Eiki Eip-4500 Dlp Projector Setup Guide

							21
Setting up the Projector Network Environment
3. Setting up a Network
Connection for the
Projector
Settings for such items as the projector’s IP
address and subnet mask are compatible with
the existing network.
1Start Internet Explorer (version
5.0 or later) on the computer, and
enter “http://192.168.150.2/”  in
“Address”, and then press the
“Enter” key.
2If a user name and a password
have not yet been set, just click
the “OK” button.
•If a user name and a password have
been set, input the user name and the
password, and click the “OK” button.
•If the user name or password is entered
incorrectly three times, an error mes-
sage will be displayed.
3When the screen as shown on
the right appears, click “TCP/IP”. 
						

							22
4The TCP/IP setting screen ap-
pears, ready for network settings
for the projector.
Note
•Confirm the existing network’s segment (IP
address group) to avoid setting an IP ad-
dress that duplicates the IP addresses of
other network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”,
you don’t have to change the projector IP
address.
•For details about each setting, consult your
network administrator.
5Click the “Apply” button.
6The set values appear. Confirm
that the values are set properly,
and then click the “Confirm” but-
ton.
•After setting items, wait for 10 seconds
and then re-access.
Setting up the Projector Network Environment
This completes the network settings.
Change the IP address of the setting computer back to its original address, and then con-
nect the computer and the projector to the network.
Setting example / Remarks
Factory default setting: 192.168.150.2
Enter an IP address appropriate
for the network.
Factory default setting: 255.255.255.0
Set the subnet mask to the same
as that of the computer and
equipment on the network.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Items
IP Address
Subnet
Mask
Default
Gateway
DNS
Server 
						

							23
Controlling the Projector via LAN
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external equipment
before starting the operation. (See pages 24-
36 on the owner’s manual of the projector.)
Complete the AC cord connection. (See page
37 on the owner’s manual of the projector)
Note
•When connecting the projector to the LAN, use a
commercially available LAN cable (UTP cable,
Category 5, 
cross-over type). When connecting
the projector to a hub, use a straight-through cable.
1Start Internet Explorer (version 5.0
or later) on the computer.
2Enter “http://” followed by the
projector IP address set by the
procedure on page 22 followed
by “/” in “Address”, and then
press the “Enter” key.
•The factory default setting for the projector
IP address is 192.168.150.2. If you did not
change the IP address in “3. Setting up a
Network Connection for the Projector”
(pages 21-22), enter “http://192.168.150.2/”.
3A screen for controlling the pro-
jector appears, ready for per-
forming various status condi-
tions, control, and settings.
After connecting the projector to your network, enter the projector IP address in “Address”
on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup
screen that will enable control of the projector via the network. 
						

							24
Confirming the Projector
Status (Status)
On this screen, you can confirm the projector
status. You can confirm the following items :
• •• •
•MAC Address
• •• •
•Power
• •• •
•Condition
• •• •
•Lamp Timer  1
• •• •
•Lamp Timer  2
• •• •
•Lamp Life 1
• •• •
•Lamp Life 2
• •• •
•Input
• •• •
•Signal Info
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
•For details about each item, refer to the
owner’s manual of the projector.
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector con-
trol. You can control the following items :
• •• •
•Power
• •• •
•Input Select
• •• •
•Volume
• •• •
•Mute (Audio) [OFF] [ON]
• •• •
•Black Screen [OFF] [ON]
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
•You cannot operate this page while the pro-
jector is warming up.
•While the projector is in standby mode, you
can only control “Power ON”.
•For details about each item, refer to the
owner’s manual of the projector. 
						

							25
Controlling the Projector via LAN
Setting and Adjusting the
Projector (Settings & Adjustments)
Example: “Picture” screen display for INPUT 1
On these screens, you can make projector
settings or adjustments. You can set or adjust
the following items :
• •• •
•Picture Mode
• •• •
•CLR Temp
• •• •
•Bright Boost
• •• •
•Progressive
• •• •
•C.M.S. Adjustment
• •• •
•DNR
• •• •
•Signal Type
• •• •
•Auto Sync
• •• •
•Auto Sync Disp
• •• •
•Audio Out
• •• •
•Internal Speaker [OFF][ON]
• •• •
•Resize
• •• •
•OSD Display
• •• •
•Video System (INPUT 4/5)
• •• •
•Background
• •• •
•Startup Image
• •• •
•Eco Mode [OFF][ON]
• •• •
•Auto Search [OFF][ON]
• •• •
•Auto Power Off [OFF][ON]
• •• •
•Lamp Mode
• •• •
•Projection Mode
• •• •
•Keylock Level
• •• •
•Set Inputs
• •• •
•RS-232C Speed
• •• •
•Monitor Out (Standby)
• •• •
•OSD Language
• •• •
•Video Wall (See page 41.)
• •• •
•Stack Setting (See page 38.)
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
•You cannot operate this page while the pro-
jector is warming up.
•While the projector is in standby mode, you
can only control “Power ON”.
•For details about each item, refer to the
owner’s manual of the projector.
Setting the Security
(Network – Security)
On this screen, you can make settings relat-
ing to security.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” button.
Note
•After setting items, wait for 10 seconds and
then re-access.
•User Name and Password can be up to 8
characters.
•You can input the characters below :
a-z, A-Z, 0-9, -, _
•To cancel User Name and Password, enter
nothing and then press “Apply” button.
Description
Setting of user name for
security protection.
Setting of password for
security protection.
It is possible to set up to three
IP addresses allowing connec-
tion to the projector.
No limits are set to IP addresses
connecting to the projector.
For security improvement, only an
IP address set by “Address 1-3”
can be connected to the projector.
Items
User Name
Password
Accept IP
Address
All IP
Addresses
From only
specific IP
addresses 
						

							26
Controlling the Projector via LAN
Making General Settings
for the Network 
(Network –
General)
On this screen, you can make general settings
relating to the network.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” button.
Note
•After setting items, wait for 10 seconds and
then re-access.
•Projector Name can be up to 12 characters.
•You can input the characters below :
A-Z, 0-9, -, _, (, ), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
Description
Setting the projector name.
Setting the time interval in
which the projector will be
automatically disconnected
from the network in units of a
minute (from 1 to 65535
minutes). If the set value is
made 0, the Auto Logout
function is disabled.
Setting the TCP port number
used when exchanging a data
with the projector (from 1025 to
65535).
Setting the port number used
when searching for the
projector (from 1025 to 65535).
Items
Projector
Name
Auto
Logout
Time
Data Port
Search
Por t
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the projector
has generated an error.
Note
•SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
•
You can input the characters below:
SMTP Server and Originator E-mail Address :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,
|, }, ~
, _, ’, ., @, `
(You can input “@” only one time for “Origi-
nator E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (, ),
space
•
If the settings of “3. Setting up a Network
Connection for the Projector” on pages 21
and 22 are incorrectly set, e-mail will not be
send.
Setting example / Remarks
Setting an SMTP server
address for e-mail transmis-
sion.
e.g.1 : 192.168.150.253
e.g.2 : smtp123.eiki.co.jp
*When using a domain name,
make settings for the DNS
server.
Setting the projector’s e-mail
address. The e-mail address set
here becomes Originator E-mail
Address.
Setting the sender’s name.
The name set here appears in
the “Originator Name” column
of the body of the message.
Items
SMTP
Server
Originator
E-mail
Address
Originator
Name 
						

							27
Controlling the Projector via LAN
Setting Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail destina-
tions to which error notification (error items)
e-mails are sent.
Note
•E-mail Address can be up to 64 characters.
•You can input the characters below :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,
}, ~
, _, ’, ., @, `
(You can input “@” only one time.)
•For details about error items, refer to the
owner’s manual of the projector.
Description
Set addresses to which error
notification e-mail is sent. You
can set up to five addresses.
Error e-mail is sent on the error
items checked in their check
boxes.
Send test e-mail. This allows
you to confirm that the settings
for e-mail transmission are
properly set.
Items
E-mail
Address
Error Mail
(Lamp, Temp,
Fan, Cover)
Test 
						

							28
Setting the Projector Using RS-232C or Telnet
When Connecting Using
RS-232C
1Launch general purpose terminal
emulator.
2Input settings for the RS-232C port
of the terminal emulator as follows.
Baud Rate : 9600 bps*
Data Length : 8 bit
Parity Bit : None
Stop Bit : 1 bit
Flow Control : None
*This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3Input “PJS11234” and press the
“Enter” key.
4“OK” is displayed. Input “PJS25678”
and press the “Enter” key within 10
seconds.
5“OK” is displayed. Press the “En-
ter” key.
6“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on
the computer to carry out various settings for the projector.
7“Password:” is displayed. Input the
password and press the “Enter” key.
•If a password has not yet been set, just press
the “Enter” key.
8Input “setup” and press the “Enter”
key.
•SETUP MENU will be displayed.
Note
•User name and password are not set in the fac-
tory default settings.
•If the user name or password is entered incor-
rectly three times, SETUP MENU will be quit. ▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup> 
						

							29
Setting the Projector Using RS-232C or Telnet
When Connecting Using
Telnet
1Click “start” from the Windows® desk-
top and select “Run”.
2Enter “telnet 192.168.150.2” in the text
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
3Click the “OK” button.
4“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
5“Password:” is displayed. Input the
password and press the “Enter” key.
•If a password has not yet been set, just press
the “Enter” key.
6Input “setup” and press the “Enter”
key.
•SETUP MENU will be displayed.
Note
•If the IP address has been changed, ensure to
enter the new IP address in step 2.
•User name and password are not set in the fac-
tory default settings.
•If the user name or password is entered incor-
rectly three times in steps 4 or 5, SETUP MENU
will be quit.
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
▼SETUP MENU 
						

							30
Setting the Projector Using RS-232C or Telnet
SETUP MENU (Main Menu)
[1]IP Address (Factory default setting : 192.168.150.2)
IP address settings. (Page 33)
[2]Subnet Mask (Factory default setting :
255.255.255.0)
Subnet mask settings. (Page 33)
[3] Default Gateway (Factory default setting : Not
Used)
Default gateway settings. (Page 33)
[4]User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page 34)
[5]Password (Factory default setting : Not Required)
Setting of password for security protection. (Page 34)
[6]RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud rate settings for the RS-232C terminals. (Page
34)
[7] Projector Name (Factory default setting : EIP-
4500)
It is possible to assign a projector name. (Page 34)
[A] Advanced Setup
Enters ADVANCED SETUP MENU. (Page 35)
[D] Disconnect All
Disconnect all connections. (Page 35)
[V] View All Setting
Displays all setting values. (Page 31)
Can also be used with ADVANCED SETUP MENU.
[S] Save & Quit
Save set values and quit menu. (Page 32)
[Q]Quit Unchanged
Quit menu without saving setting values. (Page 32)
ADVANCED SETUP MENU
[1]Auto Logout Time (Factory default setting : 5 min-
utes)
Setting of time until automatic disconnection of net-
work connection. (Page 35)
[2] Data Port (Factory default setting : 10002)
Setting the TCP port number used when exchang-
ing data. (Page 35)
[5] Network Ping Test
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally. (Page 36)
[6] Accept IP Addr(1)
[7] Accept IP Addr(2)
[8] Accept IP Addr(3)
[9] Accept All IP Addr (Factory default setting : Ac-
cept All)
For improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page 36)
[0] Search Port (Factory default setting : 9300)
Setting the port number used when searching for
the projector. (Page 37)
[!] Restore Default Setting
Restores all setting values that can be set using the
menu to the default state. (Page 37)
[Q]Return to Main Menu
Return to the main SETUP MENU. (Page 37)
▼SETUP MENU▼ADVANCED SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>