrease the brightness; press
the Point 
8button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point 7button to lighten red tone; press the
Point 
8button to deepen red tone (from 0 to 63).
White balance (Red)
Press the Point 7button to lighten green tone; press the
Point 
8button to deepen green tone (from 0 to 63).
White balance (Green)
Press the Point 7button to lighten blue tone; press the
Point 
8button to deepen blue tone (from 0 to 63).
White balance (Blue)
Use the Point 7 8buttons to select the desired Color temp.
level (High, Mid, Low, or XLow).  Color temp.
Press the Point 7button decrease the intensity of the
color; press the Point 
8 button increase the intensity of the
color (from 0 to 63).
Press the Point 7 8buttons to adjust the tint value to get a
proper color balance (from 0 to 63). Color
Tint 
						

							40
To store the adjusted data, select Store and press the
SELECT button.  Use the point ed buttons to select one
from Image 1 to 4 and press the SELECT button.
A confirmation box appears and then select [Yes]. Stored
data can be called up by selecting Image (1-4) in the Image
Select Menu on page 38.
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
[Yes]. All adjustments will return to their previous figures. 
Reset
Store
Exit the Image Adjust Menu.
Quit
✔Notes:
• Noise reduction and Progressive cannot be selected when 480p,
575p, 720p, 1035i, or 1080i is selected.  (p.37)
•R eset and Store icons will be displayed when any adjustment is
made.
Video Input
Use the Point 7 8buttons to adjust the gamma value to
obtain a better balance of contrast (from 0 to 15). Gamma
Press the Point 7button to decrease the sharpness of the
image; press the Point 
8button to increase the sharpness
of the image (from 0 to 15). Sharpness
An interlaced video signal can be displayed in progressive
mode. Select one of the following options.
Off.......... Disabled.
L1 ........... For an active picture.
L2 ........... For a still picture.
Film ........ For watching a film. With this function, the projector reproduces pictures faithful to the
original film quality.
Progressive
Noise reduction
Noise interference on the screen can be reduced. Select
one of the following options to get smoother images.
Off.......... Disabled.
L1 ........... Lower reduction 
L2 ........... Higher reduction
Image Mode Menu
Move the red frame
pointer to an image
item to be set and
then press the
SELECT button.
Store icon
A confirmation box
appears and then
select [Yes].