Eiki Eip-3000na Dlp Projector Owners Manual

27
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
Power cordSupplied
accessory
When connecting to the LAN terminal using a LAN cable
TX/RX LED (yellow)
Illuminates when transmit-
ting/receiving data.
LINK LED (green)
Illuminates when linked.
Hub
or
Computer
LAN cable (Category 5 type,
commercially available)To LAN terminal* To ensure safety, do not
connect the LAN terminal
with any cables that may
cause excessive...

28
Turning the Projector On/Off
Remove the lens cap and press
oSTANDBY-ON on the projector or
fON on the remote control.
• When System Lock is set, the keycode input box
appears. To cancel the keycode setting, input the
keycode that you have already set. See page 47
for details.
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green:The lamp is warming up
or shutting down.
Red:The lamp is shut down abnormally
or the lamp...

29
On-screen Display (confirmation message)
Turning the Power off (Put-
ting the Projector into
Standby Mode)
• Do not unplug the power cord during projec-tion or cooling fan operation. This can cause
damage due to rise in internal temperature,
as the cooling fan also stops.
Info
R
STANDBY
button
Power indicator
STANDBY-ON button
1
2Press  oSTANDBY-ON on the pro-
jector or  eSTANDBY on the re-
mote control, then press that but-
ton again while the confirmation
message is displayed, to put the
projector...

30
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Press pENTER to exit the Setup Guide
screen.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
STANDBY-ON
button
ENTER button
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Image Projection
Rotate the focus ring to adjust the fo-
cus while watching the projected image.
Setup Guide screen
• The Setup Guide screen automatically high-
lights the items...

31
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly...

32
Image Projection (Continued)
Displaying the Black Screen
and Turning off the Sound
Temporarily
Adjusting the Volume
Switching the Input Mode
PressCINPUT 1, CINPUT 2,
DINPUT 3 or EINPUT 4 on the remote
control to select the input mode.
• When pressing INPUT (P/R) on the projector,
input mode switches in the following order:
INPUT1 INPUT2 INPUT3 INPUT4.
• When “Auto Search” is set to “On”, INPUT (P/
R) on the projector functions as the Auto Search
buttons. (See page 46.)
Select the appropriate input...

33
0 KeystoneADJ. END
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
• The Keystone Correction can be adjusted up
to an angle of approximately ±13 degrees and
the screen can also be set up to an angle of
approximately ±13 degrees (when the resize
mode is set to “NORMAL” (see page 34)).
Note
1
2
3...

34
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
Press HRESIZE.• See page 44 for setting on menu screen.
Computer
Input Signal
NORMALOutput screen image
Computer Image type BORDER STRETCH
SXGA
(1280K1024)
1280K720
4:3 aspect ratio
5:4 aspect ratio
16:9 aspect
ratio
* Mode for projecting an image with the original
aspect ratio without...

35
VIDEO
•“STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
: Cutout area on which images cannot be projected.
: Area on which the image is not included in the original signals.Input Signal
DVD / Video Image typeOutput screen image
NORMAL
BORDERSTRETCH
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
540P, 720P, 1080I
4:3 aspect ratio
Letter box
Squeezed 16:9 image
Squeezed 4:3 image
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in
16:9 screen)
* Mode for projecting an image with the...

36
Auto Sync
(Auto Sync Adjustment)
Operating with the Remote Control
Freezing a Moving Image
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 51.)
Auto Sync function works when detect-
ing input signal after the projector turns
on.
Press FAUTO SYNC to manually ad-
just with Auto Sync function.
Press NFREEZE.
• The projected image is frozen.
Press NFREEZE again to return
to the moving image from the cur-
rently connected device.
1...